Engineering topics
Cheng, Sichao
Publications and source records attributed to Cheng, Sichao.
Depolymerization of plastics by means of electrified spatiotemporal heating
Not provided.
Direct non-oxidative methane coupling on vitreous silica supported iron catalysts
Direct non-oxidative methane coupling (NMC) is one of the promising pathways for methane upgrading into value-added olefin and aromatic hydrocarbons. The silica-supported iron (i.e., Fe/SiO 2 ) catalyst has been reported effective for NMC, but the effects of silica support on the catalyst property and NMC performance have rarely been explored. Here, in this work, we prepared a vitreous silica-supported iron (Fe/SiO 2 -V) catalyst by flame fusion of a mixture of quartz silica and fayalite. The physicochemical properties and NMC performance of the as-prepared catalysts were measured. Compared to crystalline cristobalite support in Fe/SiO 2 catalyst that has been studied previously, vitreous silica support has disordered Si-O bonds and structural defects, enabling better iron dispersion and more vital metal-support interaction. The as-prepared Fe/SiO 2 -V catalyst had a shorter induction period in methane activation and lower coke yield in NMC. The increase in iron concentration in Fe/SiO 2 -V catalysts elongated the catalyst induction period and promoted aromatics and coke formation. The coke type of the spent Fe/SiO 2 -V catalyst is more uniform than the cristobalite-supported iron catalyst.
Programmable heating and quenching for efficient thermochemical synthesis
Conventional thermochemical syntheses by continuous heating under near-equilibrium conditions face critical challenges in improving the synthesis rate, selectivity, catalyst stability and energy efficiency, owing to the lack of temporal control over the reaction temperature and time, and thus the reaction pathways. As an alternative, we present a non-equilibrium, continuous synthesis technique that uses pulsed heating and quenching (for example, 0.02 s on, 1.08 s off) using a programmable electric current to rapidly switch the reaction between high (for example, up to 2,400 K) and low temperatures. The rapid quenching ensures high selectivity and good catalyst stability, as well as lowers the average temperature to reduce the energy cost. Using CH4 pyrolysis as a model reaction, our programmable heating and quenching technique leads to high selectivity to value-added C2 products (>75% versus <35% by the conventional non-catalytic method and versus <60% by most conventional methods using optimized catalysts). Our technique can be extended to a range of thermochemical reactions, such as NH 3 synthesis, for which we achieve a stable and high synthesis rate of about 6,000 μmol g Fe –1 h –1 at ambient pressure for >100 h using a non-optimized catalyst. Furthermore, this study establishes a new model towards highly efficient non-equilibrium thermochemical synthesis.
Understanding the Impact of Hydrogen Activation by SrCe 0.8 Zr 0.2 O 3-δ Perovskite Membrane Material on Direct Non-Oxidative Methane Conversion
Direct non-oxidative methane conversion (DNMC) converts methane (CH 4 ) in one step to olefin and aromatic hydrocarbons and hydrogen (H 2 ) co-product. Membrane reactors comprising methane activation catalysts and H 2 -permeable membranes can enhance methane conversion by in situ H 2 removal via Le Chatelier's principle. Rigorous description of H 2 kinetic effects on both membrane and catalyst materials in the membrane reactor, however, has been rarely studied. In this work, we report the impact of hydrogen activation by hydrogen-permeable SrCe 0.8 Zr 0.2 O 3-δ (SCZO) perovskite oxide material on DNMC over an iron/silica catalyst. The SCZO oxide has mixed ionic and electronic conductivity and is capable of H 2 activation into protons and electrons for H 2 permeation. In the fixed-bed reactor packed with a mixture of SCZO oxide and iron/silica catalyst, stable and high methane conversion and low coke selectivity in DNMC was achieved by co-feeding of H 2 in methane stream. The characterizations show that SCZO activates H 2 to favor “soft coke” formation on the catalyst. The SCZO could absorb H 2 in situ to lower its local concentration to mitigate the reverse reaction of DNMC in the tested conditions. The co-existence of H 2 co-feed, SCZO oxide, and DNMC catalyst in the present study mimics the conditions of DNMC in the H 2 -permeable SCZO membrane reactor. The findings in this work offer the mechanistic understanding of and guidance for the design of H 2 -permeable membrane reactors for DNMC and other alkane dehydrogenation reactions.
Ethylene production by direct conversion of methane over isolated single active centers
Not provided.
Isolated Metal Sites in Cu–Zn–Y/Beta for Direct and Selective Butene-Rich C 3+ Olefin Formation from Ethanol
Direct and selective production of C 3+ olefins from bioethanol remains a critical challenge and important for the production of renewable transportation fuels such as aviation biofuels. In this study, we report a Cu–Zn–Y/Beta catalyst for selective ethanol conversion to butene-rich C 3+ olefins (88% selectivity at 100% ethanol conversion, 623 K), where the Cu, Zn, and Y sites are all highly dispersed. The ethanol-to-butene reaction network includes ethanol dehydrogenation, aldol condensation to crotonaldehyde, and hydrogenation to butyraldehyde, followed by further hydrogenation and dehydration reactions to form butenes. Cu sites play a critical role in promoting hydrogenation of the crotonaldehyde C═C bond to form butyraldehyde in the presence of hydrogen, making this a distinctive pathway from crotyl alcohol-based ethanol-to-butadiene reaction. Reaction rate measurements in the presence of ethanol and acetaldehyde (543 K, 12 kPa ethanol, 1.2 kPa acetaldehyde, 101.9 kPa H 2 ) over monometallic Zn/Beta and Y/Beta catalysts indicate that Y sites have higher C–C coupling rates than over Zn sites (initial C–C coupling rate, 6.1 × 10 –3 mol mol Y –1 s –1 vs 1.2 × 10 –3 mol mol Zn –1 s –1 ). Further, Lewis-acidic Y-site densities over Cu–Zn–Y/Beta with varied Y loadings are linearly correlated with the initial C–C coupling rates, suggesting that Lewis-acidic Y sites are the predominant sites that catalyze C–C coupling in Cu–Zn–Y/Beta catalysts. Control experiments show that the dealuminated Beta support is important to form higher density of Lewis-acidic Y sites in comparison with other supports such as silica, or deboronated MWW despite similar atomic dispersion of Y sites and Y–O coordination numbers over these supports, leading to more than 9 times higher C–C coupling rate per mole Y over dealuminated Beta relative to other supports. This study highlights the significance of unique combination of metal sites in contributing to the selective valorization of ethanol to C 3+ olefins, motivating for exploring multifunctional zeolite catalysts, where the presence of multiple sites with varying reactivities and functions allows for controlling the predominant molecular fluxes toward the desired products in complex reactions.