Search NASA⌕ Search

Engineering topics

Carraway, Debra L.

Publications and source records attributed to Carraway, Debra L..

17 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Active thermal isolation for temperature responsive sensors

A temperature responsive sensor is located in the airflow over the specified surface of a body and is maintained at a constant temperature. An active thermal isolator is located between this temperature responsive sensor and the specified surface of the body. The temperature of this isolator is controlled to reduce conductive heat flow from the temperature responsive sensor to the body. This temperature control includes: (1) operating the isolator at the same temperature as the constant temperature of the sensor and (2) establishing a fixed boundary temperature which is either less than or equal to or slightly greater than the sensor constant temperature.

Martinson, Scott D.↗
NASA NTRS1994

Active thermal isolation for temperature responsive sensors

The detection of flow transition between laminar and turbulent flow and of shear stress or skin friction of airfoils is important in basic research for validation of airfoil theory and design. These values are conventionally measured using hot film nickel sensors deposited on a polyimide substrate. The substrate electrically insulates the sensor and underlying airfoil but is prevented from thermally isolating the sensor by thickness constraints necessary to avoid flow contamination. Proposed heating of the model surface is difficult to control, requires significant energy expenditures, and may alter the basic flow state of the airfoil. A temperature responsive sensor is located in the airflow over the specified surface of a body and is maintained at a constant temperature. An active thermal isolator is located between this temperature responsive sensor and the specific surface of the body. The total thickness of the isolator and sensor avoid any contamination of the flow. The temperature of this isolator is controlled to reduce conductive heat flow from the temperature responsive sensor to the body. This temperature control includes (1) operating the isolator at the same temperature as the constant temperature of the sensor; and (2) establishing a fixed boundary temperature which is either less than or equal to, or slightly greater than the sensor constant temperature. The present invention accordingly thermally isolates a temperature responsive sensor in an energy efficient, controllable manner while avoiding any contamination of the flow.

Martinson, Scott D.↗
NASA NTRS1993

Active Thermal Isolation For Hot-Film Anemometers

Local heating compensates for conduction of heat from sensors into modules. Two hot-film sensors stacked on wind-tunnel model. Outer sensor detects changes in boundary-layer flow. Inner sensor provides active thermal isolation between outer sensor and model. Thermal boundary condition controlled at response time of detection hot-film sensor, significantly less than response time of internally heated model. Requires less power to maintain outer hot-film sensor at given temperature, enabling system to respond over greater dynamic range before power limits of instrument reached. Stacked sensors bonded to surface of most wind-tunnel models, even to curved surfaces, and removed after completion of experiments.

Martinson, Scott D.↗
NASA NTRS1991

Convective response of a wall-mounted hot-film sensor in a shock tube

Shock tube experiments were performed in order to determine the response of a single hot-film element of a sensor array to transiently induced flow behind weak normal shock waves. The experiments attempt to isolate the response due only to the change in convective heat transfer at the hot-film surface mounted on the wall of the shock tube. The experiments are described, the results being correlated with transient boundary layer theory and compared with an independent set of experimental results. One of the findings indicates that the change in the air properties (temperature and pressure) precedes the air mass transport, causing an ambiguity in the sensor response to the development of the velocity boundary layer. Also, a transient, local heat transfer coefficient is formulated to be used as a forcing function in an hot-film instrument model and simulation which remains under investigation.

Roberts, A. Sidney, Jr.↗
NASA NTRS1991

The use of silicon microsensors in smart skins for aerodynamic research

A futuristic look at what should be pursued in terms of measurement instrumentation for aerodynamic research is presented. A cursory method is given for incorporating silicon microsensors, signal conditioning, and signal processing into a thin skin which will ultimately become the surface of an airfoil. Polyimide is the candidate material suggested for use as the skin because of its flexibility and IC processing compatibility. Specifications are given for the detection of boundary layer phenomena of current interest.

Carraway, Debra L.↗
NASA NTRS1990

Transition detection studies in the cryogenic environment

Boundary-layer transition detection studies were carried out in the 0.3 Meter Transonic Cryogenic Tunnel on a supercritical airfoil, using an infrared imaging system. The purpose of the experiments was to determine the extent of the temperature range in which commercially available IR systems can detect transition in cryogenic environment. The experiment was designed to take advantage of a combination of factors including the wind tunnel operation mode, the model construction materials and the IR system image processing options. During the initial phases of the study, the IR based findings were confirmed by measurements done with a micro-thin hot-film system. Ultimately, free and forced transition could be detected down to 170 K.

Gartenberg, Ehud↗
NASA NTRS1989

A transition detection study at Mach 1.5, 2.0, and 2.5 using a micro-thin hot-film system

A boundary-layer transition detection study was conducted in the NASA Langley unitary plan wind tunnel with an array of microthin hot films on a flat plate at Mach numbers 1.5, 2.0, and 2.5 and Reynolds numbers (1.0-4.5) x 10 to the 6th/ft. Transition locations were obtained online from the variation of normalized rms voltages from an array of hot-film sensors for both natural transition and a grit-induced wedge of turbulence. The effects of Mach number and Reynolds number on the location and length of the transition region for the two types of transition are presented from the online data. Also shown are the unit Reynolds number effects on transition Reynolds number, voltage-versus-time traces, spectra, and the data-acquisition system.

Johnson, Charles B.↗
NASA NTRS1989

Use of piezoelectric foil for flow diagnostics

A laboratory investigation was conducted to characterize two piezoelectric-film sensor configurations, a rigidly mounted sensor and a sensor mounted over an air cavity. The sensors are evaluated for sensitivity and frequency response, and methods to optimize data are presented. The cavity-mounted sensor exhibited a superior frequency response and was more sensitive to normal pressure fluctuations and less sensitive to vibrations through the structure. Both configurations were sensitive to large-scale structural vibrations. Flight-test data are shown for cavity-mounted sensors, illustrating practical aspects to consider when designing sensors for application in such harsh environments. The relation of the data to skin friction and maximum shear stress, transition detection, and turbulent viscous layers is derived through analysis of the flight data.

Carraway, Debra L.↗
NASA NTRS1988

Laminar-Separation Sensor

Sensor detects flow reversal in boundary layer. Laminar-separation sensor provides means for detecting laminar-separation bubble by use of very thin, surface-mounted sensor. Consists of flush array of three proximate thin films. Middle film electronically heated by means of constant-temperature anemometer (CTA). Outer films, one upstream and one downstream of middle film, incorporated into bridge circuit to respond as resistance thermometers. This sensor provides only known surface-mounted means for positively identifying pressure of laminar separation as cause of boundary-layer transition.

Holmes, Bruce J.↗
NASA NTRS1988

Crossflow vorticity sensor

A crossflow vorticity sensor for the detection of crossflow vorticity characteristics is described. The sensor is comprised of crossflow sensors which are noninvasively adhered to a swept wing laminar surface either singularly, in multi-element strips, in polar patterns, or in orthogonal patterns. These crossflow sensors are comprised of hot-film sensor elements which operate as a constant temperature anemometer circuit to detect heat transfer rate changes. Accordingly, crossflow vorticity characteristics are determined via cross-correlation. In addition, the crossflow sensors have a thickness which does not exceed a maximum value h in order to avoid contamination of downstream crossflow sensors.

Holmes, Bruce J.↗
NASA NTRS1988

Laminar-Boundary-Layer Crossflow Sensor

Crossflow vorticity detected with nonintrusive electronic sensor elements. Individual crossflow sensor elements respond to variation in heat transfer caused by laminar-crossflow vortexes. Installed in variety of patterns, including staggered or combined into continuous longitudinal strip.

Holmes, Bruce J.↗
NASA NTRS1987

Advanced measurement techniques, part 1

In modern laminar flow flight and wind tunnel research, it is important to understand the specific cause(s) of laminar to turbulent boundary layer transition. Such information is crucial to the exploration of the limits of practical application of laminar flow for drag reduction on aircraft. The process of transition involves both the possible modes of disturbance growth, and the environmental conditioning of the instabilities by freestream or surface conditions. The possible modes of disturbance growth include viscous, inviscid, and modes which may bypass these natural ones. Theory provides information on the possible modes of disturbance amplification, but experimentation must be relied upon to determine which of those modes actually dominates the transition process in a given environment. The results to date of research on advanced devices and methods used for the study of transition phenomena in the subsonic and transonic flight and wind tunnel environments are presented.

Holmes, Bruce J.↗
NASA NTRS1987

Hot-film system for transition detection in cryogenic wind tunnels

It is well known that the determination of the location of boundary-layer transition is necessary for the correct interpretation of aerodynamic data in transonic wind tunnels. In the late 1970s the Douglas Aircraft Company developed a vapor deposition hot-film system for transition detection in cryogenic wind tunnels. Tests of the hot-films in a low-speed tunnel demonstrated the ability to obtain on-line transition data with an enhanced simultaneous hot-film data acquisition system. The equipment design and specifications are described.

Johnson, Charles B.↗
NASA NTRS1987

Remote noncontacting measurements of heat transfer coefficients for detection of boundary layer transition in wind tunnel tests

An infrared measurement system is used that consists of a laser heating source, an infrared camera for data acquisition, and a video recorder for data storage. A laser beam is scanned over an airfoil, heating its surface to a few degrees above ambient. An infrared camera then measures the temperature of the airfoil over a two-dimensional field, and these temperatures are stored as a function of time on a video recorder. The resulting temperature pictures are digitized and an iterative approximation algorithm is used to extract the heat transfer coefficient. The resulting values are normalized to the natural convection condition. The technique has been applied in low-speed wind tunnel tests and compared to well-established hot-film measurements which were made simultaneously to confirm the flow conditions. Heat transfer coefficients were determined using a linear scanning pattern, to indicate the position of natural and of artificially induced transition on an airfoil, at various wind speeds. The technique is shown to be sensitive to transition at low Mach numbers. The advantages of the technique are discussed.

Heath, D. Michele↗
NASA NTRS1987

Status of a specialized boundary layer transition detection system for use in the U.S. National Transonic Facility

An improved deposition technique for cryogenic hot films used for transition detection in cryogenic tunnels is reported. Tests of the hot films in a low-speed tunnel demonstrated the ability to obtain online transition data. The capability of an enhanced hot film data acquisition system was also demonstrated. A comparison of data from the new system with stability theory shows the detection of Tollmein-Schlicting waves at transition onset.

Johnson, Charles B.↗
NASA NTRS1986

Boundary layer measurements using hot-film sensors

Measurements in the aerodynamic boundary layer using heat transfer, hot-film sensors are receiving a significant amount of effort at the Langley Research Center. A description of the basic sensor, the signal conditioning employed, and several manifestations of the sensor are given. Results of a flow reversal sensor development are presented, and future work areas are outlined.

Holmes, Harlan K.↗