Search NASA⌕ Search

Engineering topics

Caveny, L. H.

Publications and source records attributed to Caveny, L. H..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Thrust and ignition transients of the Space Shuttle solid rocket motor

Techniques developed for predicting and analyzing ignition, pressurization, and thrust transients in large segmented motors were applied to the four developmental Space Shuttle solid rocket motors. Following the first test, attention was focused on understanding dynamic thrust and the rate of thrust increase during pressurization and predicting effects of reduced igniter mass flow rate and gas temperature. The close coupling between the igniter and the head-end segment and the high length-to-diameter ratio make understanding of the longitudinal pressure waves essential. The igniter performance along with igniter to head-end segment geometry govern the induction interval and head-end segment ignition. Following ignition of the head-end segment, subsequent flame spreading and pressurization tend to be motor properties which are not appreciably altered by changes in the head-end igniter mass flow rate.

Caveny, L. H.↗
NASA NTRS1979

Evaluation of candidate metals in a simulated space shuttle main engine environment for application as turbine blade dampers

The high-pressure pumps for the space shuttle main engine are driven by combustion products which are 50 percent H2 and 50 percent H2O (by weight). The Haynes alloy 188, used in the dampers, experienced erosion. The erosion producing characteristics of wet H2 were evaluated using a controlled environment produced by a ballistic compressor. Four candidate materials were evaluated: H-188, A-286, Pt/Rh and Rh. Rh was clearly the most erosion resistant. Comparisons with AISI 4340 and Fe specimens of known uniformity indicate that metallurgical defects in the candidate materials are primary contributors to the higher than usual erosion.

Caveny, L. H.↗
NASA NTRS1978

Extensions to analysis of ignition transients of segmented rocket motors

The analytical procedures described in NASA CR-150162 were extended for the purpose of analyzing the data from the first static test of the Solid Rocket Booster for the Space Shuttle. The component of thrust associated with the rapid changes in the internal flow field was calculated. This dynamic thrust component was shown to be prominent during flame spreading. An approach was implemented to account for the close coupling between the igniter and head end segment of the booster. The tips of the star points were ignited first, followed by radial and longitudinal flame spreading.

Caveny, L. H.↗
NASA NTRS1976

Ignition Transients of Large Segmented Solid Rocket Boosters

A model is described which provides a means for analyzing the complexities of ignition transients and pressure peaks of large, high performance, segmented solid rocket boosters. The method accounts for: (1) temporal and spatial development of the flow field set up by the head end igniter discharge, (2) ignition and flame spreading coupled to chamber flow, (3) the steep velocity, pressure, and temperature gradients that occur during the early phases of ignition, and (4) the interactions that produce ignition spikes (i.e., compression of chamber gases during pressurization, erosive burning, and mass added effect of igniter discharge). The technique differs from earlier models in that the flow interactions between the slots and main chamber are accounted for, and the original computer program for monolithic motors is improved. The procedures were used to predict the ignition transients of the current design for the space shuttle booster.

Caveny, L. H.↗
NASA NTRS1974

Investigation of the starting transients of high performance solid-propellant motors

The starting transients of solid propellant engines were investigated to develop design principles for predicting transients in high performance igniter and engine configurations. Research and diagnosis were conducted on the processes affecting ignition transients, such as heat flux, igniter, flame spreading over the surface, and nonsteady combustion gas dynamics. Abstracts of published reports related to this research are presented. Topics discussed include: development of an analytical model, analytical prediction of the entire ignition transient, transient behavior of pressure and regression rate during reignition after shut-down, and problems associated with restarting hybrid rocket engines.

Summerfield, M.↗
NASA NTRS1973

The starting transient of solid propellant rocket motors with high internal gas velocities

A comprehensive analytical model which considers time and space development of the flow field in solid propellant rocket motors with high volumetric loading density is described. The gas dynamics in the motor chamber is governed by a set of hyperbolic partial differential equations, that are coupled with the ignition and flame spreading events, and with the axial variation of mass addition. The flame spreading rate is calculated by successive heating-to-ignition along the propellant surface. Experimental diagnostic studies have been performed with a rectangular window motor (50 cm grain length, 5 cm burning perimeter and 1 cm hydraulic port diameter), using a controllable head-end gaseous igniter. Tests were conducted with AP composite propellant at port-to-throat area ratios of 2.0, 1.5, 1.2, and 1.06, and head-end pressures from 35 to 70 atm. Calculated pressure transients and flame spreading rates are in very good agreement with those measured in the experimental system.

Peretz, A.↗
NASA NTRS1973

Restart transients of hybrid rocket engines.

Experimental investigation of the problems associated with restarting hybrid rocket motors (i.e., motors wherein a liquid or gaseous oxidizer is injected into the port of a solid fuel grain with subsequent mixing and combustion of the oxidizer and fuel) following a brief period of extinguishment. The results include the finding that the ignition delay on restart is decreased because less energy is absorbed by the fuel before the surface reaches the ignition point.

Saraniero, M. A.↗
NASA NTRS1970

Combustion anomalies in stop-restart firing of hybrid rocket engines

An experimental investigation of the restart process of an oxygen-Plexiglas hybrid rocket demonstrated that preheating the fuel (as a consequence of a previous ignition and a temporary extinguishment) significantly increases the rate of chamber pressurization and produces regression rate overshoots during reignition. Higher rates of chamber pressurization measured during the restart transient imply faster instantaneous regression rates of the fuel during restart. Transient periods following the initial ignition and the restart after a two-second shutdown were observed for four experimental tests. Thermocouples were embedded in the fuel to record subsurface temperature histories. A mathematical model of the thermal processes in the fuel and the events that occur during an experimental firing was developed to calculate the regression rate transients. Quantitative agreement with experimental results was obtained by making nominal corrections to the calculated convective and radiative heating rates.

Saraniero, M. A.↗