Engineering topics

Chen, P. Y. P.

Publications and source records attributed to Chen, P. Y. P..

4 records

NASA NTRS2003

Investigating Morphological Stability of Faceted Interfaces with Axial Heat Processing (AHP) Technique

Successful processing of homogeneous semiconductor single crystals from their melts depends strongly on precise control of thermal and fluid flow conditions near the solid/liquid interface. In this project, we utilize a novel crystal growth technique called Axial Heat Processing (AHP) that uses a baffle, positioned inside the melt near the interface, to supply and/or conduct heat axially to the interface. The baffle, which may or may not have a heater encased in it, can promote more stable and planar growth as well as reduce buoyancy driven convection. The latter is because the baffle reduces the aspect ratio of the melt as it separates the melt into three sections, above the baffle, in the feed gap between the baffle and the crucible wall, and below the baffle between the baffle base and the interface. AHP also enables a close monitoring and/or control of thermal boundaries near the solid/liquid interface during crystal growth by means of thermocouples placed in the baffle. The interface is kept planar when a heating element in the baffle is used. However, a proper choice of melt height is necessary to keep the interface planar when using the baffle without a heater. This study addresses the influence of melt height and growth velocity on the segregation profile of AHP-grown Sb doped Ge single crystals.

Abbaschian, Reza↗

NASA NTRS2001

In Situ Monitoring of Crystal Growth Using Mephisto

Experiments were carried out to study the morphological stability of Bi-1atomic% Sn alloys using the MEPHISTO directional solidification apparatus aboard Space Shuttle Columbia (STS-87, launched November 19, 1997). The research program involved collaboration of the University of Florida, Centre National d'Etudes Spatiales (France), NASA/Glenn Research Center, the National Institute of Standards and Technology, and the University of New South Wales (Australia). The experiments made use of the Seebeck technique to measure the interface temperature, the resistance change across the sample for determination of the interface velocity, and Peltier current pulsing for demarcation of the interface shape. These data were obtained in real-time during various melting/solidification cycles, and the experiments were controlled via telecommands. The Seebeck signal and temperature measurements in the space experiments, as well as morphological behavior of the solid/liquid interface, were found to be significantly different than those obtained from ground-based studies. For the space-based experiments, interface breakdown was observed at growth velocities of 6.7, 27, and 40 micrometers/s, but not at 1.8 and 3.3 micrometers/s. The results further indicate that the morphological stability threshold for some grain orientations is significantly enhanced, resulting in a staggered planar to cellular transition front. This report summarizes some of these findings.

Abbaschian, Reza↗

NASA NTRS1998

A Numerical Study of Directional Solidification and Melting in Microgravity

A computational model is presented for the study of the solidification and melting of a pure substance and of a binary alloy. The enthalpy method has been used, and incorporated into a commercial CFD code. Three examples of the use of the model are described: the three-dimensional solidification of a pure substance (succinonitrile), the results of which are compared with experiment; an example of the solidification of a bismuth-tin alloy; and a simulation of a solidification and melting experiment done in space known as the MEPHISTO program.

Chen, P. Y. P.↗

NASA NTRS1994

Squeeze film dampers with oil hole feed

To improve the damping capability of squeeze film dampers, oil hole feed rather than circumferential groove feed is a practical proposition. However, circular orbit response can no longer be assumed, significantly complicating the design analysis. This paper details a feasible transient solution procedure for such dampers, with particular emphasis on the additional difficulties due to the introduction of oil holes. It is shown how a cosine power series solution may be utilized to evaluate the oil hole pressure contributions, enabling appropriate tabular data to be compiled. The solution procedure is shown to be applicable even in the presence of flow restrictors, albeit at the expense of introducing an iteration at each time step. Though not of primary interest, the procedure is also applicable to dynamically loaded journal bearings with oil hole feed.

Chen, P. Y. P.↗