Engineering topics

Cezairliyan, A.

Publications and source records attributed to Cezairliyan, A..

6 records

NASA NTRS1993

High-speed spatial scanning pyrometer

A high-speed spatial scanning pyrometer has been designed and developed to measure spectral radiance temperatures at multiple target points along the length of a rapidly heating/cooling specimen in dynamic thermophysical experiments at high temperatures (above about 1800 K). The design, which is based on a self-scanning linear silicon array containing 1024 elements, enables the pyrometer to measure spectral radiance temperatures (nominally at 650 nm) at 1024 equally spaced points along a 25-mm target length. The elements of the array are sampled consecutively every 1 microsec, thereby permitting one cycle of measurements to be completed in approximately 1 msec. Procedures for calibration and temperature measurement as well as the characteristics and performance of the pyrometer are described. The details of sources and estimated magnitudes of possible errors are given. An example of measurements of radiance temperatures along the length of a tungsten rod, during its cooling following rapid resistive pulse heating, is presented.

Cezairliyan, A.↗

NASA NTRS1990

A dynamic technique for measuring surface tension at high temperatures in microgravity environment

The feasibility of a dynamic technique for measuring surface tension of liquid metals at high temperatures in a microgravity environment was demonstrated. The basic method involves heating a tubular specimen resistively from ambient temperature through its melting point in about 1 sec by passing an electrical current pulse through it, while simultaneously recording the pertinent experimental quantities. Static equilibrium for the molten specimen is achieved in a microgravity environment by splitting the current after it passes through the specimen tube and returning a fraction along the tube axis, and the remaining fraction outside the specimen. Adjustments to the current split enable a balance between the magnetic and surface tension forces acting on the specimen. Values for surface tension are determined from measurements of the equilibrium dimensions of the molten specimen tube, and the magnitudes of the currents. Rapid melting experiments, performed during microgravity simulations with the NASA KC-135 aircraft, yield a value for the surface tension of copper at its melting point which is in agreement with literature data. Measurements of surface tension of a refractory metal (tantalum) are underway.

Miiller, A. P.↗

NASA NTRS1990

A high-speed spatial (linear) scanning pyrometer: A tool for diagnostics, temperature mapping, and property determinations at high temperatures

Development of a fast spatial scanning pyrometer for temperature measurements above 1500 K is described. The salient features of the pyrometer are: (1) it measures spectral radiance temperature (at 0.65 micron) at 1024 points along a straight line (25 mm long) on the target; (2) it has no moving parts and uses a self-scanning linear array of silicon photodiodes as the detector; (3) its output is recorded digitally every 1 microsec with a full-scale resolution of about 1 part in 4000, permitting performance of a complete cycle of measurements (1024 points) in about 1 ms. Operational characteristics of the pyrometer are given. Examples of measurements of the temperature along rapidly heated (resistive self-heating) specimens (rod, tube, strip) are presented. Potential use of the pyrometer in the experiments, both ground-based and in microgravity, requiring temperature mapping and property distribution of the specimen at high temperatures is discussed.

Cezairliyan, A.↗

NASA NTRS1989

Dynamic response for thermal control and measurement and fast radiation thermometry

A preliminary evaluation was made by ORNL of a two-color ratio pyrometer (TCRP) for temperature control in the Modular Electromagnetic Levitation (MEL) experiment. A discussion was presented by Eric Spjut at the 1987 NASA Non-Contact Temperature Measurement Workshop (NASA Conf. Publ. 2503, pp. 182-213) in which he described the non-linear characteristics of the time response of TCPs. Researchers replicated his model and results and note that the non-linear response behavior is minimized for small temperature steps at high temperatures. They then used the predicted response in a model for a proportional or integral feedback controller and predicted the control characteristics for heating and cooling a 5-mm diameter sphere of niobium at high (1500 to 2750 K) temperatures. The analysis shows that for a slow (25-ms) time response for a commercial RCRP, overshoots of several hundred kelvins will result from a 100-K decrease in the setpoint, and temperature tracking errors of 14 to 45 K will occur for control temperature ramps of 1000K/s. For a fast (greater than 0.1 ms) time response, the overshoot and ramp response errors are largely eliminated.

Shepard, R. L.↗

NASA NTRS1987

Transient heat transfer and thermophysical properties measurements in low gravity

Theoretical computer models and correlations which describe phenomena important in the design of transient heat transfer systems are verified and extended. Attention is given to heat transfer to a fluid near the thermodynamic critical point, i.e., a highly compressible fluid. The validity of the computer model is tested by conducting heat-transfer experiments in a low gravity environment where gravity-driven motion is essentially eliminated. It is noted that the NASA KC135 aircraft provides a useful low-g platform for experimental work and provides valuable experience and background for experiments ultimately designed to fly on the Space Shuttle.

Giarratano, P. J.↗

NASA NTRS1985

Dynamic Thermophysical Measurements in Space

The objective is to develop techniques for the dynamic measurement of selected thermophysical properties (e.g., heat of fusion, heat capacity, electrical resistivity) of solids and liquids at temperatures above 2000 K in a near zero-gravity environment. The first phase involves establishing the stability (geometrical) limits of specimens when rapidly heated to temperatures beyond their melting point. A test equipment package was designed and constructed for this purpose, consisting of removable specimen cartridge cells, a battery-bank power supply, a high-speed framing camera, a single-wavelength pyrometer, and electronic switching and control equipment. The operation of the equipment package was tested in the laboratory in preparation for near zero-gravity experiments to be performed during a KC-135 flight in September, 1984.

Cezairliyan, A.↗