Search NASA⌕ Search

Engineering topics

Cecon, Victor S.

Publications and source records attributed to Cecon, Victor S..

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Utilization of Ultrasonication as a Method of Reducing Organic and Inorganic Contamination in Post‐Consumer Plastic Film Waste

Post-consumer plastic film waste often carries organic and inorganic contaminants that challenge recycling processes and affect the quality of recycled products. An effective contaminant removal procedure through washing such single-used plastic films (SUPFs) can address environmental and waste management concerns. This study compares the efficiency of different washing techniques in reducing SUPF contamination. To evaluate the efficacy of each washing technique, film samples collected from material recovery facilities are individually exposed to friction, ultrasonic-assisted, and a combination of both washes. Thermal analysis indicates that the polymers' melting temperature, crystallization temperature, and crystallinity remain unaffected by the washing methods, demonstrating method aptness. Confocal laser scanning microscope images show that washing results in a cleaner sample surface. 91% ash reduction during the combined wash treatment indicates a high method efficiency compared to the individual friction and ultrasonic wash procedures. This is further validated by reducing characteristic contaminant IR bands (3600–3000, 1750–1600, and 1100–1000 cm −1 ). Elements of concern such as Cd, Cr, Hg, and Pb in SUPFs after each washing technique applied conform with regulations (<100 ppm) for packaging products. This research shows the novel ultrasonic washing reduces more contamination than friction with shorter wash times and no surfactants.

42 ENGINEERING↗
DOE OSTI2024

The Effects of Polyolefin Structure and Source on Pyrolysis-Derived Plastic Oil Composition

Seven types of plastics were pyrolyzed in a fluidized bed reactor: post-consumer recycled (PCR) high-density polyethylene (HDPE), PCR polypropylene (PP), virgin resins of varying molecular weights of HDPE, virgin resins of low-density polyethylene (LDPE), linear low-density polyethylene (LLDPE), and (PP). Pyrolysis produced non-condensable gases (C1-C3), liquid phase products (C4-C40), and solids (C40+ and chars), with alkane, alkene, alkadiene, aromatic, and multi-cycloaromatics as the predominant compounds. Polymer structure had the greatest impact on product distribution, with minimal influence from molecular weight. Branches in polyethylene (PE) acted as thermal defects initiating degradation. Higher branch density in PE led to increased concentrations of aromatics, branched alkanes, and internal alkenes. PP and PE exhibited distinct degradation mechanisms, with PP requiring less energy for decomposition and yielding more oil. Here, pyrolysis oil from PCR HDPE and PCR PP contained a higher proportion of branched compounds. Additives in PCR plastics may promote isomerization during pyrolysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Aliphatic Amines from Waste Polyolefins by Tandem Pyrolysis, Hydroformylation, and Reductive Amination

Pyrolysis of waste plastics can produce a product mixture with a high concentration of olefins (>50 wt%). The olefins, as building blocks in the petroleum industry, are potential precursors for valuable commodity chemicals with higher values (>$2000 per ton). In this work, we produce aldehydes by hydroformylation of the olefins present in pyrolysis oil from colored post-consumer recycled high-density polyethylene (PCR-HDPE). The obtained aldehydes in the oil are then converted into aliphatic amines via reductive amination with a Ru/C catalyst. The aminated oil was characterized by multiple analytical chemistry techniques including elemental analysis, nuclear magnetic resonance spectroscopy, high-resolution liquid chromatography-mass spectrometry, and gas chromatography-mass spectrometry with a Polyarc flame ionization detector. The concentration of metals in the PCR-HDPE and oil changes during the tandem processes, showing limited effects of these elements (e.g., Al, Ca, Fe, Mg, Ti, Zn) on hydroformylation and reductive amination. Additionally, we demonstrated that reductive amination of aldehydes with varied carbon numbers and branching properties can be achieved in the presence of a complex mixture, including paraffins and aromatics. The results indicate that waste plastics have the potential to serve as a renewable source for mono and di aliphatic amines, thereby diminishing reliance on fossil feedstocks as the current primary amine source.

aliphatic amines↗
DOE OSTI2024

Increasing pyrolysis oil yields and decreasing energy consumption via thermal oxo-degradation of polyolefins

Commercialization of pyrolysis of plastics in an inert atmosphere is challenging due to large thermal requirements. This study employs thermal oxo-degradation and demonstrates how oxygen supplied at modest equivalence ratios can both accelerate depolymerization and provide the enthalpy for pyrolysis without dramatically impacting desired product yields. The enthalpies for pyrolysis of high-density polyethylene (HDPE) and polypropylene (PP) are measured to be 2,300 ± 90 J g – -1 and 2,800 ± 60 J g –1 , respectively. Using air as an oxygen source in a fluidized bed reactor, HDPE and PP are rapidly deconstructed while using up to 84% less energy through the energy released by partial oxidation. Characterization of the thermal oxo-degradation product oil shows comparable composition to conventional pyrolysis oil. Thermal oxo-degradation proves to be a promising technology for upcycling of plastics by improving thermal depolymerization of waste plastics and reducing energy requirements while maintaining desirable yields.

42 ENGINEERING↗
DOE OSTI2024

Catalytic conversion of post-consumer recycled high-density polyethylene oil over Zn-impregnated ZSM-5 catalysts

The catalytic conversion of post-consumer recycled high-density polyethylene (PCR-HDPE) pyrolysis oil was investigated using modified ZSM-5 zeolites, prepared under different conditions. The PCR-HDPE oil, obtained through pyrolysis at 500 °C followed by distillation at 165 °C, contained a naphtha fraction hydrocarbons suitable for catalytic upgrading. H/ZSM-5 converts PCR-HDPE naphtha fraction oil primarily into BTX, along with light paraffins and olefins. Introducing mesoporosity led to increased propylene yield at the expense of BTX. Zn impregnation onto H/ZSM-5 and H-meso/ZSM-5 enhanced BTX yield by up to 13 %. However, Zn-meso/ZSM-5 exhibited a lower BTX yield than Zn/ZSM-5 with the same Zn loadings, especially after additional steam treatment at 700 °C. Spent catalysts revealed no noticeable increase in metal contaminants such as calcium and aluminum that were present in the PCR-HDPE. Here, the Zn/ZSM-5 catalyst was stable for more than 50 h time on stream and showed promising potential for upgrading PCR-HDPE naphtha fraction oils.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Evaluation of mixed #3–7 plastic waste from material recovery facilities (MRFs) in the United States

Plastic recycling rates are still low in the United States (U.S.), with less than 10% of municipal solid waste (MSW) plastic being recycled. Most unrecycled plastics are identified by Resin Identification Codes (RIC) from #3–7, which are commonly destined for landfill or waste-to-energy facilities (WTE). Therefore, the composition and quality of outbound bales containing #3–7 plastics were assessed to understand the potential to increase recycling rates. Three bales were sourced from three different Material Recovery Facilities (MRFs) located in the United States. Each bale was manually sorted and characterized for quality and performance via multiple plastic characterization techniques. Considerable differences in bale composition were observed between MRFs, which correlated with the technology used by each MRF in the sorting process. The differences were substantial in the residual levels of poly(ethylene terephthalate) (PET) and high-density polyethylene (HDPE), which are highly desired for mechanical recycling processes and not expected in #3–7 plastics bales. Traditional recycling processes including washing, extrusion, and injection molding of the sorted material were employed prior to the physical, thermal, and molecular characterization. Despite differences in bale composition by plastic type, some polymer properties were similar across MRFs. Here, this research suggests that landfill-diverted mixed plastic waste can be utilized in the mechanical recycling of currently unrecycled materials, as processes can be designed to work with consistent polymer properties. It also highlights the need to upgrade the sorting systems to prevent waste feedstocks, which can be recycled with current technologies, from contaminating other plastic streams or reach landfills.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Recycling of a post-industrial printed multilayer plastic film containing polyurethane inks by solvent-targeted recovery and precipitation

The recently reported Solvent-Targeted Recovery And Precipitation (STRAP) strategy is used to deconstruct multilayer plastic packaging films into their constituent resins by selective polymer dissolution. To broaden the applicability of STRAP, we demonstrate the process with a flexible post-industrial printed multilayer plastic film used for food packaging. The material was a reverse printed film composed of polyethylene (PE), ethylene vinyl alcohol (EVOH), polyethylene terephthalate (PET), and polyurethane (PU)-based inks. Removal of all colors was observed with biomass-derived gamma-valerolactone (GVL) and the recovered polymers possessed comparable properties to the corresponding virgin resins. A technoeconomic analysis indicates that this STRAP process could be economically feasible at a processing capacity of 6,000 tons per year. Furthermore, the production of plastic films with materials recovered by this STRAP process can have a lower climate change impact than the production of films from virgin polymers.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

High-purity Polypropylene from Disposable Face Masks via Solvent-Targeted Recovery and Precipitation

The high use of disposable face masks since the start of COVID-19 has globally generated 4.68–6.24 million tons per year of waste from personal protective equipment. Disposable face masks are generally disposed of in landfills. Polypropylene (PP) is the main component in face masks, which is one of the least recycled plastics but has a high market value. In this work, we extract high-quality PP from face masks using solvent-targeted recovery and precipitation (STRAP) with 90 wt% recovery. N,N-Dimethylacetamide removed the color from the recovered PP to produce a clear high-purity PP, as verified by CIELAB color space. The decolored PP shows similar thermochemical properties and color to virgin PP resin. Here, a techno-economic analysis of the process indicates that high-purity PP recovery can be economically viable at a scale of 5000 tons per year or higher.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A Study on Recycled Polymers Recovered from Multilayer Plastic Packaging Films by Solvent–Targeted Recovery and Precipitation (STRAP)

Multilayer plastic film use increased in multiple packaging applications due to its versatility and overall increased performance over monolayer structures. However, the performance gains from multiple layers also make recycling difficult because they contain multiple polymers that can be immiscible and burdensome to traditional mechanical recycling operations. A possible solution is the solvent-targeted recovery and precipitation (STRAP) process, but the effect on the retrieved polymer is still unknown. Here, the STRAP process is applied to two different multilayer films and samples of recovered polymers are evaluated for physical, molecular, and thermal properties. Changes in the molecular weight are not significant, but differences in thermal properties are reported along with the coprecipitation of different polymers. Solvent retention in the polymer matrix from STRAP reduced the glass transition temperature of samples, but enhanced drying recovered it. Heavy metals, such as Cd, Cr, and Pb are not detected, indicating regulatory compliance for different applications.

36 MATERIALS SCIENCE↗