Search NASA⌕ Search

Engineering topics

Carpenter, Daniel L.

Publications and source records attributed to Carpenter, Daniel L..

Predicting Catalytic Pyrolysis Aromatic Selectivity from Pyrolysis Vapor Composition Using Mass Spectra Coupled with Statistical Analysis

The behavior of fast pyrolysis (FP) and catalytic FP (CFP) of 20 renewable feedstocks was studied in a microscale reactor with molecular beam mass spectral analysis of products generated. A partial least-squares (PLS) model was constructed based on the FP vapor spectra that predicts the aromatic selectivity when upgrading over a ZSM-5 catalyst. Additionally, principal component analysis of both FP and CFP spectra was performed for comprehensive spectral analysis. This work highlighted the value of vapor-phase mass spectral screening to predict the subsequent feedstock performance and demonstrated that the quantity of coke deposited on the catalyst is not a reliable measure of catalyst deactivation when the feedstock type is varied.

09 BIOMASS FUELS↗

Pilot plant reliability metrics for grinding and fast pyrolysis of woody residues

Here we report on the effects of loblolly pine residue variability on material throughput, pilot plant uptime, operator intervention, product yield, and product quality for grinding, fast pyrolysis, and hydrotreating operations. Preprocessing throughput using a hammer mill varied between 31-48% of nameplate capacity (5 tons/hr). Grinder overloads in the size reduction step were more prevalent for lower ash and higher moisture materials. Fast pyrolysis throughput varied between 57-72% of nameplate capacity (20 kg/hr) and bio-oil yields varied between 46-53% (feedstock carbon to oil, dry basis). During fast pyrolysis operations, downtime was caused by bridging in the feed and char removal systems and plugging in the condensation system. Cohesion of feedstock and char leading to system plugging was less frequent for higher ash feedstocks, and differences in condenser plugging behavior between high and low ash feedstocks were observed. The catalyst stability of the bio-oil stabilization step was strongly dependent on the sulfur content in the bio-oil, which was higher for the high-ash residue oils. Lower moisture content in the starting biomass was consistent with lower sulfur content in bio-oil. Yields and properties of hydrotreated fuel products showed minimal deference among the bio-oils.

Klinger, Jordan↗

Steam-air blown bubbling fluidized bed biomass gasification (BFBBG): Multi-scale models and experimental validation

During fluidized bed biomass gasification, complex gas-solid mixing patterns and numerous chemical and physical phenomena make identification of optimal operating conditions challenging. In this work, a parametric experimental campaign was carried out alongside the development of a coupled reactor network model which successfully integrates the individually validated sub-models to predict steady-state reactor performance metrics and outputs. The experiments utilized an integrated gasification system consisting of an externally-heated, bench-scale, 4-in., 5 kWth, fluidized bed steam/air blown gasifier fed with woody biomass equipped with a molecular beam mass spectrometer to directly measure tar species. The operating temperature (750-850°C) and air/fuel equivalence ratio (ER = 0-0.157) were independently varied to isolate their effects. Elevating temperature is shown to improve the char gasification rate and reduce tar concentrations. In conclusion, air strongly impacts the composition of tar, accelerating the conversion of lighter polycyclic-aromatic hydrocarbons into soot precursors, while also improving the overall carbon conversion.

09 BIOMASS FUELS↗

Effects of thermal pretreatment and catalyst on biomass gasification efficiency and syngas composition

This work explores the combined effects of thermal pretreatment and using a catalyst in situ on gasification carbon conversion efficiency, as well as product gas and tar content and compositions. To compare the effects of thermal pretreatment, pelletized and ground oak with three different levels of thermal pretreatment were gasified in a fluidized bed reactor. The pretreatments applied to the oak were (1) pelletization, (2) drying at 180 °C in air, and (3) torrefaction at 270 °C in nitrogen. The oak dried at 180 °C produced syngas of similar quality and approximately the same amount of char as untreated oak. Torrefaction at 270 °C resulted in syngas with a higher hydrogen to CO ratio, lower methane, and less than half of the total tar -- all of which are desirable properties in terms of product gas quality. However, the oak torrefied at 270 °C also produced more than two times the amount of char as the untreated, pelletized oak. To determine the effect of catalyst, a series of experiments were conducted using olivine impregnated with nickel and cerium as the fluidized bed material in the gasifier. These tests showed that modified olivine can improve hydrogen production and reduce methane and tar levels in the syngas. The result was observed for both treated and untreated oak; although the effect was more substantial for untreated oak, for which the use of modified olivine reduced tar concentrations in the product gas by 60%, with a larger reduction in heavier tars than lighter tars. Furthermore, this result is important because reduction in heavier tar plays a more important role in benefitting downstream operations.

09 BIOMASS FUELS↗

Effects of Torrefaction Temperature on Pyrolysis Vapor Products of Woody and Herbaceous Feedstocks

A variety of hardwood, softwood, and herbaceous feedstocks (oak, southern yellow pine mix, loblolly pine, pinyon-juniper mix, and switchgrass) were each torrefied at 200, 250, and 300 °C. Each of the feedstocks was pyrolyzed and the resulting vapors were analyzed with a molecular beam mass spectrometer (py-MBMS). Compositional analysis was used to measure the total lignin content of three of the feedstocks (southern yellow pine, softwood; oak, hardwood; and switchgrass, herbaceous) before and after torrefaction at 300 °C, and large differences in the fraction of lignin lost during torrefaction were found between feedstocks, with oak having the largest decrease in lignin during torrefaction and switchgrass having the least. Finally, it is hypothesized that these differences in the thermal degradation are due to, in part, the different ratios of S, G, and H lignins in the feedstocks. Additionally, the torrefaction of kraft lignin was studied using thermogravimetric analysis coupled with Fourier transform infrared spectroscopy (TGA-FTIR) and attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR).

09 BIOMASS FUELS↗