Search NASA⌕ Search

Engineering topics

Cary, A. M., Jr.

Publications and source records attributed to Cary, A. M., Jr..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Drag reduction characteristics of small amplitude rigid surface waves

The possibility of reducing drag by using rigid, wavy surfaces is investigated both analytically and experimentally. Although pressure drag for rigid sine-wave surfaces can be predicted empirically, viscous drag for even shallow waves was poorly predicted by state-of-the-art turbulent boundary layer calculation procedures. Calculations for the effects of geometric and fluid variables on total wave drag are presented under the philosophy that trends will be nearly correct even though levels are probably incorrect. Experiments by the present authors indicate that a total drag reduction with wavy walls is possible.

Cary, A. M., Jr.↗
NASA NTRS1977

Calculation of turbulent boundary layers with tangential slot injection

Paper describes a numerical calculation scheme for tangential slot injection (wall-wake) flows; application of the scheme over a wide range of flow conditions indicates increased accuracy compared to previous work. Predictions from the numerical code were in good agreement with experiment (velocity profile, skin-friction, and effectiveness data) for low- and high-speed flows. To achieve improved accuracy, modifications in the turbulence modeling, compared to previous research, were necessary for the imbedded shear layer region in the near field and for the wall region near shear layer impingement. Anomalous behavior was noted for far field experimental velocity profiles in low-speed flow when the slot-to-free stream velocity ratio was near one

Cary, A. M., Jr.↗
NASA NTRS1977

Influence of transverse surface waves on turbulent boundary layers

Wavy wall experiments using solid waves and progressive waves have been reported. For this paper, the major effects of waviness of the wall on the flow are identified as due to oscillatory curvature (convex-concavity) and oscillatory acceleration/deceleration of the flow, which imposes a highly nonequilibrium influence upon the turbulence structure. The theoretical analysis in this presentation takes into account proper turbulence modeling (including the nonequilibrium effects) for the wavy wall problem. The analysis proceeds in three stages: (1) inviscid solution for induced pressure due to the physical wall, (2) solution of a turbulent boundary layer with pressure gradients and curvature effects in the modeling from which the profile correction is computed, and (3) induced pressure computations for the corrected profile. The phase shift of pressure perturbations with respect to the physical wall can be predicted, and pressure drag and skin friction drag can be estimated, with nonlinear viscous effects included. Comparison of the theoretical estimates with experimental data are also presented.

Balasubramanian, R.↗
NASA NTRS1977

Downstream influence of swept slot injection in hypersonic turbulent flow

Results of an experimental and numerical investigation of tangential swept slot injection into a thick turbulent boundary layer at Mach 6 are presented. Film cooling effectiveness, skin friction, and flow structure downstream of the swept slot injection were investigated. The data were compared with that for unswept slots, and it was found that cooling effectiveness and skin friction reductions are not significantly affected by sweeping the slot.

Hefner, J. N.↗
NASA NTRS1977

Calculation methods for compressible turbulent boundary layers, 1976

Equations and closure methods for compressible turbulent boundary layers are discussed. Flow phenomena peculiar to calculation of these boundary layers were considered, along with calculations of three dimensional compressible turbulent boundary layers. Procedures for ascertaining nonsimilar two and three dimensional compressible turbulent boundary layers were appended, including finite difference, finite element, and mass-weighted residual methods.

Bushnell, D. M.↗
NASA NTRS1976

Calculation methods for compressible turbulent boundary layers

Calculation procedures for non-reacting compressible two- and three-dimensional turbulent boundary layers were reviewed. Integral, transformation and correlation methods, as well as finite difference solutions of the complete boundary layer equations summarized. Alternative numerical solution procedures were examined, and both mean field and mean turbulence field closure models were considered. Physics and related calculation problems peculiar to compressible turbulent boundary layers are described. A catalog of available solution procedures of the finite difference, finite element, and method of weighted residuals genre is included. Influence of compressibility, low Reynolds number, wall blowing, and pressure gradient upon mean field closure constants are reported.

Bushnell, D. M.↗
NASA NTRS1975

Mixing length in low Reynolds number compressible turbulent boundary layers

The paper studies the effect of low Reynolds number in high-speed turbulent boundary layers on variations of mixing length. Boundary layers downstream of natural transition on plates, cones and cylinders, and boundary layers on nozzle walls without laminarization-retransition are considered. The problem of whether low Reynolds number amplification of shear stress is a result of transitional flow structure is considered. It is concluded that a knowledge of low Reynolds number boundary layer transition may be relevant to the design of high-speed vehicles.

Bushnell, D. M.↗
NASA NTRS1974

Engineering prediction of turbulent skin friction and heat transfer in high-speed flow

A large collection of experimental turbulent-skin-friction and heat-transfer data for flat plates and cones was used to determine the most accurate of six of the most popular engineering-prediction methods; the data represent a Mach number range from 4 to 13 and ratio of wall to total temperature ranging from 0.1 to 0.7. The Spalding and Chi method incorporating virtual-origin concepts was found to be the best prediction method for Mach numbers less than 10; the limited experimental data for Mach numbers greater than 10 were not well predicted by any of the engineering methods except the Coles method.

Cary, A. M., Jr.↗
NASA NTRS1974

Investigation of the three-dimensional turbulent flow downstream of swept slot injection in hypersonic flow

Results of an experimental and numerical investigation of tangential swept slot injection (sweep angles of 22.5 and 45 deg) into a thick turbulent boundary layer at Mach 6 are presented. Film cooling effectiveness, skin friction, and flow structure downstream of the swept slot injection are investigated. The data are compared to that for unswept slots, and it is found that cooling effectiveness and skin-friction reductions are not significantly affected by sweeping the slot. Predictions of cooling effectiveness and skin friction obtained by a numerical finite-difference technique agree reasonably well with experimental surface variables. As in previous supersonic two-dimensional slot research, reduced mixing was found downstream of the slot lip in the present three-dimensional case.

Hefner, J. N.↗
NASA NTRS1974

Swept-slot film-cooling effectiveness in hypersonic turbulent flow

Measurement results are presented for the surface equilibrium temperature downstream of swept slots, with sonic tangential air injection into a thick hypersonic turbulent boundary layer. These results are compared with unswept slot results for cooling effectiveness.

Hefner, J. N.↗
NASA NTRS1972

Discrete sonic jets used as boundary-layer trips at Mach numbers of 6 and 8.5

The effect of discrete three-dimensional sonic jets used to promote transition on a sharp-leading-edge flat plate at Mach numbers of 6 and 8.5 and unit Reynolds numbers as high as 2.5 x 100,000 per cm in the Langley 20-inch hypersonic tunnels is discussed. An examination of the downstream flow-field distortions associated with the discrete jets for the Mach 8.5 flow was also conducted. Jet trips are found to produce lengths of turbulent flow comparable to those obtained for spherical-roughness-element trips while significantly reducing the downstream flow distortions. A Reynolds number based upon secondary jet penetration into a supersonic main flow is used to correlate jet-trip effectiveness just as a Reynolds number based upon roughness height is used to correlate spherical-trip effectiveness. Measured heat-transfer data are in agreement with the predictions.

Stone, D. R.↗