Engineering topics

Chen, Qiyi

Publications and source records attributed to Chen, Qiyi.

16 records

DOE OSTI2023

Correlating viscosity and die swell in 3D printing of polyphenylsulfone: A thermo-mechanical optimization modus operandi

Additive manufacturing (AM) of polyphenylsulfone (PPSU), an amorphous high-performance polymer (HPP), has shown promise in exhibiting structural integrity for many applications. With thermoplastic material extrusion 3D printing, parts consisting of layered melts exhibited voids, where the adhesion quality and void size depend on the processing parameters implemented during printing. However, the structure-process-property (SPP) relationships between the thermal properties and rheological and mechanical behavior of AM PPSU are poorly understood. Here, in this study, a comprehensive analysis of the thermal, thermo-mechanical, and layer-by-layer build-up of PPSU is investigated and correlated with viscosity and extrudate die swell behavior with void fraction volume as confirmed by high-resolution x-ray computed tomography (XCT). Gas chromatography–mass spectrometry (GC–MS) pyrolysis confirmed PPSU composition and degradation at 480 °C, consistent with thermo-gravimetric analysis TGA. A 141% difference in viscosity was observed when processing temperatures increased from 350 °C to 400 °C. Likewise, extrudate die swell decreased with increasing temperatures, resulting in a 17% difference. Tensile and compressive properties confirmed that higher extruding temperatures resulted in lower porosity and higher mechanical strength. In general, higher extruding temperatures lower the viscosity to allow for stronger cohesion between layers; however, increasing the temperature too high results in a below unity extrudate die swell, reducing mechanical properties. Therefore, to optimize the mechanical integrity of 3D printed amorphous PPSU parts, an increase in the viscosity, near unity of the extrudate die swell, and tempered extrusion temperature are needed.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Additive Manufacturing of Self‐Sensing Carbon Fiber Composites

Carbon fiber-reinforced polymer (CFRP) composites have gained substantial attention across various industries owing to their exceptional mechanical properties and lightweight nature. The emergence of additive manufacturing technologies brings new opportunities to the industry, offering advantages such as design freedom, rapid prototyping, and customization. However, the fabrication of CFRP composites through 3D printing techniques poses challenges pertaining to low resolution and limitations in complex geometry realization. This work introduces digital light processing printing as a versatile, high-resolution method ideal for CFRP composite fabrication. Furthermore, the development and characterization of CFRP are focused on and the manipulation of mechanical properties through variations in matrix resins and fiber loadings is investigated, showcasing the versatility of CFRP composites for tailored applications. Additionally, the integration of self-sensing capabilities in CFRP structures is explored, which opens up opportunities for applications in smart components for automotive and structural health monitoring.

carbon fiber composites↗

DOE OSTI2023

Well-Tunable, 3D-printable, and Fast Autonomous Self-Healing Elastomers

Self-healing elastomers provide extended longevity of functional materials, due to their unique adaptability and durability. However, a major scientific challenge remains in developing materials with a rapid healing process combined with decent mechanical properties, that can be prepared by a relatively simple synthesis approach. Herein, we report a versatile design approach on self-healing elastomers by incorporating two different hydrogen bonding containing monomers, i.e., 2-[[(butylamino)carbonyl]oxy]ethyl acrylate (BCOE) and 2-ureido-4[1H]pyrimidinone (UPy) functionalized ethyl methacrylate. Poly(BCOE-r-UPy)s are synthesized by reversible addition-fragmentation chain-transfer (RAFT) polymerization, and controlling the ratio of two monomers enables well-tunable mechanical properties with tensile strength ranging from 0.04 to 6.3 MPa and tensile strain up to 3,000 %. The characteristic dissociation energy is calculated from a temperature dependence of terminal relaxation followed by subtracting the segmental relaxation. The rapid autonomous self-healing is achieved when the molar composition of Poly(BCOE-r-UPy) is tailored to BCOE/UPy = 99/1. The self-healing process is monitored in situ by a helium-ion microscope, and its macroscopic study using tensile tests indicates that Poly(BCOE-r-UPy1) with 1 % molar ratio of UPy recovers 70 % of its original toughness at ambient temperature within 10 mins. 3D printing of Poly(BCOE-r-UPy) affords a self-healable 3D structure, demonstrating the adaptability of Poly(BCOE-r-UPy) for on-demand fabrication. The simplicity of synthesis, well-tunable mechanical properties, unique self-healability, and 3D printing capability of Poly(BCOE-r-UPy)s indicate their potential for a range of applications.

36 MATERIALS SCIENCE↗

DOE OSTI2023

An innovative carbonated cementitious material and its printability and carbon mineralization capacity

The main goal of this research is to develop a carbonated cementitious material (CCMs) mix design and demonstrate its rapid stiffening for manufacturing 3D printed or precast elements for building construction (i.e., concrete with enhanced durability and CO 2 capture efficiency). The material development employs hydrated Ca(OH) 2 , and its distinct reaction with CO 2 to form CaCO 3 . Different formulations and additives including polymer materials enable the thermomechanical properties that give these CCMs 3D printability comparable with cement materials used for similar applications. Here, printable and castable CCM formulations were successfully developed and demonstrated to mineralize CO 2 to form up to 57% CaCO 3 .

36 MATERIALS SCIENCE↗

DOE OSTI2023

On the 3D printing of polypropylene and post-processing optimization of thermomechanical properties

Polypropylene (PP) is a highly desirable polyolefin in various plastic industries due to its outstanding thermomechanical properties and chemical resistance. Therefore, the 3D printing of PP is an interesting avenue to explore in digitized manufacturing, where more freedom in structural designs is available for new and extended applications, such as high-performance engineering parts. Here, in this work, we 3D printed PP and studied the effect of printing parameters and post-processing conditions on the printed polymer’s thermomechanical behavior. Results showed that nozzle and bed temperatures of 220 and 100°C produced a high printing quality. Infill percentages between 80 and 90%, coupled with a 4-h annealing at 110ºC, also resulted in optimal printed properties. It is thought that PP can be potentially blended with polyethylene or other vinyl polymers for a more extended 3D printing utility and practical applications in rapid tooling and prototyping.

36 MATERIALS SCIENCE↗

DOE OSTI2023

On the 3D printability of silicone-based adhesives via viscous paste extrusion

Silicone, a commonly used household and construction adhesive, filler, or sealant, is also known for its flexibility, thermal stability, and insulating properties. It is viable as a conformally 3D-printed elastomeric matrix for flexible electronics and biomedical applications. Since most of the popular 3D printing methods use precise print specifications and defined resolution, this study explored the 3D printability of commercial silicone adhesives via a paste extrusion setup. Its viscoelastic and composition properties including the dimensional accuracy and mechanical properties of printed objects using controlled print parameters have been investigated. Finally, these experimental processes in 3D printing should pave the way in using materials originally intended for household use.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Mechanically and Thermally Enhanced 3D-Printed Photocurable Polymer Nanocomposites Containing Functionalized Chitin Nanowhiskers by Stereolithography

Additive manufacturing, or simply 3D printing (3DP), where objects are built through layer-wise material deposition, has gained significant academic and industrial attention as a result of the development of advanced and functional materials requiring rapid, customized, and flexible solutions. In the context of green manufacturing, diversifying environmentally and economically sustainable material portfolios is an essential endeavor for the success of 3DP technology that uses widely available, highly valuable, and renewable materials. Here, we used stereolithography (SLA) for processing methacrylate-based photocurable resins containing crab shell-derived chitin nanowhiskers (CNWs), which are surface-functionalized by reactive acrylate groups. Results from full spectral, thermal, structural, and topological analyses corroborate not only the surface functionalization of CNWs but also indicate the presence of these photocurable CNW (pCNW) fillers in the 3D-printed nanocomposites. Owing to the strong interfacial bond induced by the physical and chemical crosslinking between the pCNW and methacrylate (MA) polymer matrix, the internally formulated nanocomposites displayed enhanced thermomechanical properties (e.g., storage modulus and glass transition temperature) compared to those of commercially available pure SLA resins. For instance, the inclusion of 0.5 wt % pCNW improved the tensile strength and stiffness to up to 78 and 71%, respectively, without compromising the toughness and ductility of the printed material. Accordingly, this result also evidences the compatibility between the filler and resin materials. Consequently, the formation of a crosslinked network in the nanocomposite structure results in a higher thermal stability and activation energy (i.e., up to ~79%) for all the hybrid materials than the pristine MA. Finally, the high-resolution SLA print features, dimensional accuracy, and enhanced mechanical performance of our microstructure-forming functionalized chitin-based nanocomposites make them promising materials for a wide range of robust and high-performance industrial applications.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Characterize traction–separation relation and interfacial imperfections by data-driven machine learning models

Abstract Interfacial mechanical properties are important in composite materials and their applications, including vehicle structures, soft robotics, and aerospace. Determination of traction–separation (T–S) relations at interfaces in composites can lead to evaluations of structural reliability, mechanical robustness, and failures criteria. Accurate measurements on T–S relations remain challenging, since the interface interaction generally happens at microscale. With the emergence of machine learning (ML), data-driven model becomes an efficient method to predict the interfacial behaviors of composite materials and establish their mechanical models. Here, we combine ML, finite element analysis (FEA), and empirical experiments to develop data-driven models that characterize interfacial mechanical properties precisely. Specifically, eXtreme Gradient Boosting (XGBoost) multi-output regressions and classifier models are harnessed to investigate T–S relations and identify the imperfection locations at interface, respectively. The ML models are trained by macroscale force–displacement curves, which can be obtained from FEA and standard mechanical tests. The results show accurate predictions of T–S relations ( R 2 = 0.988) and identification of imperfection locations with 81% accuracy. Our models are experimentally validated by 3D printed double cantilever beam specimens from different materials. Furthermore, we provide a code package containing trained ML models, allowing other researchers to establish T–S relations for different material interfaces.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2021

Highly Recyclable, Mechanically Isotropic and Healable 3D-Printed Elastomers via Polyurea Vitrimers

Delamination of three-dimensional (3D) printed polymer materials by fused deposition modeling (FDM) is a long-standing challenge in additive manufacturing (AM). With numerous efforts devoted to modification of commercially available thermoplastic FDM filaments, developing printing polymeric materials with new chemical design that could intrinsically improve interlayer adhesion, especially combined with other benefits, is in high demand. Herein, we developed a polyurea vitrimer with heat-driven malleability, which is printed to different 3D geometries using FDM. Significantly improved interlayer adhesion was observed by post-annealing the printed samples close to its topology-freezing transition temperature upon which fast associative dynamic covalent bonds exchange reaction occurs. Isotropic mechanical properties were achieved as demonstrated with printed tensile samples with different infill directions. Finally, the printed materials could be fully recycled for five generations with retained mechanical properties. Furthermore, the mechanical performance of the printed sample could also be repaired after damage.

36 MATERIALS SCIENCE↗

DOE OSTI2021

On the additive manufacturing (3D printing) of viscoelastic materials and flow behavior: From composites to food manufacturing

Additive manufacturing (AM) or more commonly known as 3D-printing has gained much ground in industrial manufacturing because of its breakthrough in rapid prototyping and processes. To date, the 3D-printing market has grown significantly and is poised for growth in line with digitization of manufacturing. Furthermore, the main objective of this review article focuses on the viscoelastic behavior (viscous solution) of 3D printing materials at ambient conditions, which are not essentially under melt-flow or higher temperatures. The initial section reviews the basic concepts on viscosity and viscoelastic phenomenon, with emphasis on the preferred conditions a viscous material should have prior to 3D-printing. Several examples of structures formed from viscoelastic materials through 3D-printing are also detailed, as well as the various curing techniques for different printed objects or models. While there is much interest on industrial applications, the last part surveys various food formulations used for 3D-printing.

36 MATERIALS SCIENCE↗

DOE OSTI2021

3D printing of biomedically relevant polymer materials and biocompatibility

Research on polymer materials for additive manufacturing technology in biomedical applications is as promising as it is numerous, but biocompatibility of printable materials still remains a big challenge. Changes occurring during the 3D-printing processes itself may have adverse effects on the compatibility of the completed print. Furthermore, this prospective will put emphasis on the different additives and processes that can have a direct impact on biocompatibility during and after 3D printing of polymer materials.

36 MATERIALS SCIENCE↗

DOE OSTI2021

High performance polymers for oil and gas applications

Proper material selection has been one of the most important aspects in the design of chemical process equipment. In particular, the oil and gas industry has transitioned from using metals to non-metals (e.g. advanced and high performance polymeric materials) in most of their structural components, coatings, equipment parts, and the like. It is therefore imperative to understand the advantages and limitations of these polymer materials before they can be effectively used for a specific application. This review article aims to provide an overview of the properties, applications, and durability against reactivity and degradation of high performance polymers commonly used in the oil and gas industry. These include polysulfone, polyetherimide, polyphenylene sulfide, polyetheretherketone, fluoropolymers, and other high performance thermosets, elastomers, and polymer nanocomposites. Further, this article covers the current research efforts in improving the properties of high performance polymers and expanding their applications (including 3D printing or additive manufacturing) in the oil and gas industry.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Additive manufacturing for COVID-19: Devices, materials, prospects, and challenges

The current COVID-19 pandemic has caused the shortage of personal protective equipment (PPE) where improvised manufacturing in particular 3D printing has addressed many needs. This prospective discusses the current global crisis, then follows the wide interest in addressing the shortage of medical devices and PPEs used for treatment and protection against pathogens. An overview of the 3D printing process with polymer materials is given followed by the different 3D printing projects of PPEs and medical devices that emerged for the pandemic (including validation/testing). The potential for rapid prototyping with different polymer materials and eventual high-throughput production is emphasized.

36 MATERIALS SCIENCE↗

DOE OSTI2020

On the Use of Surfactant-Complexed Chitosan for Toughening 3D Printed Polymethacrylate Composites

This work reports a simple approach to prepare toughened 3D-printed polymethacrylate (PMA) composites using surfactant-modified chitosan (SMCS) particles at loadings between 2–10 wt%. Chitosan (CS) is modified with anionic surfactant, sodium dodecyl sulfate, via ionic complexation to facilitate compatibility and dispersion of CS to PMA matrix by non-covalent interactions between the components. The study successfully demonstrates high-accuracy 3D printing of composites with significant improvements in the overall mechanical properties. The composite with the best loading of 8 wt% SMCS shows a tensile modulus of 1.23 ± 0.05 GPa, a tensile strength at 49.8 ± 0.96 MPa, a yield stress at 33.3 ± 1.48 MPa, and a strain-at-ailure 10.3 ± 0.61%, which are 45%, 40%, 32%, and 68% higher than neat PMA, respectively. This provides a significant improvement in toughness at 4.92 ± 0.55 MJ m -3 for the composite, 184% higher than that of neat PMA. The marked increase in toughness is due to enhanced filler-matrix interactions which improve the ability of the 3D printed composite to absorb energy under tensile load. The results from this work provide new understandings into the strategies for design and preparation of stereolithography 3D printed materials reinforced with toughening fillers from renewable resources.

36 MATERIALS SCIENCE↗

DOE OSTI2020

A Dual Approach in Direct Ink Writing of Thermally Cured Shape Memory Rubber Toughened Epoxy

Bisphenol A-based epoxies are much used in a wide range of composite and coating applications due to their excellent thermomechanical properties. However, their 3D printability remains a challenge with most reported materials suffering from high brittleness and low toughness. In this work, we have described especially modified epoxy resins that enable 3D printing with both fast and slow curing rates. These materials exhibit greatly enhanced toughness, tunable thermomechanical properties, and excellent shape memory behavior. Two different printing systems, including a two-part static mixing printhead and a single extrusion printhead, were developed for fast- and slow-curing epoxies, respectively. The rheology of inks in both systems has been modified into printable thixotropic fluids with the aid of silica nanoparticles and other additives. Epoxide-functionalized telechelic polybutadiene was added into the resins, which are then introduced inside the epoxy network after cross-linking. The addition of polybutadiene rubber significantly improves the toughness (over 135%), fracture strain (over 200%), and shape memory behavior. By adding different amounts of the rubber telechelic, thermomechanical properties, including modulus, elongation, and Tg of epoxy, can be well controlled in a wide range to satisfy different applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

4D Printing via an Unconventional Fused Deposition Modeling Route to High-Performance Thermosets

An unprecedented four-dimensional (4D) printing process allowing high-performance and shape memory thermoset to be printed, for the first time, by fused deposition modeling (FDM) with isotropic properties has been achieved. Here, bisphenol A-based epoxy and benzoxazine were formulated to a low-temperature thermoplastic and high-temperature thermoset resin, which is melt-extrudable and can be postcured into covalently cross-linked material. Carbon nanotube (CNT) was added in the resin to work as both mechanical enhancement filler and rheology modifier to prevent shape deformation during postcuring process. The cross-layer reaction fuses individual layers into an integrity, thus eliminating layer delamination induced by FDM, offering isotropic mechanical properties regardless of the printing orientations. The highly cross-linked network provides outstanding mechanical strength and superb thermal stability. The excellent shape memory performance with fast recovery rate and large recovery degree is also obtained in the three-dimensional (3D) printed composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗