Engineering topics

Casey, D. T. (ORCID:000000032125677X)

Publications and source records attributed to Casey, D. T. (ORCID:000000032125677X).

6 records

DOE OSTI2025

High-compression implosions based on high density carbon ablator using modified drive and capsule dopant profiles

Laser-driven inertial fusion experiments have, for the first time, achieved a target gain greater than unity in a laboratory setting [Abu-Shawareb et al., Phys. Rev. Lett. 132, 065102 (2024)]. Despite this breakthrough, the burn-up fraction remains limited to about one-fourth of ideal estimates due to insufficient areal density, highlighting the potential for greater gains through enhanced compression. In our previous work, we demonstrated record-high compression of stagnated fuel in indirectly driven implosions using high-density carbon ablators. This was achieved by combining a continuous ramped pulse drive with a modified ablator dopant profile, which reduced mixing at the fuel–ablator interface and improved stability [Tommasini et al., Phys. Rev. Res. 5, L042034 (2023)]. Based on this foundation, the study presented here investigates the limits of compression achievable by combining the continuous ramped pulse drive with different dopant profiles to further minimize unstable interfaces and gradient discontinuities, thereby reducing fuel–ablator mixing. Our results demonstrate that the continuous ramped pulse consistently outperforms designs based on 3-shock drive pulses across all ablator profiles studied, with compression showing only a relatively modest dependence on dopant configurations that reduce the number of interfaces or eliminate discontinuities in the dopant gradient profile. Sub-scale experiments using the continuous ramped pulse achieved compression levels exceeding those of full-scale “HyE” implosions [Kritcher et al., Phys. Plasmas 28, 072706 (2021)] at similar adiabat, anticipating significant performance gains with increased scale, as supported by models and simulations. These findings underscore the critical role of the continuous ramped pulse in reducing mix and achieving improved compression. They also provide a foundation for future large-scale experiments to test the continuous ramped pulse design on deuterium–tritium fuel in the burn-wave propagation regime, leveraging the most effective combinations of continuous ramped pulse and dopant profiles identified in this study.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Constraining the 3He + 3He Gamow energy probed in high energy density plasmas at the National Ignition Facility

Polar-direct-drive implosions at the National Ignition Facility generated large plasma volumes to study the 3He + 3He fusion reaction. The ion temperature, which determines the Gamow peak energy, was constrained by isolating the thermal contribution to the D3He-proton spectral width in a 3He plasma doped with deuterium. X-ray penumbral imaging was used to measure electron temperature, density, and hotspot volume, which was subsequently used to model the spectral broadening from plasma stopping power. Results showed 30% of the D3He-proton spectral width was due to stopping power, with residual flows contributing ≈10%. The 3He temperature was determined as T3He = 12.4 ± 3.2 keV, corresponding to a Gamow energy of 95 ± 14 keV. These experiments achieved the lowest Gamow energy to date for studying 3He + 3He fusion in high energy density plasma, approaching conditions in the Sun.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Ultra-fast single-crystal CVD diamonds in the particle time-of-flight (PTOF) detector for low yield burn-history measurements on the NIF (invited)

The Particle Time of Flight (PTOF) diagnostic is a chemical vapor deposition diamond-based detector and is the only diagnostic for measuring nuclear bang times of low yield (<1013) shots on the National Ignition Facility. Recently, a comprehensive study of detector impulse responses revealed certain detectors with very fast and consistent impulse responses with a rise time of <50 ps, enabling low yield burn history measurements. At the current standoff of 50 cm, this measurement is possible with fast 14 MeV neutrons from deuterium–tritium (DT) fusion plasmas. PTOF-inferred DT burn width numbers compare well with widths inferred from the gamma reaction history diagnostic on mid-yield (1013–1015) shots, where both systems are capable of making this measurement. These new capabilities could be extended to 2.5 MeV deuterium–deuterium neutrons from D plasmas and to even lower yield by reducing the detector standoff distance to 10 cm; a design for this is also presented.

42 ENGINEERING↗

DOE OSTI2024

Thermonuclear performance variability near ignition at the National Ignition Facility

We describe our current understanding of the variability and degradation mechanisms observed through a series of five indirectly driven inertial fusion implosions fielded at the National Ignition Facility in the fall of 2021, four of which attempted to reproduce the first experiment to achieve Lawson's criterion for ignition with a thermonuclear yield of 1.35 MJ on August 8, 2021. A large number of absolutely calibrated (imaging, time-resolved, and spectrally resolved) x-ray and neutron diagnostics are fielded on the NIF along multiple lines of sight for each experiment. This allows for a reconstruction of the DT fuel and ablator mix injected into the hotspot around peak burn. We show that nuclear yield variations are well reproduced by numerical modeling when the measured low mode asymmetries and mix mass are included. Furthermore, these observed perturbations during burn are linked to small variations in laser delivery and capsule defects. Stringent specifications are then set to achieve robust ignition with the implosion design studied in this paper.

Divol, L. (ORCID:0000000269699898)↗

DOE OSTI2024

Design and analysis of dudded fuel experiments at the National Ignition Facility

Recent experiments conducted at the National Ignition Facility (NIF) within the past 2 years have achieved the burning plasma state and exceeded the Lawson criterion for the first time in the laboratory. Here, we report on a set of experiments where the deuterium and tritium (DT) ice layers were replaced with dudded tritium, hydrogen, and deuterium (THD) fuel mixtures to remove the influence of alpha-heating on hot spot dynamics. The hot spot compression and yield in the absence of alpha particle self-heating were measured to assess the proximity of NIF implosions toward the ignition cliff. We find that the “burn-off” Lawson parameters χnoα inferred from the THD experiments are in good agreement with the inferences from postshot simulations of the DT-layered implosions. The THD for burning plasma shot N210307 yielded χnoα≈0.88±0.03 while the THD for ignition shot N210808 yielded χnoα≈1.04±0.04. These results also provide important context for the observed variability in the repeat attempts of ignition shot N210808 since implosions on the ignition cliff are expected to exhibit very large variations in the fusion yield from small changes in the initial conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

What next: Further implosion space exploration on the path to NIF extended yield capability

We present quantitative motivations and assessments of various proposed and ongoing directions to further improving yields and target gain of igniting indirect-drive implosions at the National Ignition Facility (NIF). These include increasing compression and confinement time, improving hohlraum and ablator efficiency, and further increasing peak power and laser energy. 1D hydroscaled simulations, augmented by analytic 1D theory, have been used to project yield improvements for each of these implosion optimization tracks, normalized to the best current performing 4 MJ shot. At current NIF capabilities of 2.2 MJ, 450 TW, we project several paths could reach 15 MJ yield levels. We also expect several key implosion physics questions will be addressed in attempting to reach this yield level. These include demonstrating to what extent lower adiabat designs leading to higher compression will increase gain and efficiency, and whether we can reduce residual kinetic energy and ablator-fuel mix that is probably limiting the current burn-up fraction. For an envisaged NIF upgrade to EL = 3 MJ at fixed 450 TW peak power, scaling capsule size and fuel thicknesses faster than pure hydroscaling should allow for yields that could reach up to 60–80 MJ, depending on the efficiency gains realized in increasing deuterium-tritium fuel thickness, reducing hohlraum losses, and switching to lower Z ablators. The laser-plasma instability and beam transmission scaling in these larger hohlraums is shown to be favorable if the spot size is increased with hohlraum scale.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗