A Flexible Phosphonate Metal–Organic Framework for Enhanced Cooperative Ammonia Capture
Not provided.
Chemistry↗
Engineering topics
Chen, Yinlin
Publications and source records attributed to Chen, Yinlin.
Trace benzene capture by decoration of structural defects in metal–organic framework materials
Abstract Capture of trace benzene is an important and challenging task. Metal–organic framework materials are promising sorbents for a variety of gases, but their limited capacity towards benzene at low concentration remains unresolved. Here we report the adsorption of trace benzene by decorating a structural defect in MIL-125-defect with single-atom metal centres to afford MIL-125-X (X = Mn, Fe, Co, Ni, Cu, Zn; MIL-125, Ti 8 O 8 (OH) 4 (BDC) 6 where H 2 BDC is 1,4-benzenedicarboxylic acid). At 298 K, MIL-125-Zn exhibits a benzene uptake of 7.63 mmol g −1 at 1.2 mbar and 5.33 mmol g −1 at 0.12 mbar, and breakthrough experiments confirm the removal of trace benzene (from 5 to <0.5 ppm) from air (up to 111,000 min g −1 of metal–organic framework), even after exposure to moisture. The binding of benzene to the defect and open Zn(II) sites at low pressure has been visualized by diffraction, scattering and spectroscopy. This work highlights the importance of fine-tuning pore chemistry for designing adsorbents for the removal of air pollutants.
Chemistry↗
Enhanced Benzene Adsorption in Chloro-Functionalized Metal–Organic Frameworks
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Direct Conversion of Methane to Ethylene and Acetylene over an Iron-Based Metal–Organic Framework
Conversion of methane (CH 4 ) to ethylene (C 2 H 4 ) and/or acetylene (C 2 H 2 ) enables routes to a wide range of products directly from natural gas. However, high reaction temperatures and pressures are often required to activate and convert CH 4 controllably, and separating C 2+ products from unreacted CH 4 can be challenging. Here, we report the direct conversion of CH 4 to C 2 H 4 and C 2 H 2 driven by non-thermal plasma under ambient (25 °C and 1 atm) and flow conditions over a metal–organic framework material, MFM-300(Fe). The selectivity for the formation of C 2 H 4 and C 2 H 2 reaches 96% with a high time yield of 334 μmol g cat –1 h –1 . At a conversion of 10%, the selectivity to C 2+ hydrocarbons and time yield exceed 98% and 2056 μmol g cat –1 h –1 , respectively, representing a new benchmark for conversion of CH 4 . In situ neutron powder diffraction, inelastic neutron scattering and solid-state nuclear magnetic resonance, electron paramagnetic resonance (EPR), and diffuse reflectance infrared Fourier transform spectroscopies, coupled with modeling studies, reveal the crucial role of Fe–O(H)–Fe sites in activating CH 4 and stabilizing reaction intermediates via the formation of an Fe–O(CH 3 )–Fe adduct. In addition, a cascade fixed-bed system has been developed to achieve online separation of C 2 H 4 and C 2 H 2 from unreacted CH 4 for direct use. Integrating the processes of CH 4 activation, conversion, and product separation within one system opens a new avenue for natural gas utility, bridging the gap between fundamental studies and practical applications in this area.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Ultra-fast Proton Conduction and Photocatalytic Water Splitting in a Pillared Metal–Organic Framework
Proton-exchange membrane fuel cells enable the portable utilization of hydrogen (H 2 ) as an energy resource. Current electrolytic materials have limitation, and there is an urgent need to develop new materials showing especially high proton conductivity. Here, we report the ultra-fast proton conduction in a novel metal–organic framework, MFM-808, which adopts an unprecedented topology and a unique structure consisting of two-dimensional layers of {Zr 6 }-clusters. By replacing the bridging formate with sulfate ligands within {Zr 6 }-layers, the modified MFM-808-SO 4 exhibits an exceptional proton conductivity of 0.21 S·cm –1 at 85 °C and 99% relative humidity. Modeling by molecular dynamics confirms that proton transfer is promoted by an efficient two-dimensional conducting network assembled by sulfate–{Zr 6 }-layers. MFM-808-SO 4 also possesses excellent photocatalytic activity for water splitting to produce H 2 , paving a new pathway to achieve a renewable hydrogen-energy cycle.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Modulation of Uptake and Reactivity of Nitrogen Dioxide in Metal-Organic Framework Materials
We report the modulation of reactivity of nitrogen dioxide (NO 2 ) in a charged metal–organic framework (MOF) material, MFM-305-CH 3 in which unbound N-centres are methylated and the cationic charge counter-balanced by Cl - ions in the pores. Uptake of NO 2 into MFM-305-CH 3 leads to reaction between NO 2 and Cl - to give nitrosyl chloride (NOCl) and NO 3 - anions. A high dynamic uptake of 6.58 mmol g -1 at 298 K is observed for MFM-305-CH 3 as measured using a flow of 500 ppm NO 2 in He. In contrast, the analogous neutral material, MFM-305, shows a much lower uptake of 2.38 mmol g -1 . The binding domains and reactivity of adsorbed NO 2 molecules within MFM-305-CH 3 and MFM-305 have been probed using in situ synchrotron X-ray diffraction, inelastic neutron scattering and by electron paramagnetic resonance, high-field solid-state nuclear magnetic resonance and UV/Vis spectroscopies. The design of charged porous sorbents provides a new platform to control the reactivity of corrosive air pollutants.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Synthesis of Nitro Compounds from Nitrogen Dioxide Captured in a Metal-Organic Framework
Increasing levels of air pollution are driving the need for the development of new processes that take “waste-to-chemicals”. Herein, we report the capture and conversion under ambient conditions of a major air pollutant, NO 2 , using a robust metal-organic framework (MOF) material, Zr-bptc (H 4 bptc = 3,3',5,5'-biphenyltetracarboxylic acid), comprising {Zr 6 (μ 3 -O) 4 (μ 3 -OH) 4 (COO) 12 } clusters linked by 4-connected bptc 4– ligands in an ftw topology. At 298 K, Zr-bptc shows exceptional stability and adsorption of NO 2 at both low (4.9 mmol g –1 at 10 mbar) and high pressures (13.8 mmol g –1 at 1.0 bar), as measured by isotherm experiments. Dynamic breakthrough experiments have confirmed the selective retention of NO 2 by Zr-bptc at low concentrations under both dry and wet conditions. The immobilized NO 2 can be readily transformed into valuable nitro compounds relevant to construction, agrochemical, and pharmaceutical industries. In situ crystallographic and spectroscopic studies reveal strong binding interactions of NO 2 to the {Zr 6 (μ 3 -O) 4 (μ 3 -OH) 4 (COO) 12 } cluster node. This study paves a circular pathway to enable the integration of nitrogen-based air pollutants into the production of fine chemicals.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Highly Efficient Proton Conduction in the Metal–Organic Framework Material MFM-300(Cr)·SO 4 (H 3 O) 2
The development of materials showing rapid proton conduction with a low activation energy and stable performance over a wide temperature range is an important and challenging line of research. Here, we report confinement of sulfuric acid within porous MFM-300(Cr) to give MFM-300(Cr)·SO 4 (H 3 O) 2 , which exhibits a record-low activation energy of 0.04 eV, resulting in stable proton conductivity between 25 and 80 °C of >10 –2 S cm –1 . In situ synchrotron X-ray powder diffraction (SXPD), neutron powder diffraction (NPD), quasielastic neutron scattering (QENS), and molecular dynamics (MD) simulation reveal the pathways of proton transport and the molecular mechanism of proton diffusion within the pores. Confined sulfuric acid species together with adsorbed water molecules play a critical role in promoting the proton transfer through this robust network to afford a material in which proton conductivity is almost temperature-independent.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Structural and Dynamic Analysis of Sulphur Dioxide Adsorption in a Series of Zirconium-Based Metal–Organic Frameworks
We report reversible high capacity adsorption of SO 2 in robust Zr-based metal–organic framework (MOF) materials. Zr-bptc (H 4 bptc=biphenyl-3,3',5,5'-tetracarboxylic acid) shows a high SO 2 uptake of 6.2 mmol g -1 at 0.1 bar and 298 K, reflecting excellent capture capability and removal of SO 2 at low concentration (2500 ppm). Dynamic breakthrough experiments confirm that the introduction of amine, atomically-dispersed Cu II or heteroatomic sulphur sites into the pores enhance the capture of SO 2 at low concentrations. The captured SO 2 can be converted quantitatively to a pharmaceutical intermediate, aryl N-aminosulfonamide, thus converting waste to chemical values. In situ X-ray diffraction, infrared micro-spectroscopy and inelastic neutron scattering enable the visualisation of the binding domains of adsorbed SO 2 molecules and host–guest binding dynamics in these materials at the atomic level. Refinement of the pore environment plays a critical role in designing efficient sorbent materials.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Direct Observation of Ammonia Storage in UiO-66 Incorporating Cu(II) Binding Sites
The presence of active sites in metal–organic framework (MOF) materials can control and affect their performance significantly in adsorption and catalysis. However, revealing the interactions between the substrate and active sites in MOFs at atomic precision remains a challenging task. Here, we report the direct observation of binding of NH 3 in a series of UiO-66 materials containing atomically dispersed defects and open Cu(I) and Cu(II) sites. While all MOFs in this series exhibit similar surface areas (1111–1135 m 2 g –1 ), decoration of the -OH site in UiO-66-defect with Cu(II) results in a 43% enhancement of the isothermal uptake of NH 3 at 273 K and 1.0 bar from 11.8 in UiO-66-defect to 16.9 mmol g –1 in UiO-66-Cu II . A 100% enhancement of dynamic adsorption of NH 3 at a concentration level of 630 ppm from 2.07 mmol g –1 in UiO-66-defect to 4.15 mmol g –1 in UiO-66-Cu II at 298 K is observed. In situ neutron powder diffraction, inelastic neutron scattering, and electron paramagnetic resonance, solid-state nuclear magnetic resonance, and infrared spectroscopies, coupled with modeling reveal that the enhanced NH 3 uptake in UiO-66-Cu II originates from a {Cu(II)···NH 3 } interaction, with a reversible change in geometry at Cu(II) from near-linear to trigonal coordination. This work represents the first example of structural elucidation of NH 3 binding in MOFs containing open metal sites and will inform the design of new efficient MOF sorbents by targeted control of active sites for NH 3 capture and storage.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
A {Ni 12 }-Wheel-Based Metal-Organic Framework for Coordinative Binding of Sulphur Dioxide and Nitrogen Dioxide
Air pollution by SO 2 and NO 2 has caused significant risks on the environment and human health. Understanding the mechanism of active sites within capture materials is of fundamental importance to the development of new clean-up technologies. We report the crystallographic observation of reversible coordinative binding of SO 2 and NO 2 on open Ni II sites in a metal-organic framework (NKU-100) incorporating unprecedented {Ni 12 }-wheels; each wheel exhibits six open Ni II sites on desolvation. Immobilised gas molecules are further stabilised by cooperative host-guest interactions comprised of hydrogen bonds, π∙∙∙π interactions and dipole interactions. At 298 K and 1.0 bar, NKU-100 shows adsorption uptakes of 6.21 and 5.80 mmol g -1 for SO 2 and NO 2 , respectively. Dynamic breakthrough experiments have confirmed the selective retention of SO 2 and NO 2 at low concentrations under dry conditions. This work will inspire the future design of efficient sorbents for the capture of SO 2 and NO 2 .
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Purification of Propylene and Ethylene by a Robust Metal–Organic Framework Mediated by Host–Guest Interactions
Industrial purification of propylene and ethylene requires cryogenic distillation and selective hydrogenation over palladium catalysts to remove propane, ethane and/or trace amounts of acetylene. Here, we report the excellent separation of equimolar mixtures of propylene/propane and ethylene/ethane, and of a 1/100 mixture of acetylene/ethylene by a highly robust microporous material, MFM-520, under dynamic conditions. In situ synchrotron single crystal X-ray diffraction, inelastic neutron scattering and analysis of adsorption thermodynamic parameters reveal that a series of synergistic host-guest interactions involving hydrogen bonding and π⋯π stacking interactions underpin the cooperative binding of alkenes within the pore. Notably, the optimal pore geometry of the material enables selective accommodation of acetylene. The practical potential of this porous material has been demonstrated by fabricating mixed-matrix membranes comprising MFM-520, Matrimid and PIM-1, and these exhibit not only a high permeability for propylene (≈1984 Barrer), but also a separation factor of 7.8 for an equimolar mixture of propylene/propane at 298 K.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
High Ammonia Adsorption in MFM-300 Materials: Dynamics and Charge Transfer in Host–Guest Binding
Ammonia (NH 3 ) is a promising energy resource owing to its high hydrogen density. However, its widespread application is restricted by the lack of efficient and corrosion-resistant storage materials. In this work, we report high NH 3 adsorption in a series of robust metal-organic framework (MOF) materials, MFM-300(M) (M = Fe, V, Cr, In). MFM-300(M) (M = Fe, V III , Cr) show fully reversible capacity for >20 cycles, reaching capacities of 16.1, 15.6, and 14.0 mmol g -1 , respectively, at 273 K and 1 bar. Under the same conditions, MFM-300(V IV ) exhibits the highest uptake among this series of MOFs of 17.3 mmol g -1 . In situ neutron powder diffraction, single-crystal X-ray diffraction, and electron paramagnetic resonance spectroscopy confirm that the redox-active V center enables host-guest charge transfer, with V IV being reduced to V III and NH 3 being oxidized to hydrazine (N 2 H 4 ). A combination of in situ inelastic neutron scattering and DFT modeling has revealed the binding dynamics of adsorbed NH 3 within these MOFs to afford a comprehensive insight into the application of MOF materials to the adsorption and conversion of NH 3 .
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Categorization of Computing Education Resources into the ACM Computing Classification System
The Ensemble Portal harvests resources from multiple heterogonous federated collections. Managing these dynamically increasing collections requires an automatic mechanism to categorize records in to corresponding topics. We propose an approach to use existing ACM DL metadata to build classifiers for harvested resources in the Ensemble project. We also present our experience on utilizing the Amazon Mechanical Turk platform to build ground truth training data sets from Ensemble collections.
99 GENERAL AND MISCELLANEOUS↗