Engineering topics

Chamis, C. C.

Publications and source records attributed to Chamis, C. C..

At least 145 records · Page 8

NASA NTRS1988

Fracture toughness computational simulation of general delaminations in fiber composites

A procedure is described to computationally simulate composite laminate fracture toughness in terms of strain energy release rate (SERR). It is also used to evaluate the degradation in laminate structural integrity in terms of displacements, loss in stiffness, loss in vibration frequencies and loss in buckling resistance. Specific laminates are selected for detail studies in order to demonstrate the generality of the procedure. These laminates had center delaminations, off-center delaminations, and pocket delaminations (center and off-center) at the free-edge and center delaminations at the interior. The laminates had two different thicknesses and were made from three different materials. The results obtained are presented in graphical form to illustrate the effects of delamination on the laminate structural integrity and on the laminate strain energy release rate (composite fracture toughness).

Murthy, P. L. N.↗

NASA NTRS1988

Parametric studies of advanced turboprops

The effects of geometric variables (sweep and twist) on the structural performance of advanced turboprops are investigated. The investigation is limited to aerodynamically efficient turboprops using an acceptable design configuration as a baseline. The baseline configuration is modified using a seven by seven array of independently varying sweep and twist parameters while maintaining acceptable aerodynamic efficiency. The turboprop structural performance is evaluated in terms of critical speeds, tip displacements, and vibration frequencies where geometric nonlinearities are included. The results obtained are presented in such a manner as to highlight the effects of sweep and twist on the structural performance of aerodynamically efficient turboprop configurations.

Fertis, D. G.↗

NASA NTRS1988

Probabilistic composite micromechanics

Probabilistic composite micromechanics methods are developed that simulate expected uncertainties in unidirectional fiber composite properties. These methods are in the form of computational procedures using Monte Carlo simulation. A graphite/epoxy unidirectional composite (ply) is studied to demonstrate fiber composite material properties at the micro level. Regression results are presented to show the relative correlation between predicted and response variables in the study.

Stock, T. A.↗

NASA NTRS1988

Probabilistic constitutive relationships for cyclic material strength models

A methodology is developed that provides a probabilistic treatment for the lifetime of structural components of aerospace propulsion systems subjected to fatigue. Material strength degradation models, based on primitive variables, include both a fatigue strength reduction model and a fatigue crack growth model. Probabilistic analysis is based on simulation, and both maximum entropy and maximum penalized likelihood methods are used for the generation of probability density functions. The resulting constitutive relationships are included in several computer programs.

Boyce, L.↗

NASA NTRS1988

Superelement methods applications to micromechanics of high temperature metal matrix composites

Adaptation of the superelement finite-element method for micromechanics of continuous fiber high temperature metal matrix composites (HT-MMC) is described. The method is used to predict the thermomechanical behavior of P100-graphite/copper composites using MSC/NASTRAN and it is also used to validate those predicted by using an in-house computer program designed to perform micromechanics for HT-MMC. Typical results presented in the paper include unidirectional composite thermal properties, mechanical properties, and microstresses.

Caruso, J. J.↗

NASA NTRS1988

Hygrothermomechanical fiber composite fatigue - Computational simulation

The technology of advanced fiber composites has matured to the point where these composites are prime contenders for various structural applications. One of the major design considerations for prolonged service of these composites is fatigue due to cyclic hygral (moisture), thermal and mechanical (hygrothermomechanical) loading conditions. Recent research activities at the Lewis Research Center have led to the development of formal procedures for predicting, using computational simulation, fatigue in fiber composites due to cyclic hygrothermomechanical loading conditions. These formal procedures have subsequently been programmed into a computer module and embedded into the Integrated Composites Analyzer (ICAN) computer code. The objective of this paper is to present and describe results obtained using the augmented ICAN computer code.

Ginty, C. A.↗

NASA NTRS1988

A probabilistic approach to composite micromechanics

Stock, T. A.↗

NASA NTRS1988

Fracture toughness computational simulation of general delaminations in fiber composites

A procedure is described to computationally simulate composite laminate fracture toughness in terms of strain energy release rate. It is also used to evaluate the degradation in laminate structural integrity in terms of displacements, loss in stiffness, loss in vibration frequencies and loss in buckling resistance. Specific laminates are selected for detail studies in order to demonstrate the generality of the procedure. These laminates had center delaminations, off-center delaminations, and pocket delaminations (center and off-center) at the free-edge and center delaminations at the interior. The laminates had two different thicknesses and were made from three different materials. The results obtained are presented in graphical form to illustrate the effects of delamination on the laminate structural integrity and on the laminate strain energy release rate (composite fracture toughness).

Wilt, T. E.↗

NASA NTRS1988

Parametric studies of advanced turboprops

Maser, J. G.↗

NASA NTRS1988

Finite element substructuring methods for composite mechanics

Finite element substructuring strategies are presented to obtain numerical solutions for three typical problems of interest to the composites community: (1) impact and toughness characterization of composites using Charpy's impact test specimen; (2) free-edge stress analysis of composite laminates; and (3) fracture toughness predictions of composites for individual and combined fracture of modes I, II, and III. The key issue common to these problems is the presence of singular or near singular stress fields. The regions prone to see steep stress gradients are substructured with progressively refined meshes to study the local response simultaneously with the global response. The results from the select examples indicate that finite element substructuring methods are computationally effective for composite singularity mechanics.

Murthy, P. L. N.↗

NASA NTRS1988

Prediction of high temperature metal matrix composite ply properties

The application of the finite element method (superelement technique) in conjunction with basic concepts from mechanics of materials theory is demonstrated to predict the thermomechanical behavior of high temperature metal matrix composites (HTMMC). The simulated behavior is used as a basis to establish characteristic properties of a unidirectional composite idealized an as equivalent homogeneous material. The ply properties predicted include: thermal properties (thermal conductivities and thermal expansion coefficients) and mechanical properties (moduli and Poisson's ratio). These properties are compared with those predicted by a simplified, analytical composite micromechanics model. The predictive capabilities of the finite element method and the simplified model are illustrated through the simulation of the thermomechanical behavior of a P100-graphite/copper unidirectional composite at room temperature and near matrix melting temperature. The advantage of the finite element analysis approach is its ability to more precisely represent the composite local geometry and hence capture the subtle effects that are dependent on this. The closed form micromechanics model does a good job at representing the average behavior of the constituents to predict composite behavior.

Caruso, J. J.↗

NASA NTRS1987

Free-edge delamination: Laminate width and loading conditions effects

The width and loading conditions effects on free-edge stress fields in composite laminates are investigated using a three-dimensional finite element analysis. This analysis includes a special free-edge region refinement or superelement with progrssive substructuring (mesh refinement) and finite thickness interply layers. The different loading conditions include in-plane and out-of-plane bending, combined axial tension and in-plane shear, twisting, uniform temperature and uniform moisture. Results obtained indicate that: axial tension causes the smallest magnitude of interlaminar free edge stress compared to other loading conditions; free-edge delamination data obtained from laboratory specimens cannot be scaled to structural components; and composite structural components are not likely to delaminate.

Murthy, P. L. N.↗

NASA NTRS1987

Three-dimensional inelastic analysis methods for hot section components

The objective was to develop analytical methods capable of evaluating the cyclic time dependent inelasticity which occurs in hot section engine components. Because of the large excursions in temperature associated with hot section engine components, the techniques developed must be able to accommodate large variations in material behavior including plasticity and creep. To meet this objective, a matrix consisting of three constitutive mode-element formulations was developed. A separate program for each combination of constitutive mode-element model was written. The source codes of the nine programs range in size from 7300 lines for the Bodner/twenty code to 19,000 lines for the Haisler and Allen/nine code. All the codes were given a stand alone capability of performing cyclic nonlinear analysis.

Lackney, Joseph↗

NASA NTRS1987

Strain energy release rates of composite interlaminar end-notch and mixed-mode fracture: A sublaminate/ply level analysis and a computer code

A computer code is presented for the sublaminate/ply level analysis of composite structures. This code is useful for obtaining stresses in regions affected by delaminations, transverse cracks, and discontinuities related to inherent fabrication anomalies, geometric configurations, and loading conditions. Particular attention is focussed on those layers or groups of layers (sublaminates) which are immediately affected by the inherent flaws. These layers are analyzed as homogeneous bodies in equilibrium and in isolation from the rest of the laminate. The theoretical model used to analyze the individual layers allows the relevant stresses and displacements near discontinuities to be represented in the form of pure exponential-decay-type functions which are selected to eliminate the exponential-precision-related difficulties in sublaminate/ply level analysis. Thus, sublaminate analysis can be conducted without any restriction on the maximum number of layers, delaminations, transverse cracks, or other types of discontinuities. In conjunction with the strain energy release rate (SERR) concept and composite micromechanics, this computational procedure is used to model select cases of end-notch and mixed-mode fracture specimens. The computed stresses are in good agreement with those from a three-dimensional finite element analysis. Also, SERRs compare well with limited available experimental data.

Valisetty, R. R.↗

NASA NTRS1987

Structural tailoring of advanced turboprops

A computer program has been developed for the performance of numerical optimizations of highly swept propfan blades by minimizing an objective function that is defined either as direct operating cost or the aeroelastic difference between a blade and its scaled model. Three component analysis categories are employed: an optimization algorithm, approximate analysis procedures for objective function and constraint evaluation, and refined analysis procedures for optimum design validation. The analyses conducted by the program encompass aerodynamic efficiency evaluation, finite element stress and vibration analysis, acoustics, flutter, and forced response life prediction.

Brown, K. W.↗

NASA NTRS1986

Design concepts/parameters assessment and sensitivity analyses of select composite structural components

Formal approaches are summarized to evaluate design concepts and perform sensitivity analyses on design parameters of composite structural components for vehicles. The formal approaches include structural analyses coupled with composite micromechanics to assess the structural response of beams made from various intraply hybrids, finite element analysis in conjunction with composite mechanics to assess the structural response of panels made from strip hybrids, and sensitivity analysis through optimization to assess the effects of various design parameters on the optimum design of a panel made from angleplied composite laminates. Results obtained from these approaches are presented in graphical and tabular form to illustrate parametric studies and acceptable ranges of various design parameters.

Chamis, C. C.↗

NASA NTRS1986

Computational engine structural analysis

A significant research activity at the NASA Lewis Research Center is the computational simulation of complex multidisciplinary engine structural problems. This simulation is performed using computational engine structural analysis (CESA) which consists of integrated multidisciplinary computer codes in conjunction with computer post-processing for problem-specific application. A variety of the computational simulations of specific cases are described in some detail in this paper. These case studies include: (1) aeroelastic behavior of bladed rotors, (2) high velocity impact of fan blades, (3) blade-loss transient response, (4) rotor/stator/squeeze-film/bearing interaction, (5) blade-fragment/rotor-burst containment, and (6) structural behavior of advanced swept turboprops. These representative case studies are selected to demonstrate the breath of the problems analyzed and the role of the computer including post-processing and graphical display of voluminous output data.

Chamis, C. C.↗

NASA NTRS1986

Intraply Hybrid Composite Design

Several theoretical approaches combined in program. Intraply hybrid composites investigated theoretically and experimentally at Lewis Research Center. Theories developed during investigations and corroborated by attendant experiments used to develop computer program identified as INHYD (Intraply Hybrid Composite Design). INHYD includes several composites micromechanics theories, intraply hybrid composite theories, and integrated hygrothermomechanical theory. Equations from theories used by program as appropriate for user's specific applications.

Chamis, C. C.↗