Search NASA⌕ Search

Engineering topics

Cassidy, J. F.

Publications and source records attributed to Cassidy, J. F..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Space power development impact on technology requirements

The paper is concerned with the selection of a specific spacecraft power technology and the identification of technology development to meet system requirements. Requirements which influence the selection of a given technology include the power level required, whether the load is constant or transient in nature, and in the case of transient loads, the time required to recover the power, and overall system safety. Various power technologies, such as solar voltaic power, solar dynamic power, nuclear power systems, and electrochemical energy storage, are briefly described.

Cassidy, J. F.↗
NASA NTRS1977

Emissions and Total Energy Consumption of a Multicylinder Piston Engine Running on Gasoline and a Hydrogen-gasoline Mixture

A multicylinder reciprocating engine was used to extend the efficient lean operating range of gasoline by adding hydrogen. Both bottled hydrogen and hydrogen produced by a research methanol steam reformer were used. These results were compared with results for all gasoline. A high-compression-ratio, displacement production engine was used. Apparent flame speed was used to describe the differences in emissions and performance. Therefore, engine emissions and performance, including apparent flame speed and energy lost to the cooling system and the exhaust gas, were measured over a range of equivalence ratios for each fuel. All emission levels decreased at the leaner conditions. Adding hydrogen significantly increased flame speed over all equivalence ratios.

Cassidy, J. F.↗
NASA NTRS1972

Space simulation experiments on reaction control system thruster plumes.

A space simulation procedure was developed for studying rocket plume contamination effects using a 5-lb bipropellant reaction control system thrustor. Vacuum chamber pressures of 0.00003 torr (70 miles altitude) were achieved with the thrustor firing in pulse trains consisting of eight pulses - 50 msec on, 100 msec off, and seven minutes between pulse trains. The final vacuum was achieved by cooling all vacuum chamber surfaces to liquid-helium temperature and by introducing a continuous argon leak of 48 std. cc/sec into the test chamber. Fast time response liquid flow rate measurements showed that large variations occurred in the ratio of oxidizer to fuel flow for pulse-on times up to 120 msec. These variations could lead to poor combustion efficiency and the production of contamination.

Cassidy, J. F.↗
NASA NTRS1972

Optical properties of thermal control coatings contaminated by MMH/N2O4 5-pound thruster in a vacuum environment with solar simulation.

Cat-a-lac Black and S13G thermal control coatings were exposed to the exhaust of a thrustor in a simulated space environment. Vacuum was maintained at less than 10 microtorr during thrustor firing in the liquid helium cooled facility. The thrustor was fired in a 50-millisecond pulse mode, and the accumulated firing time was 224 seconds. Solar absorptance and thermal emittance of the coatings were measured in-situ at intervals of 300 pulses, using a calorimetric technique. The Cat-a-lac Black coatings showed no change in solar absorptance or thermal emittance. The S13G showed up to 25% increase in solar absorptance but no change in thermal emittance.

Sommers, R. D.↗
NASA NTRS1972

Optical properties of thermal control coating contaminated by MMH/N2O4 5-pound thruster in a vacuum environment with solar simulation

Cat-a-lac Black, and S13G thermal control coatings were exposed to the exhaust of a thruster in a simulated space environment. Vacuum was maintained at less than 10 to the minus 5th power torr during thruster firing in the liquid helium cooled facility. The thruster was fired in a 50-millisecond pulse mode and the accumulated firing time was 224 seconds. Solar absorptance (alpha sub s) and thermal emittance (sigma) of the coatings were measured in-situ at intervals of 300 pulses. A calorimetric technique was used to measure alpha sub s and sigma. The tests, technique, and test results are presented. The Cat-a-lac Black coatings showed no change in alpha sub s or sigma. The S13G showed up to 25 percent increase in alpha sub s but no change in sigma.

Sommers, R. D.↗
NASA NTRS1972

The effect of rocket plume contamination on the optical properties of transmitting and reflecting materials.

The preliminary results of plume contamination from a 5-pound thrust single-doublet, bipropellant rocket engine on the transmittance of quartz and the reflectance of a silicon monoxide overcoated aluminum mirror have been presented. Changes in quartz transmittance were found to be significant and were due to both absorption and scattering effects. Contaminant absorption effects were predominant at the short wavelengths and scattering effects were greatest in the visible wavelengths. Measured changes in mirror reflectance were due primarily to contaminant absorption. Scattering effects were found to be as much as 9% of the total reflected energy from the mirror. There were no noticeable chemical or erosion effects on either the quartz or the front surface mirror.

Jack, J. R.↗
NASA NTRS1972

Space simulation experiments on reaction control system thruster plumes

A space simulation procedure was developed for studying rocket plume contamination effects using a 5-pound bipropellant reaction control system thruster. Vacuum chamber pressures of 3 x 10 to the minus 5 torr (70 miles altitude) were achieved with the thruster firing in pulse trains consisting of eight pulses (50 msec on, 100 msec off, and seven minutes between pulse trains). The final vacuum was achieved by cooling all vacuum chamber surfaces to liquid helium temperature and by introducing a continuous argon leak of 48 std. cc/sec into the test chamber. An effort was made to simulate propellant system flow dynamics corresponding to actual spacecraft mission use. Fast time response liquid flow rate measurements showed that large variations occurred in the ratio of oxidizer to fuel flow for pulse-on times up to 120 msec. These variations could lead to poor combustion efficiency and the production of contamination.

Cassidy, J. F.↗
NASA NTRS1971

The effect of rocket plume contamination on the optical properties of transmitting and reflecting materials

The preliminary results of plume contamination from a 5-pound thrust single-doublet, bipropellant rocket engine on the transmittance of quartz and the reflectance of a silicon monoxide overcoated aluminum mirror are presented. Changes in quartz transmittance were found to be significant and were due to both absorption and scattering effects. Contaminant absorption effects were predominant at the short wavelengths and scattering effects were greatest in the visible wavelengths. Measured changes in mirror reflectance were due primarily to contaminant absorption. Scattering effects were found to be as much as 9 percent of the total reflected energy from the mirror. There were no noticeable chemical or erosion effects on either the quartz or the front surface mirror.

Jack, J. R.↗
NASA NTRS1970

Measurement of surface roughness slope

Instrument, consisting of isolator, differentiator, absolute value circuit, and integrator, uses output signal from surface texture analyzer profile-amplifier to calculate surface roughness slope. Calculations provide accurate, instantaneous value of the slope. Instrument is inexpensive and applicable to any commerical surface texture analyzer.

Cassidy, J. F.↗