Certified data-driven physics-informed greedy auto-encoder simulator
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Chen, J S.
Explore the source record for details and available documents.
FePt-SiN{sub x}-C films on TiN/CrRu/glass substrate with large coercivity, (001) texture, and small isolated grains were obtained by co-sputtering FePt, Si{sub 3}N{sub 4}, and C targets at 380 deg. C. It was found that when C was doped into the FePt-SiN{sub x} films, the out-of-plane coercivity increased while the small in-plane coercivity remained unchanged. Grain size decreased and grain size distribution became more uniform with increasing the C doping concentration. The x-ray photoelectron spectroscopy (XPS) depth profile showed a uniform depth distribution of Si in the FePt layer. The Si2p XPS spectrum implied the existence of Fe-Si bonds, indicating that SiN{sub x} was located at the FePt grain boundaries and was stable against diffusion to the surface, thus favoring grain isolation. Well-isolated FePt (001) granular films with coercivity higher than 21.5 kOe and an average grain size of 5.6 nm were obtained by doping 40 vol. % of SiN{sub x} and 20 vol. % of C.
TiN was investigated as a potential spacer material in L1{sub 0}-FePt based pseudo spin valves (PSV). PSVs with the structure MgO/L1{sub 0}-Fe{sub 50}Pt{sub 50} (20 nm)/TiN (5 nm)/L1{sub 0}-Fe{sub 50}Pt{sub 50} (x nm) were fabricated, where x was varied from 5 to 20 nm. The highest giant magnetoresistance (GMR) ratio of 0.61% was obtained for the PSV with a top L1{sub 0}-FePt thickness of 20 nm. Contributions to the GMR arose from both the spin dependent scattering at the FePt/TiN interfaces and domain wall resistivity. Magnon magnetoresistance was also observed in the fabricated PSVs.
The effect of the CrRu-SiO{sub x} underlayer with different doping concentrations and the thickness of the CrRu underlayer on the microstructure and magnetic properties of FePt-C films were investigated. FePt films exhibited L1{sub 0} (001) texture at various SiO{sub x} doping concentrations. The coercivities were as large as 28 kOe and the slope of M-H loop at coercivity was approximately equal to 1, suggesting that FePt grains were well exchange decoupled. Grain size was only slightly reduced after introducing the CrRu-SiO{sub x} underlayer. But the contact angle between the FePt grains and the MgO intermediate layer around 135 deg. indicated the a MgO intermediate layer was not favored for smaller grains to obtain good L1{sub 0} (001) texture. X-ray photoelectron spectroscopy in-depth profile showed that Si diffused into a whole FePt-C layer and C diffused to the film surface.
Multilayer exchange spring media were fabricated by subsequently reducing the deposition temperature of the FePt-C film from the bottom layer to the top layer. Magnetic anisotropy and coercivity of FePt-C film increased with the increasing of deposition temperature because the chemical ordering of L1{sub 0} FePt improved with deposition temperature. A two-layer microstructure was observed in the multilayer samples with a closely-packed granular hard layer and an isolated granular overlayer consisting of the soft magnetic layers deposited at lower temperatures. The coercivity of the tri-layer media was reduced to 5.4 kOe, half of that of the hard single layer FePt-C (10.8 kOe). The thermal stability of the multilayer structure was maintained although some soft magnetic layers involved.
Crystallographic structure, growth induced miscibility gap and strain in Ta/Co{sub 100-x}Pt{sub x} (0 {le} x {le} 43 at%)/Ru/Ta/glass films deposited at ambient temperature were investigated using polarized x-ray absorption spectroscopy to clarify the origin of observed perpendicular magnetic anisotropy (PMA) in Co{sub 72}Pt{sub 28} film. Extended x-ray absorption fine structure spectroscopy data at Co K-edge showed that Co has a similar local atomic environment and averaged interatomic distance in the in-plane and out-of-plane polarization geometries for Co{sub 72}Pt{sub 28}, ruling out the contribution of magneto-elastic anisotropy and growth induced structural anisotropy as the origin of PMA. A large PMA in Co{sub 72}Pt{sub 28} film was attributed to the preferred hexagonal close-packed stacking as observed using the x-ray absorption near-edge structure spectroscopy.
FePt-X (X=C, TiO{sub 2}, Ta{sub 2}O{sub 5}) nanocomposite films were deposited on MgO/CrRu/glass substrates at 350 deg. C by magnetron cosputtering. The comparison investigations on the magnetic properties and microstructure of FePt-X films with various dopants were conducted. All FePt-X films showed (001) preferred orientation and oxide dopants promoted the formation of magnetically soft fcc FePt phase. With 15 vol % C doping, FePt-C film with columnar grains of 7.5 nm was obtained and the out-of-plane coercivity measured at room temperature was as high as 14.4 kOe. The increase in carbon volume fraction to 20% caused the formation of two-layer structure, whereas for the 20 vol % TiO{sub 2} and Ta{sub 2}O{sub 5} doping, the columnar structure of the FePt films remained and the corresponding grain sizes were 5 and 10 nm, respectively. Ta{sub 2}O{sub 5} doping showed better grain isolation than the others. The out-of-plane coercivities of FePt-TiO{sub 2} and FePt-Ta{sub 2}O{sub 5} films were 7.5 and 8.8 kOe, respectively.
L1{sub 0} FePt-Ta{sub 2}O{sub 5} films with (001) texture were synthesized by cosputtering FePt and Ta{sub 2}O{sub 5} targets and in situ heated at 350 deg. C. The (001) preferred orientation was preserved even when doped with 20 vol % Ta{sub 2}O{sub 5}. The out-of-plane coercivity, H{sub c}, increased from 6.7 kOe (for pure FePt film) to 8.8 kOe when doped with 20 vol % Ta{sub 2}O{sub 5}. Further increase in the dopant content to 25 and 30 vol % caused H{sub c} to decrease significantly to below 3 kOe. Well-isolated FePt grains of tall column structures were observed for the 12 nm thick FePt film when doped with 20 vol %. The loop slope parameter, {alpha}, of such FePt film approached 1.
Carbon dioxide (CO{sub 2}) adsorption isotherms were measured on five different rank coals at 328.2 K and pressures up to 13.8 MPa using a volumetric method. Specifically, Beulah Zap, Illinois no.6, Pocahontas No.3, Upper Freeport, and Wyodak coals from the Argonne premium coal sample program were used for these isotherm measurements. These newly acquired data are compared to our previous data on dry coals. As expected, the adsorption on the wet coals is lower than that on the dry coals. At 7 MPa, Pocahontas, Upper Freeport, Illinois no. 6, Wyodak, and Beulah Zap coals exhibited, respectively, about 19, 17, 48, 76, and 79% reduction in the amount adsorbed on the wet coal when compared to the adsorption on the dry coal. These reductions in CO{sub 2} adsorption correlate positively with the amount of moisture present on the coal. The isotherms on wet coals were measured at their equilibrium moisture content. The adsorption isotherm for each of the wet coals exhibited a Gibbs adsorption maximum between 8 and 12 MPa and occurred at a higher pressure than that of the dry coal. The simplified local-density/Peng-Robinson model was used to correlate the adsorption data. The model was found capable of representing precisely the CO{sub 2} adsorption on both dry and wet coals. Specifically, the overall weighed average absolute deviation (WAAD) for the five dry and wet coals was 0.99 and 0.42, respectively. Nevertheless, more rigorous accounting for the water interactions with the coal matrix and the competitive adsorption between water and CO{sub 2} would provide an even more realistic description of coal-bed gas adsorption phenomenon on wet coals. 43 refs., 10 figs., 9 tabs.
The seedlayer effect on crystallographic structure and magnetic properties of cosputtered SmCo films on Cu underlayer was investigated. Highly textured (001) SmCo{sub 5} thin films were obtained by introducing a thin Ti or Ta seedlayer. Especially, with the Ta seedlayer, the half maximum of the rocking curve of SmCo (001) peak was as small as 3.4 deg. and the high-index SmCo{sub 5} (003) diffraction peak was clearly observed, showing a high quality of texture and crystallinity. The SmCo{sub 5} films showed a large perpendicular anisotropy with out-of-plane coercivities over 20 kOe. Well crystallized SmCo{sub 5} films with (001) texture could be obtained at a temperature as low as 325 deg. C. The crystallinity, (001) texture, and magnetic properties of SmCo{sub 5} thin films were found to be dependent on deposition temperature, the texture of the Cu (111) underlayer, roughness of the Cu underlayer, and formation of SmCoCu alloy through the Cu diffusion.
FePt:TiO{sub 2} (001) thin films were deposited on CrRu/MgO underlayers by dc magnetron cosputtering. The effects of TiO{sub 2} content on microstructure and magnetic properties of the epitaxial FePt (001) films were studied. Experimental results showed that even with 20 vol % TiO{sub 2} doping, FePt films could keep a (001) preferred orientation and perpendicular anisotropy. The FePt:TiO{sub 2} (001) film with 5 nm grain size, adjustable coercivity, and reduced exchange coupling was obtained by doping 20 vol % TiO{sub 2} into FePt film, showing great potential as low noise ultrahigh density perpendicular magnetic recording media.
Nanodiamond (ND) is surrounded by layers of graphite on its surface. This unique structure feature creates unusual fluorescence spectra, which can be used as an indicator to monitor its surface modification. Meanwhile, the impurity, nitroso (C-N=O) inside the ND can be photolyzed by two-photon absorption, releasing NO to facilitate the formation of a sp{sup 3} diamond structure in the core of ND and transforming it into a sp{sup 2} graphite structure. Such a conformational transition enlarges the size of ND from 8 to 90 nm, resulting in a popcornlike structure. This transition reaction may be useful as nanoknives in biomedical application.
Structural and magnetic properties of SmCo{sub 5} thin films grown on glass substrates with a Cr underlayer were investigated. The nanocrystalline SmCo{sub 5} film with a (1120) texture exhibited high in-plane intrinsic coercivity up to 26.5 kOe and a large in-plane magnetic anisotropy. The crystallinity of the SmCo{sub 5} layer plays an important role, which is strongly dependent on the texture and the morphology of the Cr underlayer. A smooth Cr underlayer with a (200) texture and a good crystallinity is desired for the SmCo{sub 5} film with a good magnetic performance. This work demonstrates a process to achieve high intrinsic coercivity and large in-plane magnetic anisotropy SmCo{sub 5} films on glass substrates deposited at a relatively low temperature (400 deg. C)