Search NASA⌕ Search

Engineering topics

Celina, Mathew C.

Publications and source records attributed to Celina, Mathew C..

Accelerated oxidation of epoxy thermosets with increased O 2 pressure

Polymer oxidation is usually accelerated with temperature, which is therefore applied in nearly every experimental approach dealing with predictive materials aging. Because of this simple approach, we may tend to neglect that the effective concentration of oxygen also acts as a rate multiplier for oxidation. Increasing the oxygen partial pressure in an aging environment accelerates oxidation, and while there is often a near proportional increase initially, the effect of additional oxygen usually transitions to a saturation level at some elevated pressure. This has been theoretically described in the general autoxidation scheme and is well recognized. However, for many materials the exact rate behavior under moderately increased oxygen concentration remains to be established. We therefore review epoxy oxidation and offer a broader overview of its behavior under increased O 2 partial pressure. Experimental data are given for a few thermoset materials demonstrating their rate behavior under O 2 partial pressure up to 4 atm, meaning approximately 20 times more than under standard atmospheric conditions. Confirmative evidence suggests that epoxy materials will reach saturation oxidation rates only at significantly higher O 2 partial pressure. In such a high-pressure regime it is theoretically possible to not only accelerate oxidation, but to transition into a condition where O 2 diffusion can be increased without further accelerating the oxidation rate. Finally, this can reduce diffusion limited oxidation effects under specific accelerated aging conditions as a combination of temperature and O 2 partial pressure.

36 MATERIALS SCIENCE↗

In situ characterization of material extrusion printing by near-infrared spectroscopy

Material extrusion printing of reactive resins and inks present a unique challenge due to the time-dependent nature of the rheological and chemical properties they possess. As a result, careful print optimization or process control is important to obtain consistent, high quality prints via additive manufacturing. Here, we present the design and use of a near-infrared (NIR) flow through cell for in situ chemical monitoring of reactive resins during printing. Differences between in situ and off-line benchtop measurements are presented and highlight the need for in-line monitoring capability. Additionally, in-line extrusion force monitoring and off-line post inspection using machine vision is demonstrated. By combining NIR and extrusion force monitoring, it is possible to follow cure reaction kinetics and viscosity changes during printing. When combined with machine vision, the ability to automatically identify and quantify print artifacts can be incorporated on the printing line to enable real-time, artificial intelligence-assisted quality control of both process and product. Together, these techniques form the building blocks of an optimized closed-loop process control strategy when complex reactive inks must be used to produce printed hardware.

36 MATERIALS SCIENCE↗

Diffusion-limited hydrolysis in polymeric materials

Polymer degradation under aggressive environmental stressors often develops heterogeneities due to diffusion-limited reaction phenomena. This is well established for diffusion-limited oxidation (DLO), which is known to occur for most polymeric materials at elevated temperatures but has been less summarized for the conditions of diffusion-limited hydrolysis (DLH). Here, an overview of hydrolysis for several materials and a computational model, analogous to the underlying equations for DLO, able to define this diffusion-reaction system is presented. A systematic study of the influence of various parameters, such as water diffusivity, reaction rate and order, and a more in-depth focus on residual isocyanate hydrolysis in a polymeric methylene diphenyl diisocyanate (pMDI) based polyurethane (PU) foam is given. For this system, we present experimental data for model ‘input’ parameters and discuss predictions for different conditions. We conceptually compare the behavior of diffusion-limited oxidation to that of diffusion-limited hydrolysis (DLH). With the mathematical framework and key material properties presented herein, any DLH phenomena following Fickian diffusion behavior can be understood, modeled, and predicted.

36 MATERIALS SCIENCE↗

Carbonyl Identification and Quantification Uncertainties for Oxidative Polymer Degradation

The most revealing indicator for oxidative processes or state of degraded plastics is usually carbonyl formation, a key step in materials degradation as part of the carbon cycle for man-made materials. Hence, the identification and quantification of carbonyl species with infrared spectroscopy have been the method of choice for generations, thanks to their strong absorbance and being an essential intermediate in carbon oxidation pathways. Despite their importance, precise identification and quantification can be challenging and rigorous fully traceable data are surprisingly rare in the existing literature. An overview of the complexity of carbonyl quantification is presented by the screening of reference compounds in solution with transmission and polymer films with ATR IR spectroscopy, and systematic data analyses. Significant variances in existing data and their past use have been recognized. Guidance is offered how better measurements and data reporting could be accomplished. Experimental variances depend on the combination of uncertainty in exact carbonyl species, extinction coefficient, contributions from neighboring convoluting peaks, matrix interaction phenomena and instrumental variations in primary IR spectral acquisition (refractive index and penetration depth for ATR measurements). In addition, diverging sources for relevant extinction coefficients may exist, based on original spectral acquisition. For common polymer degradation challenges, a relative comparison of carbonyl yields for a material is easily accessible, but quantification for other purposes, such as degradation rates and spatially dependent interpretation, requires thorough experimental validation. All variables featured in this overview demonstrate the significant error margins in carbonyl quantification, with exact carbonyl species and extinction coefficients already being major contributors on their own.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Extended use of face masks during the COVID-19 pandemic - Thermal conditioning and spray-on surface disinfection

The current COVID-19 pandemic has resulted in globally constrained supplies for face masks and personal protective equipment (PPE). Production capacity is limited in many countries and the future course of the pandemic will likely continue with shortages for high quality masks and PPE in the foreseeable future. Therefore, expectations are that mask reuse, extended wear and similar approaches will enhance the availability of personal protective measures. Repeated thermal disinfection could be an important option and likely easier implemented in some situations, at least on the small scale, than UV illumination, irradiation or hydrogen peroxide vapor exposure. In this paper, an overview on thermal responses and ongoing filtration performance of multiple face mask types is provided. Most masks have adequate material properties to survive a few cycles (i.e. 30 min disinfection steps) of thermal exposure in the 75°C regime. Some are more easily affected, as seen by the fusing of plastic liner or warping, given that preferred conditioning temperatures are near the softening point for some of the plastics and fibers used in these masks. Hence adequate temperature control is equally important. As guidance, disinfectants sprayed via dilute solutions maintain a surface presence over extended time at 25 and 37°C. Some spray-on alcohol-based solutions containing disinfectants were gently applied to the top surface of masks. Neither moderate thermal aging (less than 24 h at 80 and 95°C) nor gentle application of surface disinfectant sprays resulted in measurable loss of mask filter performance. Subject to bio-medical concurrence (additional checks for virus kill efficiency) and the use of low risk non-toxic disinfectants, such strategies, either individually or combined, by offering additional anti-viral properties or short term refreshing, may complement reuse options of professional masks or the now ubiquitous custom-made face masks with their often unknown filtration effectiveness.

36 MATERIALS SCIENCE↗

IR spectroscopic quantification of small molecule transport and desorption phenomena in polymers

The application, continued performance, and degradation behavior of polymers often depends on their interaction with small organic or gaseous volatiles. Understanding the underlying permeation and diffusion properties of materials is crucial for predicting their barrier properties (permeant flux), drying behavior, solvent loss or tendency to trap small molecules, as well as their interaction with materials in the vicinity due to off-gassing phenomena, perhaps leading to compatibility concerns. Further, the diffusion of low Mw organics is also important for mechanistic aspects of degradation processes. Based on our need for improved characterization methods, a FTIR-based spectroscopic gas/volatile quantification setup was designed and evaluated for determination of the diffusion, desorption and transport behavior of small IR-active molecules in polymers. At the core of the method, a modified, commercially available IR transmission gas cell monitors time-dependent gas concentration. Appropriate experimental conditions, e.g. desorption or permeation under continuous flow or static gas conditions, are achieved using easily adaptable external components such as flow controllers and sample ampoules. This study presents overview approaches using the same IR detection methodology to determine diffusivity (desorption into a static gas environment, continuous gas flow, or intermittent desorption) and permeability (static and dynamic flow detection). Further, the challenges encountered for design and setup of IR gas quantification experiments, related to calibration and gas interaction, are presented. These methods establish desorption and permeation behavior of solvents (water and methanol), CO 2 off-gassing from foam, and offer simultaneous measurements of the permeation of several gases in a gas mixture (CO 2 , CO and CH 4 ) through polymer films such as epoxy and Kapton. They offer complementary guidance for material diagnostics and understanding of basic properties in sorption and transport behavior often of relevance to polymer degradation or materials reliability phenomena.

36 MATERIALS SCIENCE↗

High temperature polymer degradation: Rapid IR flow-through method for volatile quantification

Accelerated aging of polymers at elevated temperatures often involves the generation of volatiles. These can be formed as the products of oxidative degradation reactions or intrinsic pyrolytic decomposition as part of polymer scission reactions. A simple analytical method for the quantification of water, CO 2 , and CO as fundamental signatures of degradation kinetics is required. Here, we describe an analytical framework and develops a rapid mid-IR based gas analysis methodology to quantify volatiles that are contained in small ampoules after aging exposures. The approach requires identification of unique spectral signatures, systematic calibration with known concentrations of volatiles, and a rapid acquisition FTIR spectrometer for time resolved successive spectra. Furthermore, the volatiles are flushed out from the ampoule with dry N2 carrier gas and are then quantified through spectral and time integration. This method is sufficiently sensitive to determine absolute yields of ~50 μg water or CO 2 , which relates to probing mass losses of less than 0.01% for a 1 g sample, i.e. the early stages in the degradation process. Such quantitative gas analysis is not easily achieved with other approaches. Our approach opens up the possibility of quantitative monitoring of volatile evolution as an avenue to explore polymer degradation kinetics and its dependence on time and temperature.

36 MATERIALS SCIENCE↗

The kinetics of polyurethane structural foam formation: Foaming and polymerization

We are developing kinetic models to understand the manufacturing of polymeric foams, which evolve from low viscosity Newtonian liquids, to bubbly liquids, finally producing solid foam. Closed-form kinetics are formulated and parameterized for PMDI-10, a fast curing polyurethane, including polymerization and foaming. PMDI- 10 is chemically blown, where water and isocyanate react to form carbon dioxide. The isocyanate reacts with polyol in a competing reaction, producing polymer. Our approach is unique, though it builds on our previous work and the polymerization literature. This kinetic model follows a simplified mathematical formalism that decouples foaming and curing, including an evolving glass transition temperature to represent vitrification. This approach is based on IR, DSC, and volume evolution data, where we observed that the isocyanate is always in excess and does not affect the kinetics. Finally, the kinetics are suitable for implementation into a computational fluid dynamics framework, which will be explored in subsequent papers.

36 MATERIALS SCIENCE↗

Gamma Irradiation and Oxidative Degradation of a Silica-Filled Silicone Elastomer

The radiation oxidative degradation of a commonly used silica-filled silicone elastomer DC745 was investigated by a series of experimental techniques. This elastomer is known to be chemically and thermally stable, but insufficient data exist on the radiation resistance. In the present work, gamma doses up to 200 kGy were applied under air at RT and 1Gy/s. Radiation chemical changes were investigated by NMR, FT-IR, Raman, and mass spectroscopy. DSC and TGA experiments probed thermal transitions and thermal stability changes with exposure dose. SEM probed variations on the surface of the elastomer, and solvent swelling methods were used to investigate changes in the polymer network properties. Electron paramagnetic resonance was employed to detect and identify free radicals. Uniaxial compression load tests at variable temperatures were performed to assess changes in the material’s mechanical response as a function of radiation dose. Results demonstrate that, with increasing exposure, DC745 undergoes changes in chemistry that lead to an increase in thermal stability and cross-link density, formation of free radical species, decrease in heat of fusion and increase in stiffness at low temperatures. Taken together, these results indicate that oxidative cross-linking is the dominant radiolysis mechanism that occurs when this material is exposed to gamma irradiation in air at high dose rates.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Review of polymer oxidation and its relationship with materials performance and lifetime prediction

All polymers are intrinsically susceptible to oxidation, which is the underlying process for thermally driven materials degradation and of concern in various applications. There are many approaches for predicting oxidative polymer degradation. Aging studies usually are meant to accelerate oxidation chemistry for predictive purposes. Kinetic models attempt to describe reaction mechanisms and derive rate constants, whereas rapid qualification tests should provide confidence for extended performance during application, and similarly TGA tests are meant to provide rapid guidance for thermal degradation features. What are the underlying commonalities or diverging trends and complications when we approach thermo-oxidative aging of polymers in such different ways? This review presents a brief status report on the important aspects of polymer oxidation and focuses on the complexity of thermally accelerated polymer aging phenomena. Thermal aging and lifetime prediction, the importance of DLO, property correlations, kinetic models, TGA approaches, and a framework for predictive aging models are briefly discussed. An overall perspective is provided showing the challenges associated with our understanding of polymer oxidation as it relates to lifetime prediction requirements.

36 MATERIALS SCIENCE↗