New Directions: NASA's Airspace Operations and Safety Program
Overview briefing of Airspace Operations and Safety Program (AOSP) and Airspace Technology Demonstration (ATD) project.
Technology Demonstration↗
Engineering topics
Cavolowsky, John A.
Publications and source records attributed to Cavolowsky, John A..
Experimental Demonstration of the Use of a N2O/N2 Mixture in the Driven Tube of a Reflected Shock Tunnel in Order to Increase Test Time
An experimental investigation was carried out into the replacement of air in the driven tube of a reflected shock tunnel by an N2O/N2 mixture in order to increase the test time. The incident shock velocities were between 2 and 3 km/sec. Test times were estimated from light emission histories in the driven tube (at distance of L/D = 46.5 from the main diaphragm) and in the nozzle at an area ratio of 27.9 and from pressure histories just upstream of the nozzle entrance (at L/D = 54). The test times estimated from the light emission histories in the driven tube showed that consistent increases of 60-100% were obtained upon substituting N2O/N2 for air in the driven tube. These increases were in very good agreement with theoretical estimates. The test times estimated from the light emission histories in the nozzle or pressure histories at the nozzle inlet showed significant improvements with N2O/N2 only for cases where the facility was operated at substantially overtailored conditions. It is believed that this is due to the greater stability of the driver-driven interface at overtailored operating conditions. At overtailored operating conditions, test times increases of 60-100% with N2O/N2 were observed with all three diagnostic techniques. These increases were in reasonable agreement with theoretical estimates.
Bogdanoff, David W.↗
A Detailed Level Kinetics Model of NO Vibrational Energy Distributions
Several contemporary problems have pointed to the desirability of a detailed level kinetics approach to modeling the distribution of vibrational energy in NO. Such a model is necessary when vibrational redistribution reactions are insufficient to maintain a Boltzmann distribution over the vibrational energy states. Recent calculations of the rate constant for the first reaction of the Zeldovich mechanism (N2 + O (goes to) NO + N) have suggested that the product NO is formed in high vibrational states. In shock layer flowfields, the product NO molecules may experience an insufficient number of collisions to establish a Boltzmann distribution over vibrational states, thus necessitating a level kinetics model. In other flows, such as expansions of high temperature air, fast, near-resonance vibrational energy exchanges with N2 and O2 may also require a level specific model for NO because of the relative rates of vibrational exchange and redistribution. The proposed report will integrate computational and experimental components to construct such a model for the NO molecule.
Sharma, Surendra P.↗
On Kinetics Modeling of Vibrational Energy Transfer
Two models of vibrational energy exchange are compared at equilibrium to the elementary vibrational exchange reaction for a binary mixture. The first model, non-linear in the species vibrational energies, was derived by Schwartz, Slawsky, and Herzfeld (SSH) by considering the detailed kinetics of vibrational energy levels. This model recovers the result demanded at equilibrium by the elementary reaction. The second model is more recent, and is gaining use in certain areas of computational fluid dynamics. This model, linear in the species vibrational energies, is shown not to recover the required equilibrium result. Further, this more recent model is inconsistent with its suggested rate constants in that those rate constants were inferred from measurements by using the SSH model to reduce the data. The non-linear versus linear nature of these two models can lead to significant differences in vibrational energy coupling. Use of the contemporary model may lead to significant misconceptions, especially when integrated in computer codes considering multiple energy coupling mechanisms.
Gilmore, John O.↗
The Use of Steady and Unsteady Detonation Waves for Propulsion Systems
Detonation wave enhanced supersonic combustors such as the Oblique Detonation Wave Engine (ODWE) are attractive propulsion concepts for hypersonic flight. These engines utilize detonation waves to enhance fuel-air mixing and combustion. The benefits of wave combustion systems include shorter and lighter engines which require less cooling and generate lower internal drag. These features allow air-breathing operation at higher Mach numbers than the diffusive burning scramjet delaying the need for rocket engine augmentation. A comprehensive vehicle synthesis code has predicted the aerodynamic characteristics and structural size and weight of a typical single-stage-to-orbit vehicle using an ODWE. Other studies have focused on the use of unsteady or pulsed detonation waves. For low speed applications, pulsed detonation engines (PDE) have advantages in low weight and higher efficiency than turbojets. At hypersonic speeds, the pulsed detonations can be used in conjunction with a scramjet type engine to enhance mixing and provide thrust augmentation.
Adelman, Henry G.↗
Vibrational Energy Coupling in Expanding N2/O2/NO Admixtures
Recent direct measurements of N2 and O2 vibrational populations in expansions of synthetic air show a closer coupling of the vibrational energies than indicated by adapting earlier experimental results from shock compressions to the nozzle expansion problem. An important difference between the shock wave and nozzle flow problems is the presence of NO in significant amounts throughout the relaxation in the case of a nozzle flow. This may account for the stronger coupling since NO is well suited to promote vibrational energy exchange. The results of a series of experiments and analysis examining vibrational energy coupling in expansions of admixtures approximating air are reported. N2 and O2 vibrational populations are determined by a single-pulse spontaneous Raman scattering technique. NO vibrational populations are determined by broadband absorption by the NO(y) system. The resulting data permit the role of NO in promoting vibrational energy coupling to be better understood, and are used to evaluate models of vibrational energy exchange for application to expanding flows.
Gilmore, John O.↗
Estimates of Heat Shielding Requirements for Saturn Probe Missions
Entry trajectories, decelerations, heating and heat shielding requirements of probes entering the atmosphere of Saturn at relative entry velocities ranging from 26.5 - 33.0 km/sec were studied. Much of the Galileo Jupiter probe technology was applicable to these outer planet probes; therefore, the same configuration was used. A wide range entry flight path angles were used in the trajectory analysis in order to satisfy the complete range of arrival conditions and trajectory requirements. Various entry probe sizes and a range of entry masses from 32 - 258 kg were considered. The carbon phenolic heat shield material used on the Galileo and the successful Pioneer-Venus probes was selected. Turbulent boundary layer convection dominated the heating of the Saturn probes; radiative heating was negligible by comparison at the entry velocities considered. The peak heating rates were found to be about 4 kW per square centimeter, or approximately 17% of the Galileo probe's expected maximum value. The forebody heat shield mass fractions for the Saturn probes were found to vary from about 0.18 to 0.28. By comparison, the Pioneer-Venus probes' heat shield mass fractions ranged from 0.10 to 0.13 and the Galileo probe's forebody value is 0.43.
Wercinski, P.↗
Calibration and Application of Plume Radiation Code: PARRAD
The next generation of Reusable Launch Vehicle (RLV) design requires careful considerations towards Thermal Protection System (TPS) not only in the high-heating regions, also in the base region. The use of hydrocarbon based liquid propulsion engine and the construction, launch and operational cost limitations places a significant burden on the base region TPS design. The radiation from the rocket-plume is expected to dominate base heating during ascent. The objective of this paper is to evaluate the accuracy of a plume radiation modeling with the PARRAD code. The original PARRAD code has been modified to work with single and multiple /overset grids and plume-field solution generated by computational codes, such as GASP. These modifications will be detailed in the proposed paper. To establish accuracy, simulations of the Space Shuttle Main Engine nozzle were performed and the radiative heating predicted by PARRAD are compared with ground based measurements. These results and pertinent discussion of issues related to accuracy will be detailed. In addition, predictions for the X-34 RLV, yet to be performed, will be presented and the significance (or lack) of base heating due to plume radiation will be discussed.
Venkatapathy, Ethiraj↗
Aerothermodynamic Facilities And Measurement: Flow Characterization in Shock Tunnels
This presentation will examine the key performance aspects of shock tunnels as they relate to their use as aerothermodynamic flow simulation facilities. Assessment of shock tube reservoir conditions and flow contaminants generated in the shock tube will be presented along with their limiting impact on viable test envelopes, Facility nozzle performance as it pertains to test time assessment and nozzle exit flow quality (survey of pressure, temperature, and species) will be addressed. Also included will be a discussion of free stream flow diagnostics, both intrusive and nonintrusive, for measurement of critical flow properties not directly inferred from surface mounted transducers. The use of computational fluid dynamics for purposes of validating experimental measurements as well as predicting performance in regimes where measurements are not feasible or possible will be discussed. The use of CFD for facility research and design will also be presented.
Cavolowsky, John A.↗
Results of the NASP Ames Integrated Mixing Hypersonic Engine (AIMHYE) Scramjet Test Program
This paper describes the test techniques and results from the National Aerospace Plane Government Work Package 53, the Ames Integrated Mixing Hypersonic Engine (AIMHYE) Scramjet Test program conducted in the NASA Ames 16-Inch Combustion Driven Shock Tunnel. This was a series of near full-scale scramjet combustor tests with the objective to obtain high speed combustor and nozzle data from an engine with injector configurations similar to the NASP E21 and E22a designs. The experimental test approach was to use a large combustor model (80-100% throat height) designed and fabricated for testing in the semi-free jet mode. The conditions tested were similar to the "blue book" conditions at Mach 12, 14, and 16. GWP 53 validated use of large, long test time impulse facilities, specifically the Ames 16-Inch Shock Tunnel, for high Mach number scramjet propulsion testing an integrated test rig (inlet, combustor, and nozzle). Discussion of key features of the test program will include: effects of the 2-D combustor inlet pressure profile; performance of large injectors' fueling system that included nozzlettes, base injection, and film cooling; and heat transfer measurements to the combustor. Significant instrumentation development and application efforts include the following: combustor force balance application for measurement of combustor drag for comparison with integrated point measurements of skin friction; nozzle metric strip for measuring thrust with comparison to integrated pressure measurements; and nonintrusive optical fiber-based diode laser absorption measurements of combustion products for determination of combustor performance. Direct measurements will be reported for specific test article configurations and compared with CFD solutions.
Cavolowsky, John A.↗
Scramjet Performance Assessment Using Water Absorption Diagnostics (U)
Simultaneous multiple path measurements of temperature and H2O concentration will be presented for the AIMHYE test entries in the NASA Ames 16-Inch Shock Tunnel. Monitoring the progress of high temperature chemical reactions that define scramjet combustor efficiencies is a task uniquely suited to nonintrusive optical diagnostics. One application strategy to overcome the many challenges and limitations of nonintrusive measurements is to use laser absorption spectroscopy coupled with optical fibers. Absorption spectroscopic techniques with rapidly tunable lasers are capable of making simultaneous measurements of mole fraction, temperature, pressure, and velocity. The scramjet water absorption diagnostic was used to measure combustor efficiency and was compared to thrust measurements using a nozzle force balance and integrated nozzle pressures to develop a direct technique for evaluating integrated scramjet performance. Tests were initially performed with a diode laser tuning over a water absorption feature at 1391.7 nm. A second diode laser later became available at a wavelength near 1343.3 nm covering an additional water absorption feature and was incorporated in the system for a two-wavelength technique. Both temperature and mole fraction can be inferred from the lineshape analysis using this approach. Additional high temperature spectroscopy research was conducted to reduce uncertainties in the scramjet application. The lasers are optical fiber coupled to ports at the combustor exit and in the nozzle region. The output from the two diode lasers were combined in a single fiber, and the resultant two-wavelength beam was subsequently split into four legs. Each leg was directed through 60 meters of optical fiber to four combustor exit locations for measurement of beam intensity after absorption by the water within the flow. Absorption results will be compared to 1D combustor analysis using RJPA and nozzle CFD computations as well as to data from a nozzle metric balance measuring thrust and integrated pressure measurements along the length of the nozzle. Assessment of its value as a combustor performance evaluation tool will be conducted.
Cavolowsky, John A.↗
Laser absorption measurements of OH concentration and temperature in pulsed facilities
Explore the source record for details and available documents.
Cavolowsky, John A.↗
Laser absorption flow diagnostics for use in hypersonic ground-based and flight experiments
Consideration is given to laboratory ground-based scale systems for measuring OH and NO and diode laser systems for measuring O2 and H2O. Several diagnostic instruments which are currently being used in a scramjet combustor test rig of the Ames 16-inch shock tunnel are described. Data on mole fraction, temperature, density, pressure, and velocity is obtained using specific data reduction techniques. These measurements provide critical data for evaluation of the propulsion system performance which include mass capture for quantification of fuel equivalence ratio (O2), flow contamination and emission levels (NO), combustion progress (OH), and injector mixing and combustion efficiency (H2O).
Cavolowsky, John A.↗
30 degree injectors at hypervelocity conditions
Results are presented of the first high-speed propulsion-related experiments performed in the NASA-Ames 16-Inch Shock Tunnel, designed to simulate combustor inlet conditions at approximately Mach 14. Results demonstrate the capability of the tunnel for high-speed propulsion testing and yield data on the performance of 30-deg flush wall injectors tested in the tunnel. The experimental results are compared with those of a CFD analysis.
Loomis, Mark P.↗
Flow characterization in the NASA Ames 16-inch Shock Tunnel
Flow characteristics of NASA's 16-Inch Shock Tunnel are determined for purposes of providing hypersonic propulsion simulation capability. The key tunnel operating parameters are the incident shock speed and reservoir pressure and enthalpy. Flow characteristics of concern are the nozzle exit pressure, temperature, Mach number, Reynolds number, chemical composition, and flow uniformity. Surface mounted gages (for pressure and heat transfer) and nonintrusive optical flow diagnostics (emission and absorption spectroscopy and holographic interferometry) are used to verify tunnel conditions. Experimental measurements are used to validate computational analysis for predicting facility performance, and CFD is used to interpret the free stream optical diagnostic measurements.
Cavolowsky, John A.↗
Laser absorption measurements of OH concentration and temperature in pulsed facilities
A laser absorption flow diagnostic application has been developed at the NASA Ames 16-inch Shock Tunnel for purposes of measuring the thermochemical state of OH in flow environments of interest. Research objectives include the investigation of high temperature, low pressure chemistry pertinent to scramjet combustors and high altitude flight. The system can be operated in either the fixed frequency mode or in the rapid wavelength scanning mode to measure species mole fraction and temperature. Emission diagnostics have been employed to determine shock tunnel flow quality and assist in the proper application of the diagnostic and its data interpretation. Rotational lines in the OH system were probed in the expanding facility nozzle flow, and time-resolved measurements of temperature and mole fraction are provided.
Cavolowsky, John A.↗
Reactivation and upgrade of the NASA Ames 16-Inch Shock Tunnel - Status report
The NASA Ames 16-Inch Shock Tunnel has been reactivated after seventeen years of inactivity. In the years before deactivating the facility, it was operated at enthalpies of 4,700 J/gm and pressures up to 260 atm or at enthalpies of 1900 J/gm over a wide pressure range. Since reactivating, the facility has been operated at enthalpies up to 12,000 J/gm and pressures up to 408 atm. The present paper describes the steps taken in upgrading the facility and summarizes the currently achievable conditions. The selection of the driver gas, the steps taken to improve the driver burn, and the diaphragm opening techniques are described. The pressure and heat flux instrumentation, the optical diagnostics and the data acquisition system are also described.
Bogdanoff, David W.↗
A method of analyzing holographic interferograms of ballistic models in hypersonic free-flight
The objective of this research was to develop a method to extract integrated flowfield density information from finite-fringe interferograms produced with a laser holographic interferometer. This method was applied to two sets of holograms. An aeroassist flight experiment model flown in a mixture of 50 percent air - 50 percent argon and a blunt slender cone flown in air were flown at Mach 14.5 into freestream static pressures of 0.04 and 0.08 atm, respectively. The method of analysis can be separated into two main divisions. The first step is to identify fringes inside the wake in terms of the fringes in the freestream. This is important because refraction effects have obscured the region near the shock such that fringes cannot be followed into the wake region. The second step is to extrapolate the freestream fringes into the wake to determine the location of disturbance-related fringe shifts. Coupled with assumptions about the shape of the wake region, the locations of the disturbance-related fringe shifts can be related to the integrated density.
Kieffer, Douglas L.↗