Engineering topics

Chellam, Shankararaman

Publications and source records attributed to Chellam, Shankararaman.

7 records

DOE OSTI2025

AERO-MAP: a data compilation and modeling approach to understand spatial variability in fine- and coarse-mode aerosol composition

Abstract. Aerosol particles are an important part of the Earth climate system, and their concentrations are spatially and temporally heterogeneous, as well as being variable in size and composition. Particles can interact with incoming solar radiation and outgoing longwave radiation, change cloud properties, affect photochemistry, impact surface air quality, change the albedo of snow and ice, and modulate carbon dioxide uptake by the land and ocean. High particulate matter concentrations at the surface represent an important public health hazard. There are substantial data sets describing aerosol particles in the literature or in public health databases, but they have not been compiled for easy use by the climate and air quality modeling community. Here, we present a new compilation of PM2.5 and PM10 surface observations, including measurements of aerosol composition, focusing on the spatial variability across different observational stations. Climate modelers are constantly looking for multiple independent lines of evidence to verify their models, and in situ surface concentration measurements, taken at the level of human settlement, present a valuable source of information about aerosols and their human impacts complementarily to the column averages or integrals often retrieved from satellites. We demonstrate a method for comparing the data sets to outputs from global climate models that are the basis for projections of future climate and large-scale aerosol transport patterns that influence local air quality. Annual trends and seasonal cycles are discussed briefly and are included in the compilation. Overall, most of the planet or even the land fraction does not have sufficient observations of surface concentrations – and, especially, particle composition – to characterize and understand the current distribution of particles. Climate models without ammonium nitrate aerosols omit ∼ 10 % of the globally averaged surface concentration of aerosol particles in both PM2.5 and PM10 size fractions, with up to 50 % of the surface concentrations not being included in some regions. In these regions, climate model aerosol forcing projections are likely to be incorrect as they do not include important trends in short-lived climate forcers.

Mahowald, Natalie M. (ORCID:000000022873997X)↗

DOE OSTI2024

Porous Iron Electrodes Reduce Energy Consumption During Electrocoagulation of a Virus Surrogate: Insights into Performance Enhancements Using Three-Dimensional Neutron Computed Tomography

Electrocoagulation has attracted significant attention as an alternative to conventional chemical coagulation because it is capable of removing a wide range of contaminants and has several potential advantages. In contrast to most electrocoagulation research that has been performed with nonporous electrodes, in this study, we demonstrate energy-efficient iron electrocoagulation using porous electrodes. In batch operation, investigation of the external pore structures through optical microscopy suggested that a low porosity electrode with sparse connection between pores may lead to mechanical failure of the pore network during electrolysis, whereas a high porosity electrode is vulnerable to pore clogging. Electrodes with intermediate porosity, instead, only suffered a moderate surface deposition, leading to electrical energy savings of 21% and 36% in terms of electrocoagulant delivery and unit log virus reduction, respectively. Neutron computed tomography revealed the critical role of electrode porosity in utilizing the electrode’s internal surface for electrodissolution and effective delivery of electrocoagulant to the bulk. Energy savings of up to 88% in short-term operation were obtained with porous electrodes in a continuous flow-through system. Further investigation on the impact of current density and porosity in long-term operation is desired as well as the capital cost of porous electrodes.

42 ENGINEERING↗

DOE OSTI2024

Constraining Present‐Day Anthropogenic Total Iron Emissions Using Model and Observations

Abstract Iron emissions from human activities, such as oil combustion and smelting, affect the Earth's climate and marine ecosystems. These emissions are difficult to quantify accurately due to a lack of observations, particularly in remote ocean regions. In this study, we used long‐term, near‐source observations in areas with a dominance of anthropogenic iron emissions in various parts of the world to better estimate the total amount of anthropogenic iron emissions. We also used a statistical source apportionment method to identify the anthropogenic components and their sub‐sources from bulk aerosol observations in the United States. We find that the estimates of anthropogenic iron emissions are within a factor of 3 in most regions compared to previous inventory estimates. Under‐ or overestimation varied by region and depended on the number of sites, interannual variability, and the statistical filter choice. Smelting‐related iron emissions are overestimated by a factor of 1.5 in East Asia compared to previous estimates. More long‐term iron observations and the consideration of the influence of dust and wildfires could help reduce the uncertainty in anthropogenic iron emissions estimates.

Meteorology & Atmospheric Sciences↗

DOE OSTI2024

Performance Restoration of Iron Electrodes by Polarity Reversal after Long-Term Surface Fouling in Wastewater Electrocoagulation

Iron electrocoagulation (Fe-EC) performance often declines with time, producing lower contaminant removal efficiencies and higher energy requirements due to formation of a fouling layer on the electrodes. Here, we investigate the formation of the fouling layer and the effectiveness of polarity reversal to restore the Fe-EC performance. A thin, porous iron oxide layer initially forms on the anode, thickening into a dense, over 150-μm thick crystalline layer after extended operation. This fouling layer restricts dissolution and diffusion of Fe ions into the bulk solution, thus increasing the anode potential required to maintain a desired electrical current and decreasing Faradaic efficiency. Polarity reversal applied when performance decline is observed effectively removes the fouling layer, thereby restoring Faradaic and contaminant removal efficiencies and decreasing energy consumption. Our findings suggest that gas generation at the cathode surface after polarity reversal causes removal of the fouling layer. This study enhances the current understanding of fouling-layer formation in Fe-EC and offers a practical approach, involving polarity reversal, to maintain electrode reactivity and optimal Fe-EC performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Electrocoagulation of high-salinity produced water: lessons learned from its early applications in unconventional reservoir plays

Ample research has demonstrated that electrocoagulation is a versatile technology capable of facilitating the removal of a wide range of physical, biological, organic, and inorganic constituents such as suspended solids, turbidity, bacteria, viruses, oil and grease, organic carbon (including chemical and biological oxygen demand), silica, fluoride, and so on. Despite its purported advantages and extensive lab-scale evaluations, it has not yet been widely adopted for water and wastewater treatment and reuse at commercial scale. This is symptomatic of a chasm between its technological capabilities on one hand and field performance and reputation on the other. Herein, we opine as to why this might be the case using our collective experiences with the oil and gas industry as an exemplar. In this study, we highlight scientific, technological, engineering, and business issues that need to be addressed to realize the full potential of this promising technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Mine Water Use, Treatment, and Reuse in the United States: A Look at Current Industry Practices and Select Case Studies

Mining provides significant economic value while often impacting local water supplies and environments because of freshwater usage and waste disposal practices. In this paper we identify current practices in mine water, including how water is used in mining, influent and effluent water quality, treatment technologies, and end uses with the goal of informing future research on implementable, reliable, and cost-effective advanced water treatment in the mining sector. This study also reviews the available literature to broadly evaluate mining in the United States and performs a techno-economic assessment on water use and disposal for three detailed case studies applicable to lithium, uranium, and copper mines. These case studies highlight specific industry examples of distinct extraction methods, geographical regions, and mined commodities. Hypothetical scenarios based on case study baselines revealed potential impacts to mine water available for beneficial reuse through the use of novel water treatment technologies and alternate water management strategies. Finally, an assessment of national level impacts resulting from the reuse of treated mine source water is presented.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2021

Anthropogenic Perturbations to the Atmospheric Molybdenum Cycle

Abstract Molybdenum (Mo) is a key cofactor in enzymes used for nitrogen (N) fixation and nitrate reduction, and the low availability of Mo can constrain N inputs, affecting ecosystem productivity. Natural atmospheric Mo aerosolization and deposition from sources such as desert dust, sea‐salt spray, and volcanoes can affect ecosystem function across long timescales, but anthropogenic activities such as combustion, motor vehicles, and agricultural dust have accelerated the natural Mo cycle. Here we combined a synthesis of global atmospheric concentration observations and modeling to identify and estimate anthropogenic sources of atmospheric Mo. To project the impact of atmospheric Mo on terrestrial ecosystems, we synthesized soil Mo data and estimated the global distribution of soil Mo using two approaches to calculate turnover times. We estimated global emissions of atmospheric Mo in aerosols (<10 μm in diameter) to be 23 Gg Mo yr −1 , with 40%–75% from anthropogenic sources. We approximated that for the top meter of soil, Mo turnover times range between 1,000 and 1,000,000 years. In some industrialized regions, anthropogenic inputs have enhanced Mo deposition 100‐fold, lowering the soil Mo turnover time considerably. Our synthesis of global observational data, modeling, and a mass balance comparison with riverine Mo exports suggest that anthropogenic activity has greatly accelerated the Mo cycle, with potential to influence N‐limited ecosystems.

Wong, Michelle Y.↗