Search NASA⌕ Search

Engineering topics

Chang, Ho Chan

Publications and source records attributed to Chang, Ho Chan.

Thermal Conductivity of a Novel Salt-Hydrogel Complex as a Phase Change Material for Building Thermal Management

Use of electricity for space heating, ventilation and air conditioning in buildings may be better managed through temporary energy storage. Compared with electrochemical storage, the levelized cost of thermal energy storage systems can be lower depending on geographical location and thermophysical properties [1]. In any phase change material (PCM), the rate of absorption and release of thermal energy increases with higher thermal conductivity [2]. However, leading PCMs like paraffin waxes have thermal conductivities on the order of 0.1 W/mK. Glauber’s salt, a salt hydrate, possesses a relatively high thermal conductivity but suffers from supercooling and phase segregation. Research has shown that polymer-based composites with salt hydrates can prevent phase segregation and limit supercooling over hundreds of cycles [3] though the thermal conductivity of the composite may be reduced leading to low energy storage rates. Here, we report thermal conductivity measurements on polymer hydrogels which are stable in solutions of Glauber’s salt. To measure thermal conductivity of soft gels, we use a 3-omega method [4] where heat flows bidirectionally through a substrate below and through a gel placed on top. This suits measurements of both gels and liquids unlike transient plane heat source or transient hot wire methods. We report measurements of thermal conductivity of salt-hydrogel complexes as a function of temperature, cross-linking and salt concentration. In addition, we present modeling of thermal conductivity of sodium sulfate solutions with available theories. We finally employ polarized optical microscopy to observe inside the transparent hydrogel networks, showing that precipitating crystals may influence thermal conductivity measurements for high salt concentrations. Our thermal conductivity results combined with enthalpy of phase change, mass density and specific heat are essential to accurately design thermal storage systems for energy-efficient buildings.

composite, thermal conductivity↗

Interpreting T-History Data on Supercooling and Phase Change Enthalpy of a Salt-Hydrogel Complex for Building Thermal Management

Phase change materials (PCMs) are promising materials for storing and discharging latent heat in buildings to regulate the thermal environment. Measurement of salt hydrate PCM thermal performance is often challenging because of supercooling and phase segregation. Though differential scanning calorimetry (DSC) has been widely used to measure thermal properties of various phase change materials, DSC uses milligrams of sample and is unrealistic for predicting large-scale materials performance. The T-history method [1], in contrast, handles higher volumes but the analysis typically requires a lumped capacitance assumption. Here, we report and analyze T-History data on a novel salt-hydrogel complex with high viscosity, that renders low Biot number sample preparation extremely challenging. We re-examine the standard T-history method and compared against DSC data in this complex material. We report details of an experimental setup, built with necessary additions to a controlled environmental chamber. We carefully examine the validity of the lumped capacitance assumption and suggest a modified analysis using a computational approach for reliable data. Experimental parameters such as ramp rate and temperature range of the environmental chamber are considered via computational modeling to understand the effect of ramp rate on supercooling [2]. Finally, we report thermal cycling experiments on the salt-hydrogel complex. Our modified approach to measuring supercooling and enthalpy of fusion at large scales is important in better understanding the performance of phase-change materials at scale for building thermal storage. References: [1] Marin, Jose M, Belen Zalba, Luisa F Cabeza, and Harald Mehling. “Determination of Enthalpy Temperature Curves of Phase Change Materials with the Temperature-History Method: Improvement to Temperature Dependent Properties.” Measurement Science and Technology 14, no. 2 (February 1, 2003): 184–89. https://doi.org/10.1088/0957-0233/14/2/305. [2] Safari, A., R. Saidur, F.A. Sulaiman, Yan Xu, and Joe Dong. “A Review on Supercooling of Phase Change Materials in Thermal Energy Storage Systems.” Renewable and Sustainable Energy Reviews 70 (April 2017): 905–19. https://doi.org/10.1016/j.rser.2016.11.272

thermodynamics↗

High Density Thermal Energy Storage by Highly Stable Glauber’s Salt Composites with Low Supercooling for Building-Scale Application

Phase change materials (PCM) are a promising candidate for thermal energy storage in building infrastructure, enabling grid-integrated peak load shaving by utilizing energy production in off-peak hours. Glauber’s salt (Na2SO4.10H2O, Sodium sulfate hydrate) are highly attractive due to their high energy storage capacity and low cost but Glauber’s salt suffers from long-standing challenges including high supercooling ( > 15oC) and low thermal cyclic stability, which is a major setback for practical building-scale energy storage applications. Here, we developed a unique ionic molecular nucleating agent for Glauber’s salt which reduced the supercooling temperature to less than 5oC. By combining this nucleated SSD with a polymer, phase segregation of salt hydrate for over 100 thermal cycles without degradation was achieved. Key was that the polymer confined the SSD crystals, preventing phase separation. In addition, we applied our stable Glauber’s salt composite in a miniatured building model and demonstrate that our PCM composite can be utilized for real-world building infrastructure.

additives↗

Multi-objective optimization of peel and shear strengths in ultrasonic metal welding using machine learning-based response surface methodology

Ultrasonic metal welding (UMW) is a solid-state joining technique with varied industrial applications. Despite of its numerous advantages, UMW has a relative narrow operating window and is sensitive to variations in process conditions. As such, it is imperative to quantitatively characterize the influence of welding parameters on the resulting joint quality. The quantification model can be subsequently used to optimize the parameters. Conventional response surface methodology (RSM) usually employs linear or polynomial models, which may not be able to capture the intricate, nonlinear input-output relationships in UMW. Furthermore, some UMW applications call for simultaneous optimization of multiple quality indices such as peel strength, shear strength, electrical conductivity, and thermal conductivity. To address these challenges, this paper develops a machine learning (ML)-based RSM to model the input-output relationships in UMW and jointly optimize two quality indices, namely, peel and shear strengths. The performance of various ML methods including spline regression, Gaussian process regression (GPR), support vector regression (SVR), and conventional polynomial regression models with different orders is compared. A case study using experimental data shows that GPR with radial basis function (RBF) kernel and SVR with RBF kernel achieve the best prediction accuracy. The obtained response surface models are then used to optimize a compound joint strength indicator that is defined as the average of normalized shear and peel strengths. In addition, the case study reveals different patterns in the response surfaces of shear and peel strengths, which has not been systematically studied in the literature. While developed for the UMW application, the method can be extended to other manufacturing processes.

42 ENGINEERING↗

Fouling modeling and prediction approach for heat exchangers using deep learning

In this article, we develop a generalized and scalable statistical model for accurate prediction of fouling resistance using commonly measured parameters of industrial heat exchangers. This prediction model is based on deep learning where a scalable algorithmic architecture learns non-linear functional relationships between a set of target and predictor variables from large number of training samples. Here, the efficacy of this modeling approach is demonstrated for predicting fouling in an analytically modeled cross-flow heat exchanger, designed for waste heat recovery from flue-gas using room temperature water. The performance results of the trained models demonstrate that the mean absolute prediction errors are under 10 –4 KW –1 for flue-gas side, water side and overall fouling resistances. The coefficients of determination (R 2 ), which characterize the goodness of fit between the predictions and observed data, are over 99%. Even under varying levels of measurement noise in the inputs, we demonstrate that predictions over an ensemble of multiple neural networks achieves better accuracy and robustness to noise. We find that the proposed deep-learning fouling prediction framework learns to follow heat exchanger flow and heat transfer physics, which we confirm using locally interpretable model agnostic explanations around randomly selected operating points. Overall, we provide a robust algorithmic framework for fouling prediction that can be generalized and scaled to various types of industrial heat exchangers.

42 ENGINEERING↗

Composite Structured Surfaces for Durable Dropwise Condensation

Dropwise condensation of steam on hydrophobic substrates has a 10X higher heat transfer coefficient compared to filmwise condensation. To promote dropwise condensation, low surface energy hydrophobic coatings (polymers) are typically utilized. The low intrinsic thermal conductivity (k < 1 W/(m · K)) of polymers, coupled with high heat transfer coefficient of dropwise condensation (100 kW/(m 2 · K)), necessitates that the coating be thin (< 1µm) in order to avoid reducing the overall heat exchanger conductance. However, thin polymeric films easily degrade. The two opposing requirements result in the need for optimization between the durability (thick coating) and the heat transfer (thin coating). To enable high thermal conductivity in thicker coatings, we develop metal-polymer structured surfaces. By using porous structures as inter-connected heat-conducting backbones that are filled with hydrophobic materials, we enable tuning of the coating effective thermal conductivity and surface energy. Three metal structures were studied; micro/nanowires, inverse opals, and sintered spheres. Heat transfer performance was calculated using three-dimensional finite element method simulations with two distinct boundary conditions; convection at the walls and isothermal walls. Interestingly, the overall conductance shows up to 40% difference depending on the boundary condition used in calculating the composite coating effective thermal conductivity. We use our model to predict the heat transfer performance as a function of metal fraction by volume and by surface area for condensation. By coupling our thermal simulations with a previously verified analytical model for predicting wetting behavior on heterogeneous surfaces, we propose a regime map to predict dropwise-to-filmwise transition. Furthermore, our work not only forms a starting point for the development of durable dropwise condensing surfaces, it identifies important considerations needed for computing effective thermal conductivity of composites.

42 ENGINEERING↗

Extreme Antiscaling Performance of Slippery Omniphobic Covalently Attached Liquids

Scale formation presents an enormous cost to the global economy. Classical nucleation theory dictates that to reduce the heterogeneous nucleation of scale, the surface should have low surface energy and be as smooth as possible. Past approaches have focused on lowering surface energy via the use of hydrophobic coatings and have created atomically smooth interfaces to eliminate nucleation sites, or both, via the infusion of low-surface-energy lubricants into rough superhydrophobic substrates. Although lubricant-based surfaces are promising candidates for antiscaling, lubricant drainage inhibits their utilization. Here, we develop methodologies to deposit slippery omniphobic covalently attached liquids (SOCAL) on arbitrary substrates. Similar to lubricant-based surfaces, SOCAL has ultralow roughness and surface energy, enabling low nucleation rates and eliminating the need to replenish the lubricant. To enable SOCAL coating on metals, we investigated the surface chemistry required to ensure high-quality functionalization as measured by ultralow contact angle hysteresis (<3°). Using a multilayer deposition approach, we first electrophoretically deposit (EPD) silicon dioxide (SiO 2 ) as an intermediate layer between the metallic substrate and SOCAL. The necessity of EPD SiO 2 is to smooth (<10 nm roughness) as well as to enable the proper surface chemistry for SOCAL bonding. To characterize antiscaling performance, we utilized calcium sulfate (CaSO 4 ) scale tests, showing a 20× reduction in scale deposition rate than untreated metallic substrates. Descaling tests revealed that SOCAL dramatically decreases scale adhesion, resulting in rapid removal of scale buildup. Furthermore, our work not only demonstrates a robust methodology for depositing antiscaling SOCAL coatings on metals but also develops design guidelines for the creation of antifouling coatings for alternate applications such as biofouling and high-temperature coking.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Joining Techniques for Novel Metal Polymer Hybrid Heat Exchangers

In the United States, over 50% of the unrecovered energy from industrial processes is in the form of low-grade heat (< 220°C). Materials and maintenance costs of common heat exchangers are typically too high to justify their usage. Polymers, though more affordable, are usually unsuitable for HX applications due to their low thermal conductivity (~0.2 W/mK). Here, we show that metal-polymer hybrids may be attractive from both performance and cost perspectives. The use of polymers further increases the resistance to corrosion by sulfuric and carbonic acids often present in flue gases. An ongoing work explores different configurations of layered polyimide-copper macroscale hybrids for heat exchanger applications using numerical simulations. This paper explores a manufacturing pathway for producing such layered hybrid tubes that involves directly rolling and bonding tapes made of polymer and copper foil into tubes. A critical problem in the fabrication process is the bonding of metal and polymers. We explore approaches involving adhesives (epoxy, acrylic and silicone) for metal/polymer interfaces and direct welding (ultrasonic) for metal/metal interfaces that can be integrated into the manufacturing process. We report characterizations of the thermomechanical properties of these joining processes. This work paves the way for realizing cost-effective manufacturing of heat exchangers for low grade waste heat recovery.

Kuntumalla, Gowtham↗

Ultrasonic Welding of Soft Polymer and Metal: A Preliminary Study

Joining soft polymers and metals is receiving increasing attention in both industry and academia to enable the manufacturing of innovative products. One motivation arises from the production of next-generation heat exchanges, the structure of which is primarily composed of polymers and metals. Waste heat coming from low temperature exhaust gas stream is significant in industries in the U.S. However, traditional heat exchangers that are available to recover heat in the presence of small temperature difference are large and costly, restricting the wide application of such heat exchangers. To address this challenge, a hybrid materials design is proposed to achieve a balance between thermal conductivity and mechanical strength. High quality requirement induced by the changing operating conditions necessitates a strong bonding between polymers and copper. In this research, the possibility of using ultrasonic welding, which is conventionally employed to join dissimilar or similar metal layers, is explored. Preliminary results from welding experiments and tensile shear tests reveal that two bonding modes exist in the welding of PET and copper. Furthermore, analysis of power signals collected during welding shows that one can potentially monitor and optimize welding processes using monitoring signals. It is concluded from this study that ultrasonic welding has excellent potential in joining soft polymers and metals. Future work is also discussed on the process improvement and mechanism investigation.

Meng, Yuquan↗

JOINING TECHNIQUES FOR NOVEL METAL POLY MER HYBRID HEAT EXCHANGERS

In the United States, over 50% of the unrecovered e nergy from industrial processes is in the form of low- grade heat (<220°C). Materials and maintenance co sts of common heat exchangers are typically too hig h to justify their usage. Polymers, though more afford able, are usually unsuitable for HX applications due t o their low thermal conductivity (~0.2 W/mK). Here, we show that metal-polymer hybrids may be attractiv e from both performance and cost perspectives. The use of polymers further increases the resistance to c orrosion by sulfuric and carbonic acids often present in flue gases. An ongoing work explores different co nfigurations of layered polyimide-copper macroscale hybrids for heat exchanger applications using numeri cal simulations. This paper explores a manufacturing pathway for producing such layered hybrid tubes tha t involves directly rolling and bonding tapes made of polymer and copper foil into tubes. A critical problem in the fabrication process is the bonding of metal and polymers. We explore approaches involving adhesiv es (epoxy, acrylic and silicone) for metal/polymer inte rfaces and direct welding (ultrasonic) for metal/metal interfaces that can be integrated into the manufacturi ng process. We report characterizations of the therm omechanical properties of these joining processes. T his work paves the way for realizing cost-effective m anufacturing of heat exchangers for low grade waste heat recovery.

Kuntumalla, Gowtham↗

Materials-to-device design of hybrid metal-polymer heat exchanger tubes for low temperature waste heat recovery

Heat exchangers for low temperature (<150 °C) waste heat recovery (WHR) are challenging due to severe constraints on materials costs, manufacturing methods, and maintenance opportunities after installation. Here, the use of polymers instead of metals, offers an avenue for cost reduction in WHR applications, provided the typical low thermal conductivity of polymers (~0.2 W m –1 K –1 ) that results in poor overall heat transfer coefficient can be overcome. Previous approaches to enhance the thermal conductivity of polymers remain problematic in terms of cost, thermal, and thermomechanical considerations. In this work, we propose a novel hybrid metal-polymer composite assembled from strips of polymer and copper. Polymer strips with metal-clad edges are wound helically and the interfaces between the strips joined to obtain a tube for a cross-flow heat exchanger. Interfaces are designed to enhance effective heat conduction across the material and increase the overall heat transfer coefficient. Through numerical simulations, we obtain metal-polymer layouts that achieve wall effective thermal conductivity ~1 W m –1 K –1 at ~23% or ~35% volume fraction of copper or aluminum, respectively. The conductivity enhancement is sufficient for typical low temperature WHR, resulting in a ~20% enhancement in the overall heat transfer coefficient compared to a similar all-polymer heat exchanger. Thermomechanical simulations revealed that the composite pipe designs can withstand >1.4 MPa internal pressure, under the normal operating conditions of the heat exchanger. Our work provides guidelines for designing macroscopic metal-polymer composites that can be adapted for specific requirements such as reduced materials costs, ease of manufacturing, and heat transfer enhancement. In conclusion, the optimized design of hybrid metal-polymer heat exchanger tubes potentially provides a scalable and cost-effective route toward harvesting waste heat from low temperature sources.

42 ENGINEERING↗

Anti-scalingproperties of SOCAL coating on aluminumsubstrate

n this work, we proposed an innovative coating on Aluminumwith exceptional anti-scalingperformance. The coating features a sandwich structure with electrophoresis deposited (EPD) SiO2as intermediate layer between aluminumsubstrate and SOCALomniphobic coating. This EPD SiO2coating shows unprecedented smoothnesswhich, combined with low surface energy SOCAL coating, translated toanti scaling property. To characterize scaling, we utilized CaSO4and CaCO3scale tests, showing up to 20X less scaling than uncoated aluminum. Descaling tests revealed that our SOCAL coatings dramatically decrease scale adhesion, resulting in rapid removal of scale buildup in highly supersaturated conditions.

Zhao, Hanyang↗

Slippery Omniphobic Covalently Attached Liquids for Extreme Anti-Scaling

Fouling is amajor unresolved problem in a varietyof industries including power generation, water desalination,and hydrometallurgy. In a heat exchanger, the accumulated salt scale could lead to a decrease in heat transfer, corrosion, blockage of flow and increasedpressure drop, resulting in higher operation costsand shortened equipment lifetime. The added operational costs due to active scale removal techniques such as mechanical abrasion and chemical inhibitors are responsible for 0.25% of the GDP in industrialized nations.Herewe utilize slippery omniphobic covalently attached liquids (SOCAL) dip coating on aluminum substrates to minimize surface energyand surface roughness, hence maximizingthe energy barrier for scale formation. To enable SOCAL surfacebinding on aluminum, we started by depositinga nanoscale(500 nm thick)adhesion layer of SiO2using scalable and cost-effective electrophoretic deposition (EPD), followed by SOCAL grafting to the SiO2.The EPD SiO2coating chemistry was tailored to achieve a smoothsurface finish which, combined with the low surface energyof the SOCAL coating, translated to extreme anti-scaling performance. Thermal degradation testing in an ambient environment revealed the covalently bonded SOCAL coatingswithstand temperatures of 100°C. To characterize scaling, we utilized CaSO4and CaCO3scale tests, showing up to 20X less scaling than uncoated aluminum. Descaling tests revealed that our SOCAL coatings dramatically decrease scale adhesion, resulting in rapid removal of scale buildup in highly supersaturated conditions. To investigate manufacturability, two alternate methods of SiO2deposition were tested, including physical vapor deposition and spin-on glass, with great success in coating smooth metallic substrates, but limited success due to the inability to coat arbitrarily shaped surfaces. Our work not only demonstrates a facile method of tailoring interfacial energy and roughness to control fouling, it develops cost-effective, scalable,and high performing anti-fouling coating applicable to aluminum surfacesfor a variety of applications.

Zhao, Hanyang↗

Composite Structured Surfaces for Durable Dropwise Condensation

Condensation heat transfer is a vital process for a plethora of industrial application. Dropwise condensation of steam on hydrophobic polymers, typified by the formation of discrete water droplets which shed and clear the surface for re-nucleation, has a 10X higher heat transfer coefficient when compared to filmwise condensation on bare metallic surfaces. However, 8 decades of research have conclusively demonstrated a lack of durability of the hydrophobic coatings during dropwise condensation to quantify industrial implementation. They key bottleneck is the coating conundrum, which states that thick hydrophobic coatings (> 10 µm) are required for higher durability, while thin hydrophobic coatings (< 1 µm) are required for low parasitic thermal resistance due to the low intrinsic thermal conductivity of polymeric materials (k ~ 0.1 W/m·K). Here, we attempt to solve the conundrum by developing rationally-designed metal-polymer composite coatings to increase the effective thermal conductivity of the hydrophobic coating, thereby enabling thicker coatings for higher durability. We study nanowire, inverse opal, and sintered sphere metallic structures infilled with hydrophobic polymers. To quantify the heat transfer performance, we analyze the vapor-to-coolant and vapor-to-surface heat transfer coefficients of composite coated flat surfaces having varying wire/sphere diameters (D = 100 nm, 1 μm, 10 μm) and coating thickness (10 nm < t < 100 μm) using three-dimensional (3D), steady state, Comsol simulations. We show that analytical models such as Maxwell or effective medium theory fail to predict the composite thermal conductivity. By conducting simulation with two independent sets of boundary conditions; isothermal surfaces and convection, as well as by varying the interfacial metal fractions, we demonstrate the importance of 3D heat spreading near the coating-vapor and coating-substrate interface. To predict the wetting characteristics to ensure stable dropwise condensation, we coupled our 3D heat transfer simulations to a unified model for contact angle hysteresis on heterogeneous surfaces. Our wetting predictions identify the key tradeoff between low spreading resistance (high k, filmwise condensation) and low contact angle hysteresis (low k, dropwise condensation) on high and low surface metal fractions, respectively, and identify the optimum metallic structure, volume fraction, interfacial solid fraction, and thickness for enhanced durability. Our work provides a novel approach to utilize rational metallic nanostructuring to create composite hydrophobic coatings which promise enhanced durability.

Chang, Ho Chan↗

Thermomechanical design optimization for low metal footprint in hybrid metal-polymer heat exchanger

Material and maintenance costs of metal-based heat exchangers surpass profits in waste heat recovery (WHR) from ultra-low temperature (<100C) sources [1]. A low-cost alternative like polymer pipes suffer from poor thermal conductivity (~0.2 W/mK), and a low overall heat transfer coefficient. Polymers’ thermal conductivity have previously been enhanced through systematic molecular alignment by stretching [2], chemical vapor deposition of extended polymers [3], surface grating [4], etc. However, these approaches suffer from scalability issues for WHR heat exchangers in terms of cost [3], and thermomechanical considerations [5]. In this work, we propose novel hybrid metal-polymer heat exchangers that are made from polymer-copper strips. Through finite element method (FEM) simulations, we first optimize the placement of copper around polymer strips to enhance the transverse thermal conductivity of the strips. The copper cladded polymer strips are wound helically in a roll-to-roll system to form the pipes for a heat exchanger. We then optimize the design of helically wound pipes to reduce thermomechanical strains to < 0.2 % at 100C and 40 psi working conditions. At 25 % volume fraction of copper in the pipe, we predict up to 20 % enhancement in overall heat transfer from a base polymer with a thermal conductivity of 0.2 W/mK. We also compare and contrast the thermomechanical performance of the optimized metal-polymer strips to random metal matrix composites. Finally, we experimentally verify the thermal conductivity of the optimized strips through bulk thermal conductivity and thermal interface resistance measurement setup. By systematically improving the design through FEM and experimental measurements, we provide an optimized design of hybrid metal-polymer pipes that provides a low metal footprint and cost-effective means for harvesting waste heat from ultra-low temperature sources. Thekdi, Arvind, and Sachin U. Nimbalkar. Oak Ridge National Lab, 2015 Shen, Sheng, et al. Nature nanotechnology 5.4 (2010): 251. Xu, Yanfei, et al. Science advances 4.3 (2018): 3031. Smith, M. K., Singh, V., Kalaitzidou, K., & Cola, B. A. (2015). ACS nano, 9(2), 1080-1088. Aymonier, C., Bortzmeyer, D., Thomann, R., & M&uuml;lhaupt, R. (2003). Chemistry of Materials, 15(25), 4874-4878.

C Rajagopal, Manjunath↗