Search NASA⌕ Search

Engineering topics

Chen, Shangshang

Publications and source records attributed to Chen, Shangshang.

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Bifacial all-perovskite tandem solar cells

The efficiency of all-perovskite tandem devices falls far below theoretical efficiency limits, mainly because a widening bandgap fails to increase open-circuit voltage. We report on a bifacial all-perovskite tandem structures with an equivalent efficiency of 29.3% under back-to-front irradiance ratio of 30. This increases energy yield and reduces the required bandgap of a wide-bandgap cell. Open-circuit voltage deficit is therefore minimized, although its performance under only front irradiance is not ideal. The bifacial device needs a sputtered rear transparent electrode, which could reduce photon path length and deteriorate stability of Pb-Sn perovskites. Embedding a light-scattering micrometer-sized particle layer into perovskite to trap light, effectively increases absorptance by 5 to 15% in the infrared region. Using a nonacidic hole transport layer markedly stabilizes the hole-extraction interface by avoiding proton-accelerated formation of iodine. These two strategies together increase efficiency of semitransparent Pb-Sn cells from 15.6 to 19.4%, enabling fabrication of efficient bifacial all-perovskite tandem devices.

14 SOLAR ENERGY↗
DOE OSTI2022

Efficient monolithic all-perovskite tandem solar modules with small cell-to-module derate

All-perovskite tandem solar modules are promising to reduce the cost of photovoltaic systems with their high efficiency and solution fabrication, but their sensitivity to air still imposes a great challenge. Here a hot gas-assisted blading method is developed to accelerate the perovskite solidification, forming compact and thick narrow bandgap (NBG) perovskite films. Adding a reduction agent into NBG films followed by a short period of air exposure and a post-fabrication storage surprisingly increases carrier recombination lifetime and enables laser scribing in ambient conditions without obvious loss of device performance. This combination suppresses tin and iodide oxidation and forms a thin SnO 2 layer on the NBG film surface. Monolithic all-perovskite tandem solar modules showed a champion efficiency of 21.6% with a 14.3 cm 2 aperture area, corresponding to an active area efficiency of 23.0%. Lastly, the very small cell-to-module derate of 6.5% demonstrates the advantage of a tandem monolithic structure for solar modules.

14 SOLAR ENERGY↗
DOE OSTI2022

Gradient Doping in Sn–Pb Perovskites by Barium Ions for Efficient Single-Junction and Tandem Solar Cells

Narrow bandgap tin-lead (NBG Sn-Pb) perovskites generally have a high density of unintentional p-type self-doping, which reduces the charge carrier lifetimes, diffusion lengths and device efficiencies. Here, we demonstrate a p-n homojunction across the Sn-Pb perovskite resulted from a gradient doping by Ba 2+ . We report that 0.1 mol% Ba 2+ can effectively compensate the p-doping of Sn-Pb perovskites or even turns it to n-type without changing its bandgap. Ba 2+ cations are found to stay at the interstitial sites and work as shallow electron donor. In addition, Ba 2+ cations show a unique heterogeneous distribution in perovskite film. Most of the barium ions stay in the top 600 nanometer region of the perovskite films and turn it into weakly n-type, while the bottom portion of the film remains to be p-type. The gradient doping forms of a homojunction from top to bottom of the perovskite films with a built-in field that facilitates extraction of photogenerated carriers, resulting an increased carrier extraction length. Furthermore, this strategy enhanced the efficiency of Sn-Pb perovskite single-junction solar cells to over 21.0% and boosted the efficiencies of monolithic perovskite-perovskite tandem solar cells to 25.3% and 24.1%, for active areas of 5.9 mm2 and 0.94 cm 2 , respectively.

14 SOLAR ENERGY↗
DOE OSTI2021

Stabilizing perovskite-substrate interfaces for high-performance perovskite modules

The interfaces of perovskite solar cells (PSCs) are important in determining their efficiency and stability, but the morphology and stability of imbedded perovskite-substrate interfaces have received less attention than have top interfaces. We found that dimethyl sulfoxide (DMSO), which is a liquid additive broadly applied to enhance perovskite film morphology, was trapped during film formation and led to voids at perovskite-substrate interfaces that accelerated the film degradation under illumination. Partial replacement of DMSO with solid-state carbohydrazide reduces interfacial voids. A maximum stabilized power conversion efficiency (PCE) of 23.6% was realized for blade-coated p-type/intrinsic/n-type (p-i-n) structure PSCs with no efficiency loss after 550-hour operational stability tests at 60°C. The perovskite mini-modules showed certified PCEs of 19.3 and 19.2%, with aperture areas of 18.1 and 50.0 square centimeters, respectively.

Chen, Shangshang↗
DOE OSTI2021

Regio‐Regular Polymer Acceptors Enabled by Determined Fluorination on End Groups for All‐Polymer Solar Cells with 15.2 % Efficiency

Abstract Polymerization sites of small molecule acceptors (SMAs) play vital roles in determining device performance of all‐polymer solar cells (all‐PSCs). Different from our recent work about fluoro‐ and bromo‐ co‐modified end group of IC‐FBr (a mixture of IC‐FBr1 and IC‐FBr2), in this paper, we synthesized and purified two regiospecific fluoro‐ and bromo‐ substituted end groups (IC‐FBr‐ o & IC‐FBr‐ m ), which were then employed to construct two regio‐regular polymer acceptors named PYF‐T‐ o and PYF‐T‐ m , respectively . In comparison with its isomeric counterparts named PYF‐T‐ m with different conjugated coupling sites, PYF‐T‐ o exhibits stronger and bathochromic absorption to achieve better photon harvesting. Meanwhile, PYF‐T‐ o adopts more ordered inter‐chain packing and suitable phase separation after blending with the donor polymer PM6, which resulted in suppressed charge recombination and efficient charge transport. Strikingly, we observed a dramatic performance difference between the two isomeric polymer acceptors PYF‐T‐ o and PYF‐T‐ m . While devices based on PM6:PYF‐T‐ o can yield power conversion efficiency (PCE) of 15.2 %, devices based on PM6:PYF‐T‐ m only show poor efficiencies of 1.4 %. This work demonstrates the success of configuration‐unique fluorinated end groups in designing high‐performance regular polymer acceptors, which provides guidelines towards developing all‐PSCs with better efficiencies.

Yu, Han↗
DOE OSTI2021

Regio‐Regular Polymer Acceptors Enabled by Determined Fluorination on End Groups for All‐Polymer Solar Cells with 15.2 % Efficiency

Abstract Polymerization sites of small molecule acceptors (SMAs) play vital roles in determining device performance of all‐polymer solar cells (all‐PSCs). Different from our recent work about fluoro‐ and bromo‐ co‐modified end group of IC‐FBr (a mixture of IC‐FBr1 and IC‐FBr2), in this paper, we synthesized and purified two regiospecific fluoro‐ and bromo‐ substituted end groups (IC‐FBr‐ o & IC‐FBr‐ m ), which were then employed to construct two regio‐regular polymer acceptors named PYF‐T‐ o and PYF‐T‐ m , respectively . In comparison with its isomeric counterparts named PYF‐T‐ m with different conjugated coupling sites, PYF‐T‐ o exhibits stronger and bathochromic absorption to achieve better photon harvesting. Meanwhile, PYF‐T‐ o adopts more ordered inter‐chain packing and suitable phase separation after blending with the donor polymer PM6, which resulted in suppressed charge recombination and efficient charge transport. Strikingly, we observed a dramatic performance difference between the two isomeric polymer acceptors PYF‐T‐ o and PYF‐T‐ m . While devices based on PM6:PYF‐T‐ o can yield power conversion efficiency (PCE) of 15.2 %, devices based on PM6:PYF‐T‐ m only show poor efficiencies of 1.4 %. This work demonstrates the success of configuration‐unique fluorinated end groups in designing high‐performance regular polymer acceptors, which provides guidelines towards developing all‐PSCs with better efficiencies.

Yu, Han↗
DOE OSTI2021

Ligand assisted growth of perovskite single crystals with low defect density

A low defect density in metal halide perovskite single crystals is critical to achieve high performance optoelectronic devices. Here we show the reduction of defect density in perovskite single crystals grown by a ligand-assisted solution process with 3-(decyldimethylammonio)-propane-sulfonate inner salt (DPSI) as an additive. DPSI ligands anchoring with lead ions on perovskite crystal surfaces not only suppress nucleation in solution, but also regulate the addition of proper ions to the growing surface, which greatly enhances the crystal quality. The grown CH 3 NH 3 PbI 3 crystals show better crystallinity and a 23-fold smaller trap density of 7 × 10 10 cm -3 than the optimized control crystals. The enhanced material properties result in significantly suppressed ion migration and superior X-ray detection sensitivity of CH 3 NH 3 PbI 3 detectors of (2.6 ± 0.4) × 10 6 µC Gy -1 air cm -2 for 60 kVp X-ray and the lowest detectable dose rate reaches (5.0 ± 0.7) nGy s -1 , which enables reduced radiation dose to patients in medical X-ray diagnostics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Crystallization in one-step solution deposition of perovskite films: Upward or downward?

Despite the fast progress of perovskite photovoltaic performances, understanding the crystallization and growth of perovskite films is still lagging. One unanswered fundamental question is whether the perovskite films are grown from top (air side) to bottom (substrate side) or from bottom to top despite 10 years of development. Here, by using grazing incidence x-ray diffraction and morphology characterizations, we unveil that the perovskite films prepared by one-step solution processes, including antisolvent-assisted spin coating and blade coating, follow the downward growth from intermediate phase during thermal annealing. Such a top-to-bottom downward growth is initialized by the evaporation of residual solvent from the top surface of “wet” films and is less sensitive to perovskite compositions and the wettability of underlying substrates. Addressing this fundamental question is important to understand the heterogeneity of perovskite films along the vertical direction, which markedly affects the efficiency and stability of perovskite solar cells.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultrafast Exciton Transport with a Long Diffusion Length in Layered Perovskites with Organic Cation Functionalization

Abstract Layered perovskites have been employed for various optoelectronic devices including solar cells and light‐emitting diodes for improved stability, which need exciton transport along both the in‐plane and the out‐of‐plane directions. However, it is not clear yet what determines the exciton transport along the in‐plane direction, which is important to understand its impact toward electronic devices. Here, by employing both steady‐state and transient photoluminescence mapping, it is found that in‐plane exciton diffusivities in layered perovskites are sensitive to both the number of layers and organic cations. Apart from exciton–phonon coupling, the octahedral distortion is revealed to significantly affect the exciton diffusion process, determined by temperature‐dependent photoluminescence, light‐intensity‐dependent time‐resolved photoluminescence, and density function theory calculations. A simple fluorine substitution to phenethylammonium for the organic cations to tune the structural rigidity and octahedral distortion yields a record exciton diffusivity of 1.91 cm 2 s −1 and a diffusion length of 405 nm along the in‐plane direction. This study provides guidance to manipulate exciton diffusion by modifying organic cations in layered perovskites.

Xiao, Xun↗