Search NASA⌕ Search

Engineering topics

Celik, Z. Z.

Publications and source records attributed to Celik, Z. Z..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Experimental study of vortex breakdown in a cylindrical, swirling flow

The stability of a steady, vortical flow in a cylindrical container with one rotating endwall has been experimentally examined to gain insight into the process of vortex breakdowwn. The dynamics of the flow are governed by the Reynolds number (Re) and the aspect ratio of the cylinder. Re is given by Omega R(sup 2)/nu, where Omega is the speed of rotation of the endwall, R is the cylinder radius, and nu is the kinematic viscosity of the fluid filling the cylinder. The aspect ratio is H/R, where H is the height of the cylinder. Numerical simulation studies disagree whether or not the steady breakdown is stable beyond a critical Reynolds number, Re(sub c). Previous experimental researches have considered the steady and unsteady flows near Re(sub c), but have not explored the stability of the steady breakdown structures beyond this value. In this investigation, laser induced fluorescence was utilized to observe both steady and unsteady vortex breakdown at a fixed H/R of 2.5 with Re varying around Re(sub c). When the Re of a steady flow was slowly increased beyond Re(sub c), the breakdown structure remained steady even though unsteadiness was possible. In addition, a number of hysteresis events involving the oscillation periods of the unsteady flow were noted. The results show that both steady and unsteady vortex breakdown occur for a limited range of Re above Re(sub c). Also, with increasing Re, complex flow transformations take place that alter the period at which the unsteady flow oscillates.

Stevens, J. L.↗
NASA NTRS1995

Roll-yaw control at high angle of attack by forebody tangential blowing

The feasibility of using forebody tangential blowing to control the roll-yaw motion of a wind tunnel model is experimentally demonstrated. An unsteady model of the aerodynamics is developed based on the fundamental physics of the flow. Data from dynamic experiments is used to validate the aerodynamic model. A unique apparatus is designed and built that allows the wind tunnel model two degrees of freedom, roll and yaw. Dynamic experiments conducted at 45 degrees angle of attack reveal the system to be unstable. The natural motion is divergent. The aerodynamic model is incorporated into the equations of motion of the system and used for the design of closed loop control laws that make the system stable. These laws are proven through dynamic experiments in the wind tunnel using blowing as the only actuator. It is shown that asymmetric blowing is a highly non-linear effector that can be linearized by superimposing symmetric blowing. The effects of forebody tangential blowing and roll and yaw angles on the flow structure are determined through flow visualization experiments. The transient response of roll and yaw moments to a step input blowing are determined. Differences on the roll and yaw moment dependence on blowing are explained based on the physics of the phenomena.

Pedreiro, N.↗
NASA NTRS1995

Roll-Yaw control at high angle of attack by forebody tangential blowing

The feasibility of using forebody tangential blowing to control the roll-yaw motion of a wind tunnel model is experimentally demonstrated. An unsteady model of the aerodynamics is developed based on the fundamental physics of the flow. Data from dynamic experiments is used to validate the aerodynamic model. A unique apparatus is designed and built that allows the wind tunnel model two degrees of freedom, roll and yaw. Dynamic experiments conducted at 45 degrees angle of attack reveal the system to be unstable. The natural motion is divergent. The aerodynamic model is incorporated into the equations of motion of the system and used for the design of closed loop control laws that make the system stable. These laws are proven through dynamic experiments in the wind tunnel using blowing as the only actuator. It is shown that asymmetric blowing is a highly non-linear effector that can be linearized by superimposing symmetric blowing. The effects of forebody tangential blowing and roll and yaw angles on the flow structure are determined through flow visualization experiments. The transient response of roll and yaw moments to a step input blowing are determined. Differences on the roll and yaw moment dependence on blowing are explained based on the physics of the phenomena.

Pedreiro, N.↗
NASA NTRS1991

Experiments On Schemes For Adaptive-Wall Wind Tunnels

Report discusses experimental investigation of various convergence schemes for adaptive-wall wind tunnel. Results show side-wall-pressure measurements used as flow variables yield same unconfined-flow conditions as those obtained by measuring streamwise and perpendicular components of velocity with laser Doppler velocimeter. Justifies use of influence coefficients in one-step and iterative convergence schemes. Also shows with one-step convergence scheme, satisfactory adaptation obtained when number of iterations reduced to one (or sometimes two).

Celik, Z. Z.↗
NASA NTRS1991

A numerical and experimental study of tangential jet blowing applied to bodies at high angles of attack

The effects of tangential jet blowing on the vortical structures developing about the fuselage of a missile or aircraft at high angle of attack are investigated numerically and experimentally. Computations are carried out for fully laminar and fully turbulent flows, and the results are compared with flow visualization data. It is shown that turbulent computations are more accurate in describing the flow behavior. The actuator plane method is shown to be sufficiently accurate in modeling the essential flow physics of a tangential jet.

Font, G. I.↗
NASA NTRS1987

Evaluation of influence coefficient matrices for an adaptive-wall wind tunnel and applications to one-step convergence scheme

Within the framework of ventilated adaptive-wall wind tunnel testing, experiments were conducted to evaluate the influence coefficients from the side-wall pressure distribution, the streamwise velocity distribution, and the vertical velocity distribution on two control surfaces. Consideration is given to the effects of Mach number, superposition, suction, blowing, and the presence of a nonlifting model. It is shown that a single-step convergence scheme reduces the testing time by eliminating the intermediate experimental iterations; however, its success depends on the accuracy of the influence coefficients.

Celik, Z. Z.↗
NASA NTRS1985

Optimization studies for the development of adaptive wall wind tunnel

The development of adaptive wall wind tunnels makes it possible to establish interference-free boundaries in the region of the model. It is, therefore, feasible to simulate free air conditions. However, the amount of total testing time involved in establishing the required conditions and the complexity of the needed instrumentation prevent currently the use of such methods for routine production testing. Optimization studies have been proposed with the objective to find approaches which will make a more extended application of adaptive wall techniques possible. A new 25cm x 11cm adaptive wall test section was designed and installed to carry out some of these studies. Investigations envisaged are related to the development of a one step convergence method to reduce total testing time, and to measurement procedures which will permit a simplification of the instrumentation. Attention is given to the proposed concept, the test section, instrumentation, and the influence coefficients.

Bodapati, S.↗