Engineering topics

Chen, Zhihua

Publications and source records attributed to Chen, Zhihua.

4 records

DOE OSTI2023

Carbon flowers as electrocatalysts for the reduction of oxygen to hydrogen peroxide

Small-scale and decentralized production of H 2 O 2 via electrochemical reduction of oxygen is of great benefit, especially for sanitization, air and water purification, as well as for a variety of chemical processes. The development of low-cost and high-performance catalysts for this reaction remains a key challenge. Carbon-based materials have drawn substantial research efforts in recent years due to their advantageous properties, such as high chemical stability and high tunability in active sites and morphology. Deeper understanding of structure–activity relationships can guide the design of improved catalysts. We hypothesize that mass transport to active sites is of great importance, and herein we use carbon materials with unique flower-like superstructures to achieve high activity and selectivity for O 2 reduction to H 2 O 2 . The abundance of nitrogen active sites controlled by pyrolysis temperature resulted in high catalytic activity and selectivity for oxygen reduction reaction (ORR). The flower superstructure showed higher performance than the spherical nanoparticles due to greater accessibility to the active sites. Chemical activation improves the catalysts’ performances further, driving the production of H 2 O 2 to a record-setting rate of 816 mmol·g cat -1 ·h -1 using a bulk electrolysis setup. In conclusion, this work demonstrates the development of a highly active catalyst for the sustainable production of H 2 O 2 through rational design and synthetic control. The understanding from this work provides further insight into the design of future carbon-based electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Foundry-compatible high-resolution patterning of vertically phase-separated semiconducting films for ultraflexible organic electronics

Solution processability of polymer semiconductors becomes an unfavorable factor during the fabrication of pixelated films since the underlying layer is vulnerable to subsequent solvent exposure. A foundry-compatible patterning process must meet requirements including high-throughput and high-resolution patternability, broad generality, ambient processability, environmentally benign solvents, and, minimal device performance degradation. However, known methodologies can only meet very few of these requirements. Here, a facile photolithographic approach is demonstrated for foundry-compatible high-resolution patterning of known p- and n-type semiconducting polymers. This process involves crosslinking a vertically phase-separated blend of the semiconducting polymer and a UV photocurable additive, and enables ambient processable photopatterning at resolutions as high as 0.5 μm in only three steps with environmentally benign solvents. The patterned semiconducting films can be integrated into thin-film transistors having excellent transport characteristics, low off-currents, and high thermal (up to 175 °C) and chemical (24 h immersion in chloroform) stability. Moreover, these patterned organic structures can also be integrated on 1.5 μm-thick parylene substrates to yield highly flexible (1 mm radius) and mechanically robust (5,000 bending cycles) thin-film transistors.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Changes in water vapor adsorption and water film thickness in clayey materials as a function of relative humidity

Abstract Soil water, with adsorbed water being an important component, plays an important role in fluid flow and chemical movement in the unsaturated zone. The adsorbed water consists of water film and interlayer water, and its content is related to the relative humidity (RH). This study theoretically and experimentally focuses on the variation in adsorbed water content in clayey materials as the RH changes. Based on a slit‐pore model, three types of water (water film, interlayer water, and capillary water) could be present in the water vapor adsorption process. The variation of water film is obtained from the analysis of interfacial forces, and then the total water content can be quantitatively subdivided into these three types of water for different RH values. The slit‐pore adsorption model was used with experimental measurements (water vapor adsorption and N 2 physisorption) to quantify the amounts and interrelationships of these three different types of water to six clayey materials, namely three clay minerals (kaolinite, montmorillonite, and illite–smectite mixed layer) and three clay‐rich sediments from the Jianghan Plain in China. The main results are that (a) the volumes of water vapor adsorption are much greater than those of N 2 adsorption except for kaolinite; (b) interlayer water largely dominates the growth of total water content in montmorillonite and results in a concentration of 0.090 ml g −1 at 95% RH; and (c) the minimum thickness of water film is calculated to be 0.23 nm, and the maximum value is one‐third of the pore width by considering the interfacial forces.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2020

Two-Dimensional Conductive Ni-HAB as a Catalyst for the Electrochemical Oxygen Reduction Reaction

Catalytic systems whose properties can be systematically tuned via changes in synthesis conditions are highly desirable for the next-generation catalyst design and optimization. Herein, we present a two-dimensional (2D) conductive metal–organic framework consisting of M-N 4 units (M = Ni, Cu) and a hexaaminobenzene (HAB) linker as a catalyst for the oxygen reduction reaction. By varying synthetic conditions, we prepared two Ni-HAB catalysts with different crystallinities, resulting in catalytic systems with different electric conductivities, electrochemical activity, and stability. We show that crystallinity has a positive impact on conductivity and demonstrate that this improved crystallinity/conductivity improves the catalytic performance of our model system. Additionally, density functional theory simulations were performed to probe the origin of M-HAB’s catalytic activity, and they suggest that M-HAB’s organic linker acts as the active site with the role of the metal being to modulate the linker sites’ binding strength.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗