Engineering topics

Carter, A. L.

Publications and source records attributed to Carter, A. L..

10 records

DOE OSTI2022

Development of the MCNP-ORIGEN activation automation tool

This paper introduces the MCNP-ORIGEN activation automation tool for streamlining the calculation of experiment source terms. This tool couples the Monte-Carlo radiation-transport solver, MCNP to the depletion tool, ORIGEN-S. To showcase its current capabilities, this paper presents an activation analysis exercise, which is conducted with Serpent, and the results are com- pared. The experiment consists in a 90%-enriched uranium sphere surrounded by light water. A non-fissile cylinder is placed in the water, representing an irradiation experiment. We conducted simulations for 2 different cylinder materials: iron and cobalt at two different temperatures: 300 K and 900 K. The exercise consists of an irradiation of 50 days at a constant power of 5 MW, followed by a decay of 50 days. These studies highlight the discrepancies between how the different tools handle nuclear data. Finally, the results underscore multiple areas of possible improvement.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1989

Application of fracture mechanics and half-cycle method to the prediction of fatigue life of B-52 aircraft pylon components

Stress intensity levels at various parts of the NASA B-52 carrier aircraft pylon were examined for the case when the pylon store was the space shuttle solid rocket booster drop test vehicle. Eight critical stress points were selected for the pylon fatigue analysis. Using fracture mechanics and the half-cycle theory (directly or indirectly) for the calculations of fatigue-crack growth ,the remaining fatigue life (number of flights left) was estimated for each critical part. It was found that the two rear hooks had relatively short fatigue life and that the front hook had the shortest fatigue life of all the parts analyzed. The rest of the pylon parts were found to be noncritical because of their extremely long fatigue life associated with the low operational stress levels.

Ko, W. L.↗

NASA NTRS1982

Strain gage load measurement on the shuttle orbiter

This paper describes the application of the calibrated strain gage load measurement method to the shuttle orbiter. Descriptions of instrumentation and calibration are included, along with comparisons of measured results with wind tunnel and FLEXSTAB analytical predictions.

Carter, A. L.↗

NASA NTRS1981

Comparison of wind tunnel and theoretical aeroelastic predictions with flight measured airloads for the B-1 aircraft

An aeroelastic analysis of the B-1 aircraft was generated using the FLEXSTAB computer program. Relatively simple aerodynamic and structural models were employed. Theoretical wing and horizontal stabilizer airloads were compared to wind tunnel predictions and flight data measured during quasi-steady pitch maneuvers at Mach numbers of 0.85 and 1.2 with the wing in the 67.5 degree full aft sweep position. The basic objective was to evaluate the usefulness of the FLEXSTAB program for pre-flight airloads analysis of large flexible aircraft. Significant aeroelastic increments were noted between rigid and flexible vehicle results. FLEXSTAB predicted airloads for the outer wing panel were in good agreement with measured data for both rigid airloads and elastic increments. FLEXSTAB results for the horizontal stabilizer were useful for defining general aeroelastic trends, but absolute load levels were not well predicted due to theoretical limitations and difficulties encountered in modelling the complex B-1 configuration. Overall, the FLEXSTAB program is viewed as a useful integrated tool for static aeroelastic analysis in support of flight programs.

Sims, R. L.↗

NASA NTRS1981

Comparison of theoretical predictions of orbiter airloads with wind tunnel and flight test results for a Mach number of 0.52

The measurement and prediction of wing airloads for space shuttle orbiter 101 during approach and landing tests is discussed. Strain gage instrumentation, calibration, and flight data processing are covered along with wind tunnel and simulator results. The generation of theoretical predictions using the FLEXSTAB computer program is described, and the results are compared to experimental measurements.

Carter, A. L.↗

NASA NTRS1978

Correlation of predicted and measured thermal stresses on a truss-type aircraft structure

A test structure representing a portion of a hypersonic vehicle was instrumented with strain gages and thermocouples. This test structure was then subjected to laboratory heating representative of supersonic and hypersonic flight conditions. A finite element computer model of this structure was developed using several types of elements with the NASA structural analysis (NASTRAN) computer program. Temperature inputs from the test were used to generate predicted model thermal stresses and these were correlated with the test measurements.

Jenkins, J. M.↗

NASA NTRS1977

Strain gage calibration of a complex wing

Modern complex structural arrangements have complicated the task of measuring flight loads with calibrated strain gages. This paper examines the use of a relatively simple structural model to characterize the load responses of strain gages located on various spars of a delta wing. Strains measured during a laboratory load calibration of a wing structure are compared with calculations obtained from a simplified NASA structural analysis (NASTRAN) model. Calculated and measured influence coefficient plots that show the shear, bending, and torsion characteristics of typical strain-gage bridges are presented. Typical influence coefficient plots are given for several load equations to illustrate the derivation of the equations from the component strain-gage bridges. A relatively simple structural model was found to be effective in predicting the general nature of strain distributions and influence coefficient plots. The analytical processes are shown to be useful in obtaining a good load calibration. The analytical processes cannot, however, be used in lieu of an actual load calibration of an aircraft wing.

Jenkins, J. M.↗

NASA NTRS1977

The use of a simplified structural model as an aid in the strain gage calibration of a complex wing

The use of a relatively simple structural model to characterize the load responses of strain gages located on various spars of a delta wing is examined. Strains measured during a laboratory load calibration of a wing structure are compared with calculations obtained from a simplified structural analysis model. Calculated and measured influence coefficient plots that show the shear, bending, and torsion characteristics of typical strain gage bridges are presented. Typical influence coefficient plots are shown for several load equations to illustrate the derivation of the equations from the component strain gage bridges. A relatively simple structural model was found to be effective in predicting the general nature of strain distributions and influence coefficient plots. The analytical processes are shown to be an aid in obtaining a good load calibration. The analytical processes cannot, however, be used in lieu of an actual load calibration of an aircraft wing.

Jenkins, J. M.↗

NASA NTRS1976

Fabrication and evaluation of advanced titanium and composite structural panels

Advanced manufacturing methods for titanium and composite material structures are being developed and evaluated. The focus for the manufacturing effort is the fabrication of full-scale structural panels which replace an existing shear panel on the upper wing surface of the NASA YF-12 aircraft. The program involves design, fabrication, ground testing, and Mach 3 flight service of full-scale structural panels and laboratory testing of representative structural element specimens.

Bales, T. T.↗

NASA NTRS1975

Fabrication methods for YF-12 wing panels for the Supersonic Cruise Aircraft Research Program

Advanced fabrication and joining processes for titanium and composite materials are being investigated by NASA to develop technology for the Supersonic Cruise Aircraft Research (SCAR) Program. With Lockheed-ADP as the prime contractor, full-scale structural panels are being designed and fabricated to replace an existing integrally stiffened shear panel on the upper wing surface of the NASA YF-12 aircraft. The program involves ground testing and Mach 3 flight testing of full-scale structural panels and laboratory testing of representative structural element specimens. Fabrication methods and test results for weldbrazed and Rohrbond titanium panels are discussed. The fabrication methods being developed for boron/aluminum, Borsic/aluminum, and graphite/polyimide panels are also presented.

Hoffman, E. L.↗