Search NASA⌕ Search

Engineering topics

Chen, Ching-Fong

Publications and source records attributed to Chen, Ching-Fong.

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Pseudo-Hot-Isostatic Pressing (P-HIP)

Researchers at Los Alamos National Laboratory developed a technology to produce high performance ceramic or metal with a combination of major key properties such as versatile-complicated shape, high density, uniform density distribution, and minimal amounts of starting material. The novel pseudo-hot-isostatic-pressing (P-HIP) uses graphite or boron nitride flakes as the stress transmission media to transmit stress instead of the conventional solid graphite punch. The graphite and boron nitride flakes are solid lubricants and can slide among one another to re-distribute the stress from high stress concentration area to the low stress concentration areas, resulting in a self-stress-relief action. This innovative P-HIP enables the manufacturing of complicated shapes with near-net-shape capability while minimizing the energy used and reducing waste. This is a revolutionary breakthrough to the ceramics and powder metallurgy industries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal Processing Conditions for the Synthesis of Near Theoretical Density Li 5 La 3 Ta 2 O 12 Ceramics for Ceramic Dual-Mode Detectors

A family of Li-containing garnet compounds, extensively investigated for Li-ion solid electrolyte applications, show great potential to be developed into transparent ceramic dual-mode scintillators. In particular, Li 5 La 3 Ta 2 O 12 (LLTaO) shows promise as an efficient dual-mode scintillator due to its high Li content, high density, non-hygroscopicity, and high effective-Z. Often the synthesis of LLTaO ceramics involves solid state processing techniques starting with oxide and carbonate powders, calcining, sintering for the removal of residual porosity, and post-processing. This study focuses on two objectives: (1) establishing thermal processing boundary conditions for a flexible alkoxide-based sol-gel method for synthesizing fine-grained powders; and (2), consolidating powders via hot-pressing to form high-density ceramics. In this study, near single-phase ceramics were achieved by hot-pressing sol-gel powders with varying amounts of excess Li. Rietveld refinements were used to analyze X-ray diffraction data and provide a quantitative evaluation of the phases present in the hot pressed ceramics. Some of the diffraction data showed large low angle peak asymmetry, suggesting the presence of two cubic Li 5 La 3 Ta 2 O 12 garnet phases with different lattice parameters. Depending on the synthesis and processing conditions, the refinement revealed ~ 90 wt% concentration of a phase with a ≈ 12.8 Å and ~ 10 wt% concentration of a phase with a ≈ 12.9 Å, indicating a remaining excess of Li in the hot pressed ceramics in the large lattice parameter phase. These synthesis experiments allowed for the determination of a baseline for Li loss during hot-pressing. X-ray excited radioluminescence and photoluminescence excitation and emission spectra were obtained from the hot pressed ceramics. In conclusion, the measured emission spectra featured broad tantalate emission and line emissions likely from a rare-earth impurity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Simulations of Sweeping Wave Propagation in a Boron Carbide Plate

In February 2020, experiments were conducted at Los Alamos National Laboratory measuring the propagation of a sweeping wave through a plate of boron carbide which was induced by detonating an adjacent charge of high explosive. Six such shots were red and in each case progress of the wave along the exposed surface of the plate was tracked using photon doppler velocimetry (PDV). In this report we discuss calculations performed using the Lagrangian hydrocode FLAG to model data taken from these experiments. We discuss the models chosen for the different experimental components, the choice of mesh (focusing on, both, two- and three-dimensional geometries), and compare the results from these calculations to experimentally-extracted PDV traces. Notably, we find that the PDV traces for this experiment are most faithfully reproduced using the full three-dimensional geometry, even when the mesh resolution for the three-dimensional calculations was significantly lower than the resolution for the corresponding two-dimensional calculations. We attribute this to the geometry of the experimental setup. Moreover, we find only negligible differences for the PDV traces obtained using the sesame table equation of state for boron carbide and the Gruneisen equation of state.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tape casting and characterizations of MgO ceramics

Herein we report a high density MgO ceramic substrate produced by the tape casting technology. The tape casting formulation and process produced a uniform tape free of cracking. Y 2 O 3 and SiO 2 were used as the sintering aid for the pressureless sintering of the green tape. X-ray diffraction phase identification indicates that MgO is the main phase, while both Y 2 O 3 and SiO 2 sintering aids react with MgO to form MgY 4 Si 3 O 13 as the second phase. Liquid phase sintering occurs in the temperature range from 1030°C to ~1500°C, which is confirmed by the simultaneous Thermal Gravitation Analysis/ Differential Scanning Calorimeter (TGA/DSC) and the percent linear shrinkage and densification. A 96.5% theoretical density was achieved by presureless sintering at 1650°C for 2 hours, which was further increased to a fully dense structure using hotisostatic- pressing(HIP) at 1650°C and 207 MPa in argon. Scanning electron microscopy (SEM) and energy dispersive(EDS) spectroscopic analysis on the HIP’ed sample show that MgY 4 Si 3 O 13 is located at the MgO grain boundary and the sample has a fully dense structure. The refractive indices and extinction coefficient were measured on the HIP’ed sample along with thermal properties and dielectric properties. Thermal diffusivity and heat capacity were measured to calculate the thermal conductivity.

36 MATERIALS SCIENCE↗