Engineering topics

Chang, Clarence T.

Publications and source records attributed to Chang, Clarence T..

At least 19 records

NASA NTRS2020

Emission Characteristics of an Axially Staged Sector Combustor for a Small Core High OPR Subsonic Aircraft Engine

Gaseous (NOx, CO) and non-volatile particulate matter (nvPM) emissions from a small-core high-pressure Axially Controlled Stoichiometry (ACS) combustor are reported. NOx and CO emissions characteristics are similar to a previous version of ACS combustor. Emissions of nvPM at low-power (fuel-rich front end) was found to procude significantly higher nvPM emissions compared to a high-power configuration (fuel-lean front end). NOx emissions for the ACS combustor were 82-89% below the ICAO CAEP/6 standard for aggressive NASA N+3 high-pressure cycles based on NOx correlations developed from experimental measurements.

He, Zhuohui J.↗

NASA NTRS2019

CFD Evaluation of Lean-Direct Injection Combustors for Commercial Supersonics Technology

An overview is given of an effort that focused on using CFD analysis to complement design and configuration definition of Lean-Direct Injection (LDI) combustion concepts for NASA's Commercial Supersonic Transport (CST) program. The National Combustion Code (OpenNCC) was used to perform non-reacting and two-phase reacting flow computations for second and third generation LDI configurations at CST cruise conditions. All computations were performed with a consistent approach of mesh-generation, spray modeling, ignition and kinetics modeling. Emissions (EINOx) characteristics were predicted for CST cruise conditions, and compared with emissions data from experimental measurements to evaluate the fidelity of the CFD modeling approach to predict emissions changes in response to changes in supersonic cycle conditions.

nitrogen oxides injectors↗

NASA NTRS2019

Pilot Injector Redesign to Reduce N+3 Cycle Emissions for a Gas-Turbine Combustor

An overview is given of an effort for the use of CFD analysis to complement design and configuration definition of third generation Lean-Direct Injection combustion concepts (LDI-3) for NASA's N plus 3 program. The National Combustion Code (OpenNCC) was used to perform non-reacting and two-phase reacting flow computations for a three-cup, nineteen-element flametube array with redesigned pilot injectors to improve spray and emissions characteristics when compared to a previous LDI-3 design. All computations were performed with a consistent approach to mesh-generation, spray modeling, ignition and kinetics modeling for a "medium-power" cycle condition. Computational predictions of the aerodynamics of a new pre-filming pilot injector were used to arrive at an optimized aerothermal design that meets effective area and fuel-air mixing criteria. The newly designed pilot injectors were shown to provide considerable improvements in aerodynamic stability, flame-tube pattern factor and NOx emissions, when compared to the original design.

Nitrogen Oxides↗

NASA NTRS2019

CFD Evaluation Of Lean-Direct Injection Combustors for Commercial Supersonics Technology

Ajmani, Kumud↗

NASA NTRS2018

Comparison of Combustion Dynamic Characteristics of Two Advanced Multi-Cup Fuel Injectors

An experimental investigation of the combustion dynamic characteristics of two advanced multi-cup lean direct injectors (LDI) under simulated gas turbine combustor conditions was conducted. The objective was to gain a better understanding of the physical phenomena inside a pressurized flame tube combustion chamber and study the effects of injector flow number on combustion dynamics. The injectors are known as Three-zone Injectors one and two or 3ZI-1 and 3ZI-2, respectively. The injectors were experimentally evaluated at inlet pressures up to 1.724 MPa, non-vitiated air temperatures up to 828K, and adiabatic flame temperatures up to 1975K. Dynamic pressure measurements were taken upstream of the injectors and in the combustion zone. The combustion dynamic behavior of the two injectors was measured over a range of inlet pressures, inlet temperatures, fuel air ratios, and fuel flow splits.

Combustion Dynamics↗

NASA NTRS2018

Fuel Sensitivity of Gas Emissions, Lean Blowout and Combustion Dynamics for a 9-Point LDI Combustor

Fuel sensitivity of gaseous emissions, approach to lean blowout and combustion dynamics are evaluated in this study. Experiments were conducted at the NASA Glenn Research Center's CE-5 flame tube test facility with a 9-point Swirl-Venturi Lean Direct Injection (SV-LDI) combustor. A reference jet fuel (A2) and two test fuels (C1 and C3) from were provided by the National Jet Fuels Combustion Program (NJFCP). C1 is essentially a 2-component iso-paraffin test fuel with a low cetane number of 17, and C3 is a high viscosity test fuel. Approach to lean blowout was monitored in terms of the rapid increase in CO emissions index as equivalence ratio decreased, but testing did not proceed all the way to lean blowout (LBO). Burning C1 was found to produce lower NOx emissions, but C1 flame temperatures were about 25 K higher relative to A2 at near LBO points (where CO emissions increased very rapidly). The NOx emissions of C3 were similar to A2. At low power conditions where fuel injector performance is not optimized for this 9-point LDI combustor, C3 had higher CO emissions than A2 and C1, likely due to C3's higher viscosity relative to A2 and C1. No discernable difference in combustion dynamics was observed between the three fuels tested in the 9-point LDI combustor. While a systematic ignition test campaign was not conducted, it was observed that C1 required a higher equivalence ratio and inlet air temperature for test rig ignition compared to A2 and C3.

Combustion dynamics↗

NASA NTRS2017

Fuel and Combustor Concerns for Future Commercial Combustors

Civil aircraft combustor designs will move from rich-burn to lean-burn due to the latter's advantage in low NOx and nvPM emissions. However, the operating range of lean-burn is narrower, requiring premium mixing performance from the fuel injectors. As the OPR increases, the corresponding combustor inlet temperature increase can benefit greatly with fuel composition improvements. Hydro-treatment can improve coking resistance, allowing finer fuel injection orifices to speed up mixing. Selective cetane number control across the fuel carbon-number distribution may allow delayed ignition at high power while maintaining low-power ignition characteristics.

Combustor↗

NASA NTRS2017

Combustion Dynamic Characteristics Identification in a 9-point LDI Combustor Under Choked Outlet Boundary Conditions

Combustion dynamics data were collected at the NASA Glenn Research Center's CE-5 flame tube test facility under combustor outlet choked conditions. Two 9-point Swirl-Venturi Lean Direct Injection (SV-LDI) configurations were tested in a rectangular cuboid combustor geometry. Combustion dynamic data were measured at different engine operational conditions up to inlet air pressure and temperature of 24.13 bar and 828 K, respectively. In this study, the effects of acoustic cavity resonance, precessing vortex core (PVC), and non-uniform thermal expansion on the dynamic noise spectrum are identified by comparing the dynamic data that collected at various combustor inlet conditions along with combustor geometric calculations. The results show that the acoustic cavity resonance noises were seen in the counter-rotating pilot configuration but not in the co-rotating pilot configuration. Dynamic pressure noise band at around 0.9 kHz was only detected at the P'41 location (9.8 cm after fuel injector face) but not at the P'42 location (29 cm after the fuel injector face); the amplitude of this noise band depended on the thermal expansion ratio (T4/T3). The noise band at around 1.8 kHz was found to depend on the inlet air pressure or the air density inside the combustor. The PVC frequency was not observed in these two configurations.

lean direct injection↗

NASA NTRS2016

Experimental Combustion Dynamics Behavior of a Multi-Element Lean Direct Injection (LDI) Gas Turbine Combustor

An experimental investigation of the combustion dynamic characteristics of a research multi-element lean direct injection (LDI) combustor under simulated gas turbine conditions was conducted. The objective was to gain a better understanding of the physical phenomena inside a pressurized flametube combustion chamber under acoustically isolated conditions. A nine-point swirl venturi lean direct injection (SV-LDI) geometry was evaluated at inlet pressures up to 2,413 kPa and non-vitiated air temperatures up to 867 K. The equivalence ratio was varied to obtain adiabatic flame temperatures between 1388 K and 1905 K. Dynamic pressure measurements were taken upstream of the SV-LDI, in the combustion zone and downstream of the exit nozzle. The measurements showed that combustion dynamics were fairly small when the fuel was distributed uniformly and mostly due to fluid dynamics effects. Dynamic pressure fluctuations larger than 40 kPa at low frequencies were measured at 653 K inlet temperature and 1117 kPa inlet pressure when fuel was shifted and the pilot fuel injector equivalence ratio was increased to 0.72.

dynamics↗

NASA NTRS2016

NASA Low-Emissions Research (And Things Related to Alternative Fuels)

High-level overview of recent NASA low-emissions research in combustor and atmospheric sciences relating to use of alternatively-source fuels.

emissions↗

NASA NTRS2016

Emission Characteristics of A P and W Axially Staged Sector Combustor

Emission characteristics of a three-cup P and W Axially Controlled Stoichiometry (ACS) sector combustor are reported in this article. Multiple injection points and fuel staging strategies are used in this combustor design. Pilot-stage injectors are located on the front dome plate of the combustor, and main-stage injectors are positioned on the top and bottom of the combustor liners downstream. Low power configuration uses only pilot-stage injectors. Main-stage injectors are added to high power configuration to help distribute fuel more evenly and achieve overall lean burn yielding very low NOx emissions. Combustion efficiencies at four ICAO LTO conditions were all above 99%. Three EINOx emissions correlation equations were developed based on the experimental data to describe the NOx emission trends of this combustor concept. For the 7% and 30% engine power conditions, NOx emissions are obtained with the low power configuration, and the EINOx values are 6.16 and 6.81. The high power configuration was used to assess 85% and 100% engine power NOx emissions, with measured EINOx values of 4.58 and 7.45, respectively. The overall landing-takeoff cycle NOx emissions are about 12% relative to ICAO CAEP/6 level.

low NOx comubstor↗

NASA NTRS2015

Low NOx Fuel Flexible Combustor Integration Project Overview

The Integrated Technology Demonstration (ITD) 40A Low NOx Fuel Flexible Combustor Integration development is being conducted as part of the NASA Environmentally Responsible Aviation (ERA) Project. Phase 2 of this effort began in 2012 and will end in 2015. This document describes the ERA goals, how the fuel flexible combustor integration development fulfills the ERA combustor goals, and outlines the work to be conducted during project execution.

emission↗

NASA NTRS2015

NOx Emissions Performance and Correlation Equations for a Multipoint LDI Injector

Lean Direct Injection (LDI) is a combustor concept that reduces nitrogen oxides (NOx) emissions.This paper looks at a 3-zone multipoint LDI concept developed by Parker Hannifin Corporation. The concept was tested in a flame-tube test facility at NASA Glenn Research Center. Due to test facility limitations, such as inlet air temperature and pressure, the flame-tube test was not able to cover the full set of engine operation conditions. Three NOx correlation equations were developed based on assessing NOx emissions dependencies on inlet air pressure (P3), inlet air temperature (T3), and fuel air equivalence ratio(theta) to estimate the NOx emissions at the unreachable high engine power conditions. As the results, the NOx emissions are found to be a strong function of combustion inlet air temperature and fuel air equivalence ratio but a weaker function of inlet air pressure. With these three equations, the NOx emissions performance of this injector concept is calculated as a 66 reduction relative to the ICAO CAEP-6 standard using a 55:1 pressure-ratio engine cycle. Uncertainty in the NOx emissions estimation increases as the extrapolation range departs from the experimental conditions. Since maximum inlet air pressure tested was less than 50 of the full power engine inlet air pressure, a future experiment at higher inlet air pressure conditions is needed to confirm the NOx emissions dependency on inlet air pressure.

NOx correlation equations↗

NASA NTRS2015

NOx Emissions Performance and Correlation Equations for a Multipoint LDI Injector

Lean Direct Injection (LDI) is a combustor concept that reduces nitrogen oxides (NOx) emissions. This paper looks at a 3-zone multipoint LDI concept developed by Parker Hannifin Corporation. The concept was tested in a flame-tube test facility at NASA Glenn Research Center. Due to test facility limitations, such as inlet air temperature and pressure, the flame-tube test was not able to cover the full set of engine operation conditions. Three NOx correlation equations were developed based on assessing NOx emissions dependencies on inlet air pressure (P3), inlet air temperature (T3), and fuel air equivalence ratio (Ф) to estimate the NOx emissions at the unreachable high engine power conditions. As the results, the NOx emissions are found to be a strong function of combustion inlet air temperature and fuel air equivalence ratio but a weaker function of inlet air pressure. With these three equations, the NOx emissions performance of this injector concept is calculated as a 66% reduction relative to the ICAO CAEP-6 standard using a 55:1 pressure-ratio engine cycle. Uncertainty in the NOx emissions estimation increases as the extrapolation range departs from the experimental conditions. Since maximum inlet air pressure tested was less than 50% of the full power engine inlet air pressure, a future experiment at higher inlet air pressure conditions is needed to confirm the NOx emissions dependency on inlet air pressure.

NOx correlation equations↗

NASA NTRS2014

NOx Emissions Performance and Correlation Equations for a Multipoint LDI Injector

Lean Direct Injection (LDI) is a combustor concept that reduces nitrogen oxides (NOx) emissions. This paper looks at a 3-zone multipoint LDI concept developed by Parker Hannifin Corporation. The concept was tested in a flame-tube test facility at NASA Glenn Research Center. Due to test facility limitations, such as inlet air temperature and pressure, the flame-tube test was not able to cover the full set of engine operation conditions. Three NOx correlation equations were developed based on assessing NOx emissions dependencies on inlet air pressure (P3), inlet air temperature (T3), and fuel air equivalence ratio (phi) to estimate the NOx emissions at the unreachable high engine power conditions. As the results, the NOx emissions are found to be a strong function of combustion inlet air temperature and fuel air equivalence ratio but a weaker function of inlet air pressure. With these three equations, the NOx emissions performance of this injector concept is calculated as a 66 percent reduction relative to the ICAO CAEP-6 standard using a 55:1 pressure-ratio engine cycle. Uncertainty in the NOx emissions estimation increases as the extrapolation range departs from the experimental conditions. Since maximum inlet air pressure tested was less than 50 percent of the full power engine inlet air pressure, a future experiment at higher inlet air pressure conditions is needed to confirm the NOx emissions dependency on inlet air pressure.

He, Zhuohui J.↗

NASA NTRS2014

A Second Generation Swirl-Venturi Lean Direct Injection Combustion Concept

A low-NO (sub x) aircraft gas turbine engine combustion concept was developed and tested. The concept is a second generation swirl-venturi lean direct injection (SV-LDI) concept. LDI is a lean-burn combustion concept in which the fuel is injected directly into the flame zone. Three second generation SV-LDI configurations were developed. All three were based on the baseline 9-point SV-LDI configuration reported previously. These second generation configurations had better low power operability than the baseline 9-point configuration. Two of these second generation configurations were tested in a NASA Glenn Research Center flametube; these two configurations are called the at dome and 5-recess configurations. Results show that the 5-recess configuration generally had lower NO (sub x) emissions than the flat dome configuration. Correlation equations were developed for the flat dome configuration so that the landing-takeoff NO (sub x) emissions could be estimated. The flat dome landing-takeoff NO (sub x) is estimated to be 87-88 percent below the CAEP/6 standards, exceeding the ERA project goal of 75 percent reduction.

Tacina, Kathleen M.↗

NASA NTRS2014

High Temperature Dynamic Pressure Measurements Using Silicon Carbide Pressure Sensors

Un-cooled, MEMS-based silicon carbide (SiC) static pressure sensors were used for the first time to measure pressure perturbations at temperatures as high as 600 C during laboratory characterization, and subsequently evaluated in a combustor rig operated under various engine conditions to extract the frequencies that are associated with thermoacoustic instabilities. One SiC sensor was placed directly in the flow stream of the combustor rig while a benchmark commercial water-cooled piezoceramic dynamic pressure transducer was co-located axially but kept some distance away from the hot flow stream. In the combustor rig test, the SiC sensor detected thermoacoustic instabilities across a range of engine operating conditions, amplitude magnitude as low as 0.5 psi at 585 C, in good agreement with the benchmark piezoceramic sensor. The SiC sensor experienced low signal to noise ratio at higher temperature, primarily due to the fact that it was a static sensor with low sensitivity.

Pressure Sensors↗

NASA NTRS2014

NOx Emissions Performance and Correlation Equations for a Multipoint LDI Injector

Lean Direct Injection (LDI) is a combustor concept that reduces nitrogen oxides (NOx) emissions. This paper looks at a 3-zone multipoint LDI concept developed by Parker Hannifin Corporation. The concept was tested in a flame-tube test facility at NASA Glenn Research Center. Due to test facility limitations, such as inlet air temperature and pressure, the flame-tube test was not able to cover the full set of engine operation conditions. Three NOx correlation equations were developed based on assessing NOx emissions dependencies on inlet air pressure (P3), inlet air temperature (T3), and fuel air equivalence ratio (Ф) to estimate the NOx emissions at the unreachable high engine power conditions. As the results, the NOx emissions are found to be a strong function of combustion inlet air temperature and fuel air equivalence ratio but a weaker function of inlet air pressure. With these three equations, the NOx emissions performance of this injector concept is calculated as a 66 percent reduction relative to the ICAO CAEP-6 standard using a 55:1 pressure-ratio engine cycle. Uncertainty in the NOx emissions estimation increases as the extrapolation range departs from the experimental conditions. Since maximum inlet air pressure tested was less than 50 percent of the full power engine inlet air pressure, a future experiment at higher inlet air pressure conditions is needed to confirm the NOx emissions dependency on inlet air pressure.

He, Zhuohui J.↗