Engineering topics
Celliers, P. M. (ORCID:0000000176001227)
Publications and source records attributed to Celliers, P. M. (ORCID:0000000176001227).
Yield degradation mechanisms for two-shock capsules evaluated through simulations
An investigation of twenty two-shock campaign indirectly driven capsules on the National Ignition Facility was conducted using the xRAGE computer code. The two-shock platform was developed to look at the sensitivity of fuel–ablator mix with shock timing, asymmetry, surface roughness, and convergence on roughly ignition size scale capsules. This platform used CH/CD (plastic/deuterated plastic) shell capsules that were about 685-μm outer radius and filled with D2 or hydrogen-tritium (HT) gas. The experimental radius and velocity vs time, neutron yield, burn averaged ion temperature (Tion), burn width, and self-emission image size were compared to one-dimensional (1D) and two-dimensional (2D) simulations. Our 2D simulations suggest that the mixing of glass from the fill tube was the dominant source of impurity in the gas region of the capsule during burn, along with fuel–ablator mix. The mass of glass mixed in is about 5–10 ng. Our 2D simulations capture most of the yield trends from different degradation mechanisms, and they match the observed burn width and Tion measurements. Our 2D models match all the available data to within 2.5 times the normalized experimental error for 19 of 20 capsules.
Techniques for studying materials under extreme states of high energy density compression
The properties of materials under extreme conditions of pressure and density are of key interest to a number of fields, including planetary geophysics, materials science, and inertial confinement fusion. In geophysics, the equations of state of planetary materials, such as hydrogen and iron, under ultrahigh pressure and density provide a better understanding of their formation and interior structure [Celliers et al., “Insulator-metal transition in dense fluid deuterium,” Science 361, 677–682 (2018) and Smith et al., “Equation of state of iron under core conditions of large rocky exoplanets,” Nat. Astron. 2, 591–682 (2018)]. The processes of interest in these fields occur under conditions of high pressure (100 GPa–100 TPa), high temperature (>3000 K), and sometimes at high strain rates (>103 s−1) depending on the process. With the advent of high energy density (HED) facilities, such as the National Ignition Facility (NIF), Linear Coherent Light Source, Omega Laser Facility, and Z, these conditions are reachable and numerous experimental platforms have been developed. To measure compression under ultrahigh pressure, stepped targets are ramp-compressed and the sound velocity, measured by the velocity interferometer system for any reflector diagnostic technique, from which the stress-density of relevant materials is deduced at pulsed power [M. D. Knudson and M. P. Desjarlais, “High-precision shock wave measurements of deuterium: Evaluation of exchange-correlation functionals at the molecular-to-atomic transition,” Phys. Rev. Lett. 118, 035501 (2017)] and laser [Smith et al., “Equation of state of iron under core conditions of large rocky exoplanets,” Nat. Astron. 2, 591–682 (2018)] facilities. To measure strength under high pressure and strain rates, experimenters measure the growth of Rayleigh–Taylor instabilities using face-on radiography [Park et al., “Grain-size-independent plastic flow at ultrahigh pressures and strain rates,” Phys. Rev. Lett. 114, 065502 (2015)]. The crystal structure of materials under high compression is measured by dynamic x-ray diffraction [Rygg et al., “X-ray diffraction at the national ignition facility,” Rev. Sci. Instrum. 91, 043902 (2020) and McBride et al., “Phase transition lowering in dynamically compressed silicon,” Nat. Phys. 15, 89–94 (2019)]. Medium range material temperatures (a few thousand degrees) can be measured by extended x-ray absorption fine structure techniques, Yaakobi et al., “Extended x-ray absorption fine structure measurements of laser-shocked V and Ti and crystal phase transformation in Ti,” Phys. Rev. Lett. 92, 095504 (2004) and Ping et al., “Solid iron compressed up to 560 GPa,” Phys. Rev. Lett. 111, 065501 (2013), whereas more extreme temperatures are measured using x-ray Thomson scattering or pyrometry. This manuscript will review the scientific motivations, experimental techniques, and the regimes that can be probed for the study of materials under extreme HED conditions.
Fuel convergence sensitivity in indirect drive implosions
In inertial confinement fusion experiments at the National Ignition Facility, a spherical shell of deuterium–tritium fuel is imploded in an attempt to reach the conditions needed for fusion, self-heating, and eventual ignition. Since theory and simulations indicate that ignition efficacy in 1D improves with increasing imploded fuel convergence ratio, it is useful to understand the sensitivity of the scale-invariant fuel convergence on all measurable or inferable 1D parameters. In this paper, we develop a simple isobaric and isentropic compression scaling model incorporating sensitivity to the in-flight adiabat inferred from shock strengths, to measured implosion velocity, and to known initial ablator and fuel aspect ratio and mass ratio. The model is first benchmarked to 1D implosion simulations spanning a variety of relevant implosion designs. We then use the model to compare compressibility trends across all existing indirect-drive layered implosion data from the facility spanning three ablators [CH, carbon (C), and Be], for which in-flight fuel adiabats varied from 1.6 to 5 by varying the number of drive shocks from 2 to 4, peak implosion velocities varied by 1.4×, capsule radii by 50%, and initial fuel aspect ratios by 1.4×. We find that the strength of the first shock is the dominant contributor setting the maximum fuel convergence. We also observe additional sensitivities to successive shock strengths and fuel aspect ratios that improve the agreement between the expected and measured compression for carbon and Be designs with adiabats above 3. A principal finding is that the adiabat 2.5 C-shell designs exhibit less convergence than CH-shell designs of similar inferred in-flight adiabat.
Equation-of-state, sound speed, and reshock of shock-compressed fluid carbon dioxide
Mechanical equation-of-state data of initially liquid and solid CO2 shock-compressed to terapascal conditions are reported. Diamond-sapphire anvil cells were used to vary the initial density and state of CO2 samples that were then further compressed with laser-driven shock waves, resulting in a data set from which precise derivative quantities, including Grüneisen parameter and sound speed, are determined. Reshock states are measured to 800 GPa and map the same pressure-density conditions as the single shock using different thermodynamic paths. The compressibility data reported here do not support current density-functional-theory calculations, but are better represented by tabular equation-of-state models.