Engineering topics

Chaudhary, Sumit

Publications and source records attributed to Chaudhary, Sumit.

8 records

DOE OSTI2016

Tailoring nanoscale morphology of polymer: Fullerene blends using electrostatic field

In this paper, to tailor the nanoscale phase separation in polymer/fullerene blends, we study the effect of electrostatic field (E-field) on the solidification of poly(3-hexylthiophene-2, 5-diyl) (P3HT):[6,6]-phenyl-C61-butyric acid methyl ester (PC 60 BM) bulk heterojunction (BHJ). In addition to untreated sample (control); wet P3HT:PC 60 BM thin films were exposed to E-field of Van de Graaff (VDG) generator at three different directions – horizontal (H), tilted (T) and vertical (V) – relative to the plane of the substrate. Surface and bulk characterizations of field-treated BHJs affirm that fullerene molecules can easily penetrate the spaghetti-like P3HT and move up and down following the E-field. E-field treatment yields thin films with large P3HT- and PCBM-rich domains acting as continuous pathways for efficient charge separation, transport, and collection. We improve; (1) the hole mobility values up to 19.4 × 10 -4 ± 1.6 × 10 -4 cm 2 V -1 s -1 (117% higher than the control), and (2) power conversion efficient (PCE) of conventional and inverted OPVs recording 2.58 ± 0.02% and 4.1 ± 0.4%. This E-field approach can serve as a new morphology-tuning technique, which is generally applicable to other polymer-fullerene systems.

36 MATERIALS SCIENCE↗

DOE OSTI2016

Textured micrometer scale templates as light managing fabrication platform for organic solar cells

A three-dimensional, microscale-textured, grating-shaped organic solar cell geometry. The solar cells are fabricated on gratings to give them a three-dimensional texture that provides enhanced light absorption. Introduction of microscale texturing has a positive effect on the overall power conversion efficiency of the devices. This grating-based solar cell having a grating of pre-determined pitch and height has shown improved power-conversion efficiency over a conventional flat solar cell. The improvement in efficiency is accomplished by homogeneous coverage of the grating with uniform thickness of the active layer, which is attributed to a sufficiently high pitch and low height of the underlying gratings. Also the microscale texturing leads to suppressed reflection of incident light due to the efficient coupling of the incident light into modes that are guided in the active layer.

14 SOLAR ENERGY↗

DOE OSTI2016

Characterizing Electric Field Exposed P3HT Thin Films Using Polarized-Light Spectroscopies

P3HT (poly (3-hexylthiophene)) has been widely used as a donor in the active layer in organic photovoltaic devices. Although moderately high-power conversion efficiencies have been achieved with P3HT-based devices, structural details, such as the orientation of polymer units and the extent of H- and J-aggregation are not yet fully understood; and different measures have been taken to control the ordering in the material. One such measure, which we have exploited, is to apply an electric field from a Van de Graaff generator. We used fluorescence (to measure anisotropy instead of polarization, which is more commonly measured) and Raman spectroscopy to characterize the order of P3HT molecules in thin films resulting from the field. We determine preferential orientations of the units in a thin film, consistent with observed hole mobility in thin-film-transistors, and observe that the apparent H-coupling strength changes when the films are exposed to oriented electrical fields during drying.

36 MATERIALS SCIENCE↗

DOE OSTI2015

Understanding defect distributions in polythiophenes via comparison of regioregular and regiorandom species

Organic photovoltaics (OPVs) are regarded as promising for solar-electric conversion with steadily improving power conversion efficiencies. For further progress, it is crucial to understand and mitigate defect states (traps) residing in the band-gap of OPV materials. In this work, using capacitance measurements, we analyzed two major bands in the density of states (DOS) energy spectra of defects in poly(3-hexylthiophene) (P3HT); regio-regular and regio-random species of P3HT were compared to elucidate the role of morphological disorder. To accurately interpret the obtained DOS profile, trap emission prefactors and activation energy were extracted from temperature dependent capacitance-frequency measurements, while doping, Fermi energy, built-in voltage, and energy levels of the defects were extracted from capacitance-voltage measurements. We identified that the lower energy band—misinterpreted in literature as a defect distribution—stems from free carrier response. The higher energy defect distribution band for regio-random P3HT was an order of magnitude higher than region-regular P3HT, thus stemming from morphological disorder. Impedance spectroscopy was also employed for further comparison of the two P3HT species.

14 SOLAR ENERGY↗

DOE OSTI2015

Synthesis and photovoltaic properties of 2,6-bis(2-thienyl) benzobisazole and 4,8-bis(thienyl)-benzo[1,2- B :4,5- B' ]dithiophene copolymers

In an effort to design efficient low-cost polymers for use in organic photovoltaic cells the easily prepared donor–acceptor–donor triad of a either cis-benzobisoxazole, trans-benzobisoxazole or trans-benzobisthiazole flanked by two thiophene rings was combined with the electron-rich 4,8-bis(5-(2-ethylhexyl)-thien-2-yl)-benzo[1,2-b:4,5-b']dithiophene. The electrochemical, optical, morphological, charge transport, and photovoltaic properties of the resulting terpolymers were investigated. Although the polymers differed in the arrangement and/or nature of the chalcogens, they all had similar highest occupied molecular orbital energy levels (-5.2 to -5.3 eV) and optical band gaps (2.1–2.2 eV). However, the lowest unoccupied molecular orbital energy levels ranged from -3.1 to -3.5 eV. When the polymers were used as electron donors in bulk heterojunction photovoltaic devices with PC71BM ([6,6]-phenyl C71-butyric acid methyl ester) as the acceptor, the trans-benzobisoxazole polymer had the best performance with a power conversion efficiency of 2.8%.

36 MATERIALS SCIENCE↗

DOE OSTI2015

Synthesis, characterization, and photovoltaic properties of dithienylbenzobisazole‐dithienylsilole copolymers

ABSTRACT Three conjugated polymers comprised of dioctyl‐dithieno‐[2,3‐ b :2',3'‐ d ]silole and a donor‐acceptor‐donor triad of either cis‐ benzbisoxazole, trans ‐benzobisoxazole or trans ‐benzobisthiazole were synthesized via the Stille cross‐coupling reaction. The impact of varying the heteroatoms and/or the location within the benzobisazole moiety on the optical and electronic properties of the resulting polymers was evaluated via cyclic voltammetry and UV‐Visible spectroscopy. All of the polymers have similar optical band‐gaps of ∼1.9 eV and highest occupied molecular orbital levels of − 5.2 eV. However, the lowest unoccupied molecular orbitals (LUMO) ranged from − 3.0 to − 3.2 eV. Interestingly, when the polymers were used as donor materials in bulk‐heterojunction photovoltaic cells with PC 71 BM as the electron‐acceptor, the benzobisoxazole‐based polymers gave slightly better results than the benzobisthiazole‐containing polymers with power conversion efficiencies up to 3.5%. These results indicate that benzobisoxazoles are promising materials for use in OPVs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53 , 1533–1540

Bhuwalka, Achala↗

DOE OSTI2014

Fourier Transform-Plasmon Waveguide Spectroscopy: A Nondestructive Multifrequency Method for Simultaneously Determining Polymer Thickness and Apparent Index of Refraction

Fourier transform (FT)-plasmon waveguide resonance (PWR) spectroscopy measures light reflectivity at a waveguide interface as the incident frequency and angle are scanned. Under conditions of total internal reflection, the reflected light intensity is attenuated when the incident frequency and angle satisfy conditions for exciting surface plasmon modes in the metal as well as guided modes within the waveguide. Expanding upon the concept of two-frequency surface plasmon resonance developed by Peterlinz and Georgiadis [ Opt. Commun. 1996, 130, 260], the apparent index of refraction and the thickness of a waveguide can be measured precisely and simultaneously by FT-PWR with an average percent relative error of 0.4%. Measuring reflectivity for a range of frequencies extends the analysis to a wide variety of sample compositions and thicknesses since frequencies with the maximum attenuation can be selected to optimize the analysis. Additionally, the ability to measure reflectivity curves with both p- and s-polarized light provides anisotropic indices of refraction. FT-PWR is demonstrated using polystyrene waveguides of varying thickness, and the validity of FT-PWR measurements are verified by comparing the results to data from profilometry and atomic force microscopy (AFM).

36 MATERIALS SCIENCE↗

DOE OSTI2014

Quantitative comparison of organic photovoltaic bulk heterojunction photostability under laser illumination

The photostability of bulk heterojunction organic photovoltaic films containing a polymer donor and a fullerene-derivative acceptor was examined using resonance Raman spectroscopy and controlled laser power densities. The polymer donors were poly(3-hexylthiophene-2,5-diyl) (P3HT), poly[[9-(1-octylnonyl)-9H-carbazole-2,7-diyl]-2,5-thiophenediyl-2,1,3-benzothiadiazole-4,7-diyl-2,5-thiophenediyl] (PCDTBT), or poly({4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b']dithiophene-2,6-diyl}{3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl}) (PTB7). Four sample preparation methods were studied: (i) thin or (ii) thick films with fast solvent evaporation under nitrogen, (iii) thick films with slow solvent evaporation under nitrogen, and (iv) thin films dried under nitrogen followed by thermal annealing. Polymer order was assessed by monitoring a Raman peak’s full width at half-maximum and location as a function of illumination time and laser power densities from 2.5 × 10 3 to 2.5 × 10 5 W cm –2 . Resonance Raman spectroscopy measurements show that before prolonged illumination, PCDTBT and PTB7 have the same initial order for all preparation conditions, while P3HT order improves with slow solvent drying or thermal annealing. All films exhibited changes to bulk heterojunction structure with 2.5 × 10 5 Wcm –2 laser illumination as measured by resonance Raman spectroscopy, and atomic force microscopy images show evidence of sample heating that affects the polymer over an area greater than the illumination profile. Furthermore, photostability data are important for proper characterization by techniques involving illumination and the development of devices suitable for real-world applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗