Search NASA⌕ Search

Engineering topics

Cheng, B.

Publications and source records attributed to Cheng, B..

At least 19 records

Bio-inspired gas sensing: boosting performance with sensor optimization guided by “machine learning”

The performance of existing gas sensors often degrades in field conditions because of the loss of measurement accuracy in the presence of interferences. Thus, new sensing approaches are required with improved sensor selectivity. We are developing a new generation of gas sensors, known as multivariable sensors, that have several independent responses for multi-gas detection with a single sensor. In this study, we analyze the capabilities of natural and fabricated photonic three-dimensional (3-D) nanostructures as sensors for the detection of different gaseous species, such as vapors and non-condensable gases. We employed bare Morpho butterfly wing scales to control their gas selectivity with different illumination angles. Next, we chemically functionalized Morpho butterfly wing scales with a fluorinated silane to boost the response of these nanostructures to the vapors of interest and to suppress the response to ambient humidity. Further, we followed our previously developed design rules for sensing nanostructures and fabricated bioinspired inorganic 3-D nanostructures to achieve functionality beyond natural Morpho scales. These fabricated nanostructures have embedded catalytically active gold nanoparticles to operate at high temperatures of ≈300 °C for the detection of gases for solid oxide fuel cell (SOFC) applications. Our performance advances in the detection of multiple gaseous species with specific nanostructure designs were achieved by coupling the spectral responses of these nanostructures with machine learning (a.k.a. multivariate analysis, chemometrics) tools. Our newly acquired knowledge from studies of these natural and fabricated inorganic nanostructures coupled with machine learning data analytics allowed us to advance our design rules for sensing nanostructures toward the required gas selectivity for numerous gas monitoring scenarios at room and high temperatures for industrial, environmental, and other applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of periodically driven systems by x-ray absorption spectroscopy using asynchronous data collection mode

Here, we report the development, testing, and demonstration of a setup for modulation excitation spectroscopy experiments at the Inner Shell Spectroscopy beamline of National Synchrotron Light Source - II. A computer algorithm and dedicated software were developed for asynchronous data processing and analysis. We demonstrate the reconstruction of X-ray absorption spectra for different time points within the modulation pulse using a model system. This setup and the software are intended for a broad range of functional materials which exhibit structural and/or electronic responses to the external stimulation, such as catalysts, energy and battery materials, and electromechanical devices.

36 MATERIALS SCIENCE↗

Mixing with applications to inertial-confinement-fusion implosions

Approximate one-dimensional (1D) as well as 2D and 3D simulations are playing an important supporting role in the design and analysis of future experiments at National Ignition Facility. This work is mainly concerned with 1D simulations, used extensively in design and optimization. We couple a 1D buoyancy-drag mix model for the mixing zone edges with a 1D inertial confinement fusion simulation code. This analysis predicts that National Ignition Campaign (NIC) designs are located close to a performance cliff, so modeling errors, design features (fill tube and tent) and additional, unmodeled instabilities could lead to significant levels of mix. The performance cliff we identify is associated with multimode plastic ablator (CH) mix into the hot-spot deuterium and tritium (DT). The buoyancy-drag mix model is mode number independent and selects implicitly a range of maximum growth modes. Our main conclusion is that single effect instabilities are predicted not to lead to hot-spot mix, while combined mode mixing effects are predicted to affect hot-spot thermodynamics and possibly hot-spot mix. Combined with the stagnation Rayleigh-Taylor instability, we find the potential for mix effects in combination with the ice-to-gas DT boundary, numerical effects of Eulerian species CH concentration diffusion, and ablation-driven instabilities. With the help of a convenient package of plasma transport parameters developed here, we give an approximate determination of these quantities in the regime relevant to the NIC experiments, while ruling out a variety of mix possibilities. Plasma transport parameters affect the 1D buoyancy-drag mix model primarily through its phenomenological drag coefficient as well as the 1D hydro model to which the buoyancy-drag equation is coupled.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of preheat and mix on the fuel adiabat of an imploding capsule

We demonstrate the effect of preheat, hydrodynamic mix and vorticity on the adiabat of the deuterium-tritium (DT) fuel in fusion capsule experiments. We show that the adiabat of the DT fuel increases resulting from hydrodynamic mixing due to the phenomenon of entropy of mixture. An upper limit of mix, M clean =M DT ≥ 0:98 is found necessary to keep the DT fuel on a low adiabat. We demonstrate in this study that the use of a high adiabat for the DT fuel in theoretical analysis and with the aid of 1D code simulations could explain some aspects of 3D effects and mix in capsule implosion. Furthermore, we can infer from our physics model and the observed neutron images the adiabat of the DT fuel in the capsule and the amount of mix produced on the hot spot.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fabrication of rodlets with coated and lined Mo-alloy cladding for testing and irradiation

Molybdenum alloy fuel cladding with an outer protective layer has been proposed to achieve enhanced tolerance to severe loss of coolant accidents for light water reactors. The accident tolerant fuel cladding will need to meet stringent fuel reliability requirements and significantly delay steam reaction during a severe accident to provide plant operators additional coping time to recover from the accident. A laboratory measurable target for this feasibility study with coated Mo cladding is to demonstrate its capability to survive in steam and maintain fuel rods in coolable geometry at 1200-1500 Celsius degrees for at least 24 hours. Preliminary studies indicate such a capability may provide additional coying of 4-19 hours. A feasibility study undertaken since 2012 has demonstrated feasibility of fabricating long, thin-wall Mo and Mo-ODS tubes, and forming a metallurgically bonded protective coating of FeCrAl or Zr-alloy via physical vapor deposition to provide protection of the Mo cladding in 1200 C. degrees for 24 hours. The diametral ductility of the Mo and Mo-ODS thin wall tubes can be increased to 5-15% pre-irradiation to meet fuel operational requirements. Fabrication of the outer protective layer using thermo-mechanical processing, such as hot isostatic pressing and hot coextrusion, has been under evaluation to achieve high quality lined Mo cladding from commercial scale production. Welding of lined Mo tubes to end-caps are being developed using a combination of solid state welding of laser or electron beam seal welding. Rodlets of lined Mo tubes are being fabricated for further testing to validate its reliability under normal operation and capability of accident tolerance to the 1200- 1500 C. degrees range. Test reactor irradiation is also being planned. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Tuning and stabilizing topological insulator Bi{sub 2}Se{sub 3} in the intrinsic regime by charge extraction with organic overlayers

In this work, we use charge extraction via organic overlayer deposition to lower the chemical potential of topological insulator (TI) Bi{sub 2}Se{sub 3} thin films into the intrinsic (bulk-insulating) regime. We demonstrate the tuning and stabilization of intrinsic topological insulators at high mobility with low-cost organic films. With the protection of the organic charge extraction layers tetrafluorotetracyanoquinodimethane or tris(acetylacetonato)cobalt(III) (Co(acac){sub 3}), the sample is stable in the atmosphere with chemical potential ∼135 meV above the Dirac point (85 meV below the conduction band minimum, well within the topological insulator regime) after four months, which is an extraordinary level of environmental stability. The Co complex demonstrates the use of an organometallic for modulating TI charge density. The mobility of surface state electrons is enhanced as high as ∼2000 cm{sup 2}/V s. Even at room temperature, a true topologically insulating state is realized and stabilized for months' exposure to the atmosphere.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Analysis of NIF experiments with the minimal energy implosion model

We apply a recently developed analytical model of implosion and thermonuclear burn to fusion capsule experiments performed at the National Ignition Facility that used low-foot and high-foot laser pulse formats. Our theoretical predictions are consistent with the experimental data. Our studies, together with neutron image analysis, reveal that the adiabats of the cold fuel in both low-foot and high-foot experiments are similar. That is, the cold deuterium-tritium shells in those experiments are all in a high adiabat state at the time of peak implosion velocity. The major difference between low-foot and high-foot capsule experiments is the growth of the shock-induced instabilities developed at the material interfaces which lead to fuel mixing with ablator material. Furthermore, we have compared the NIF capsules performance with the ignition criteria and analyzed the alpha particle heating in the NIF experiments. Our analysis shows that alpha heating was appreciable only in the high-foot experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Sensitivity of inertial confinement fusion hot spot properties to the deuterium-tritium fuel adiabat

We determine the dependence of key Inertial Confinement Fusion (ICF) hot spot simulation properties on the deuterium-tritium fuel adiabat, here modified by addition of energy to the cold shell. Variation of this parameter reduces the simulation to experiment discrepancy in some, but not all, experimentally inferred quantities. Using simulations with radiation drives tuned to match experimental shots N120321 and N120405 from the National Ignition Campaign (NIC), we carry out sets of simulations with varying amounts of added entropy and examine the sensitivities of important experimental quantities. Neutron yields, burn widths, hot spot densities, and pressures follow a trend approaching their experimentally inferred quantities. Ion temperatures and areal densities are sensitive to the adiabat changes, but do not necessarily converge to their experimental quantities with the added entropy. This suggests that a modification to the simulation adiabat is one of, but not the only explanation of the observed simulation to experiment discrepancies. In addition, we use a theoretical model to predict 3D mix and observe a slight trend toward less mixing as the entropy is enhanced. Instantaneous quantities are assessed at the time of maximum neutron production, determined dynamically within each simulation. These trends contribute to ICF science, as an effort to understand the NIC simulation to experiment discrepancy, and in their relation to the high foot experiments, which features a higher adiabat in the experimental design and an improved neutron yield in the experimental results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗