Engineering topics

Chen, Y. K.

Publications and source records attributed to Chen, Y. K..

12 records

NASA NTRS2012

Thermal Analysis of Small Re-Entry Probe

The Small Probe Reentry Investigation for TPS Engineering (SPRITE) concept was developed at NASA Ames Research Center to facilitate arc-jet testing of a fully instrumented prototype probe at flight scale. Besides demonstrating the feasibility of testing a flight-scale model and the capability of an on-board data acquisition system, another objective for this project was to investigate the capability of simulation tools to predict thermal environments of the probe/test article and its interior. This paper focuses on finite-element thermal analyses of the SPRITE probe during the arcjet tests. Several iterations were performed during the early design phase to provide critical design parameters and guidelines for testing. The thermal effects of ablation and pyrolysis were incorporated into the final higher-fidelity modeling approach by coupling the finite-element analyses with a two-dimensional thermal protection materials response code. Model predictions show good agreement with thermocouple data obtained during the arcjet test.

Agrawal, Parul↗

NASA NTRS2009

Cassini/Huygens Probe Entry, Descent, and Landing (EDL) at Titan Independent Technical Assessment

Starting in January 2004, the NESC has received several communications from knowledgeable technical experts at NASA expressing shared concerns (mainly at the Langley Research Center (LaRC) and Ames Research Center (ARC)) about Huygens mission success. It was suggested that NASA become more technically involved directly in the analysis of Huygens' entry, descent and landing (EDL) focusing on the parachute deployment trigger performance and the resultant effects on the operation of the parachute system, and the determination of the radiative heating environment at Titan by ESA and the corresponding thermal protection system (TPS) response. A NESC Team was formed and tasked to provide an independent assessment of these concerns. The results of that assessment are documented in this report.

Powell, Richard W.↗

NASA NTRS2006

Systems Analysis for a Venus Aerocapture Mission

Previous high level analysis has indicated that significant mass savings may be possible for planetary science missions if aerocapture is employed to place a spacecraft in orbit. In 2001 the In-Space Propulsion program identified aerocapture as one of the top three propulsion technologies for planetary exploration but that higher fidelity analysis was required to verify the favorable results and to determine if any supporting technology gaps exist that would enable or enhance aerocapture missions. A series of three studies has been conducted to assess, from an overall system point of view, the merit of using aerocapture at Titan, Neptune and Venus. These were chosen as representative of a moon with an atmosphere, an outer giant gas planet and an inner planet. The Venus mission, based on desirable science from plans for Solar System Exploration and Principal Investigator proposals, to place a spacecraft in a 300km polar orbit was examined and the details of the study are presented in this paper.

Lockwood, Mary Kae↗

NASA NTRS2005

Nanostructured Thermal Protection Systems for Space Exploration Missions

Strong research and development programs in nanotechnology and Thermal Protection Systems (TPS) exist at NASA Ames. Conceptual studies have been undertaken to determine if new, nanostructured materials (composites of existing TPS materials and nanostructured composite fibers) could improve the performance of TPS. To this end, we have studied various candidate heatshields, some composed of existing TPS materials (with known material properties), to provide a baseline for comparison with others that are admixtures of such materials and a nanostructured material. In the latter case, some assumptions were made about the thermal conductivity and strength of the admixture, relative to the baseline TPS material. For the purposes of this study, we have made the conservative assumption that only a small fraction of the remarkable properties of carbon nanotubes (for example) will be realized in the material properties of the admixtures employing them. The heatshields studied included those for Sharp leading edges (appropriate to out-of-orbit entry and aero-maneuvering), probes, an out-of-orbit Apollo Command Module (as a surrogate for NASA's new Crew Exploration Vehicle [CEV]), a Mars Sample Return Vehicle and a large heat shield for Mars aerocapture missions. We report on these conceptual studies, which show that in some cases (not all), significant improvements in the TPS can be achieved through the use of nanostructured materials.

Arnold, J. O.↗

NASA NTRS1997

Thermal Response and Ablation Programs for TPS Sizing Computation

The computer programs developed at NASA Ames Research Center for TPS sizing computation have been applied to many NASA's space missions, such as Mars Pathfinder, StarDust, Mars 2001, DS-II, and Saturn Entry Probe. These computer programs include FIAT (Fully Implicit Ablation and Thermal Response Program, MAT (Multi-component Ablation Thermochemistry Program), TPSX (Thermal Protection Systems Expert & Material Properties Database), and TPSGui (Thermal Protection Systems Graphical User Interface). For most planetary missions, the aerothermodynamics and material response are strongly coupled; thus a closed loop iteration technique between the FIAT and CFD (Computational Fluid Dynamics) codes has been developed to obtain the high fidelity bench mark TPS sizing solution. The computer codes and predictive methods are presented and discussed in detail.

Chen, Y. K.↗

NASA NTRS1997

Analysis of Mars Pathfinder Entry Data, Aerothermal Heating, and Heat Shield Material Response

The Mars Pathfinder heatshield contained several thermocouples and resistance thermometers. A description of the experiment, the entry data, and analysis of the entry environment and material response is presented. In particular, the analysis addresses uncertainties of the data and the fluid dynamics and material response models. The calculations use the latest trajectory and atmosphere reconstructions for the Pathfinder entry. A modified version of the GIANTS code is used for CFD (computational fluid dynamics) analyses, and FIAT is used for material response. The material response and flowfield are coupled appropriately. Three different material response models are considered. The analysis of Pathfinder entry data for validation of aerothermal heating and material response models is complicated by model uncertainties and unanticipated data-acquisition and processing problems. We will discuss these issues as well as ramifications of the data and analysis for future Mars missions.

Milos, Frank↗

NASA NTRS1997

Fully Implicit Ablation and Thermal Response Program for Spacecraft Heatshield Analysis

A fully implicit ablation and thermal response program has been developed for the simulation of one-dimensional transient transport of thermal energy in a multilayer stack of isotropic materials and structure which can ablate from a front surface and decompose in-depth. Equations and numerical procedures for solution are described. Solutions are compared with those of Aerotherm Charring Material Thermal Response and Ablation Program, and with the arcjet data. The code is numerically more stable, and solves much wider range of problems compared with the existing explicit code. Applications of the code for the analysis of aeroshell heatshields of Stardust, Mars 2001, and Mars Microprobe using the advanced Light Weight Ceramic Ablators developed at the NASA Ames Research Center are presented and discussed in detail.

Chen, Y. K.↗

NASA NTRS1995

Analysis of Aerothermal Heating Over Reusable Single-Stage to Orbit Vehicles

Using the General Aerodynamic Simulation Program (GASP) with finite-rate surface catalysis and radiative equilibrium surface temperature conditions, a computational study has been conducted to predict three-dimensional aero-convective heating over the proposed reusable single-stage to orbit vehicles. The solutions for three basic classes of usable single-stage-to-orbit vehicles, including wing body, lifting body and vertical lander, are presented and compared to provide information for vehicle design. The free stream conditions used in this study occur at an altitude of 57.5 km, ambient density of 4.129e-4 kg/cubic m, and velocity of 4,849 m/s. The convective heating over the vehicle surface in both laminar and turbulent flow regimes were computed. The Baldwin-Lomax algebraic model with a modified van Driest damping factor was applied in the turbulent flow calculations. A bifurcation model which guarantees the conservation of mass diffusive fluxes was adopted to account for the multi-species mass diffusion. The effects of turbulence and surface catalysis on the surface heating are discussed in detail The solutions indicate the degree of oxygen dissociation over the leeward side is sensitive to the shape of vehicle body. Predicted convective heating over the entire surface of lifting body is strongly affected by the presence of surface catalysis. For wing body and vertical lander, the surface catalysis effect does not appear to be important in the far downstream region, and turbulence is the dominant effect on the heating prediction in this region.

Chen, Y. K.↗

NASA NTRS1995

Ames Research Center Mars/Pathfinder Heat Shield Design Verification ARC-JET Test

Design verification tests were performed on samples representing the aerobrake of the Mars/Pathfinder vehicle. The test specimens consisted of the SLA-561V ablator bonded to the honeycomb structure. The primary objective was to evaluate the ablation materials performance and to measure temperatures within the ablator, at the structural bondline and at the back sheet of the honeycomb structure. Other objectives were to evaluate the effect of ablative repair plug material treatment and voids in the heat shield. A total of 29 models were provided for testing in the Ames 60MW arc-jet facility. Of these, 23 models were flat-faced and six remaining models were curved edge ones, intended to simulate the conditions on the curved rim of the forebody where the maximum shear occurred. Eight sets of test conditions were used. The stagnation point heating rates varied from 47 to 240 W/cm2 and the stagnation pressures from 0.15 to 0.27 atm. (The maximum flight values are 132 W/cm2 and 0.25 atm) The majority of these runs were made at a nominal stagnation pressure of 0.25 atm. Two higher pressure runs were made to check the current (denser) ablation material for spallation, or other forms of thermal stress failure. Over 60% of the flatfaced models yielded good thermocouple data and all produced useful surface recession information. Of the five curved-edge models that were tested, only one gave good data; the remaining ones experienced model-holder failure. The test results can be summarized by noting that no failure of the ablative material was observed on any model. Also, the bondline temperature design limit of 250 C was never reached within an equivalent flight time despite a stagnation point heat load that exceeded the maximum flight value by up to 130%. At heating rates of over 200W/cm2 and stagnation pressures of 0.25 atm, or greater, the average surface recessions exceeded 0.5 cm on some models. The surface roughness increased dramatically at pressures above 0.25 atm and was four times greater at 0.27 atm than at 0.25 atm. Procured repair plug material performed much better than room-temperature cured plugs, as observed in the previous tests. Voids in the ablator did not increase local temperatures and gaps did not grow during testing.

Tran, Huy K.↗

NASA NTRS1994

Trajectory Based Heating and Ablation Calculations for MESUR Pathfinder Aeroshell

Based on the geometry of Mars Environment Survey (MESUR) Pathfinder aeroshell and an estimated Mars entry trajectory, two-dimensional axisymmetric time dependent calculations have been obtained using GIANTS (Gauss-Siedel Implicit Aerothermodynamic Navier-Stokes code with Thermochemical Surface Conditions) code and CMA (Charring Material Thermal Response and Ablation) Program for heating analysis and heat shield material sizing. These two codes are interfaced using a loosely coupled technique. The flowfield and convective heat transfer coefficients are computed by the GIANTS code with a species balance condition for an ablating surface, and the time dependent in-depth conduction with surface blowing is simulated by the CMA code with a complete surface energy balance condition. In this study, SLA-561V has been selected as heat shield material. The solutions, including the minimum heat shield thicknesses over aeroshell forebody, pyrolysis gas blowing rates, surface heat fluxes and temperature distributions, flowfield, and in-depth temperature history of SLA-561V, are presented and discussed in detail.

Chen, Y. K.↗

NASA NTRS1993

Convective heat-transfer rate distributions over a 140 deg blunt cone at hypersonic speeds in different gas environments

Experiments were conducted in air, CO2, and CO2-argon gas mixtures to obtain heating distribution data over a 140 deg blunt cone with various corner radii. The effect of corner radius on the heating distribution over the forebody of the cone was included in the investigation. These experiments provide data for validation of two-dimensional axisymmetric and three-dimensional Navier-Stokes solutions. Heating distribution data and measured bow shock wave stand-off distances for 0 deg angle of attack were compared with predicted values using a two-dimensional axisymmetric Navier-Stokes code.

Stewart, David A.↗

NASA NTRS1993

Chemical nonequilibrium Navier-Stokes solutions for hypersonic flow over an ablating graphite nosetip

The general boundary conditions including mass and energy balances of chemically equilibrated or nonequilibrated gas adjacent to ablating surfaces have been derived. A computer procedure based on these conditions was developed and interfaced with the Navier-Stokes solver for predictions of the flow field, surface temperature, and surface ablation rates over re-entry space vehicles with ablating Thermal Protection Systems (TPS). The Navier-Stokes solver with general surface thermochemistry boundary conditions can predict more realistic solutions and provide useful information for the design of TPS. A test case with a proposed hypersonic test vehicle configuration and associated free stream conditions was developed. Solutions with various surface boundary conditions were obtained, and the effect of nonequilibrium gas as well as surface chemistry on surface heating and ablation rate were examined. The solutions of the GASP code with complete ablating surface conditions were compared with those of the ASC code. The direction of future work is also discussed.

Chen, Y. K.↗