Engineering topics
Cheng, Zhe
Publications and source records attributed to Cheng, Zhe.
Ionic Peltier effect in Li-ion electrolytes
The coupled transport of charge and heat provide fundamental insights into the microscopic thermodynamics and kinetics of materials. We describe a sensitive ac differential resistance bridge that enables measurements of the temperature difference on two sides of a coin cell with a resolution of better than 10 μK. We use this temperature difference metrology to determine the ionic Peltier coefficients of symmetric Li-ion electrochemical cells as a function of Li salt concentration, solvent composition, electrode material, and temperature. The Peltier coefficients Π are negative, i.e., heat flows in the direction opposite to the drift of Li ions in the applied electric field, large, –Π > 30 kJ mol –1 , and increase with increasing temperature at T > 300 K. The Peltier coefficient is approximately constant on time scales that span the characteristic time for mass diffusion across the thickness of the electrolyte, suggesting that heat of transport plays a minor role in comparison to the changes in partial molar entropy of Li at the interface between the electrode and electrolyte. Here, our work demonstrates a new platform for studying the non-equilibrium thermodynamics of electrochemical cells and provides a window into the transport properties of electrochemical materials through measurements of temperature differences and heat currents that complement traditional measurements of voltages and charge currents.
Effects of processing conditions on flash sintering of commercial ZrN
Flash sintering (FS) is a potentially rapid and low-cost manufacturing technique for advanced ceramics. There are still many unknowns about ceramic FS, especially for highly conductive high-temperature ceramics (HTC), which often display decreased bulk conductivity with increasing temperature. This study qualitatively characterizes the flash behavior of highly conductive HTC materials using zirconium nitride (ZrN) as an example. The effects of processing parameters (e.g., DC voltage/electrical field strength, voltage ramp rate, post-flash holding time, mechanical pressure, sample milling, and choice of electrode materials) on ZrN flash behavior are also qualitatively studied and linked to samples microstructure and hardness. It is observed that best densification was achieved using 5 min Spex-milled ZrN powder under 25 MPa of applied pressure and constant 8 V DC. The potential mechanism for ZrN FS and the similarity and difference from FS of conventional oxides like YSZ have been proposed based on experimental observations, and the directions for future research are also pointed out.
Reactive flash sintering of TiZrN and TiAlN ternary metal nitrides
Here, this study demonstrated the reactive flash sintering (RFS) for two powder mixtures: TiN-ZrN (both conducting) and AlN-TiN (TiN conducting but AlN insulating), targeting ternary metal nitrides (TMN) of Ti 0.5 Zr 0.5 N and Ti 0.5 Al 0.5 N, respectively. A constant volage and pressure (e.g., 8 V DC, ∼15 MPa) at room temperature triggered the flash (current density up to 27 A/mm 2 ) without pre-heating, and the entire RFS process finished in a few minutes. For TiZrN, the flash was instantaneous whereas for TiAlN, there was a long incubation before the flash followed by a quick and dramatic flash. Both conventional ex situ XRD and in situ synchrotron study had been carried out. They showed a uniform Ti 0.57 Zr 0.43 N solution formed in RFS and persisted upon cooling, while (Ti, Al) N solid solution formed at high temperature was not stable and likely went through a very quick phase separation in the cooling process. The final products from RFS had been characterized using SEM/EDS for microstructure. Both TiZrN and TiAlN were dense. Distribution of Ti, Zr, and N was uniform for TiZrN; for TiAlN, Ti and N distribution was uniform, while association of Al with oxygen was observed. TGA-DSC revealed the onset oxidation temperature for TiZrN was comparable to TiN and ZrN, while it was higher by ∼200 °C for TiAlN, likely due to the formation of Al 2 O 3 . In terms of mechanical properties such as hardness or fracture toughness, forming a single-phase solid solution (like TiZrN) does not offer obvious benefits. while large grain size from RFS seemed to be unfavorable. Future optimization of RFS condition and in-depth study by both experiments and simulation are needed to fully understand the composition-processing-structure-property relationships for such TMN from the reactive flash sintering process.
Bioadhesive polymer semiconductors and transistors for intimate biointerfaces
The use of bioelectronic devices relies on direct contact with soft biotissues. For transistor-type bioelectronic devices, the semiconductors that need to have direct interfacing with biotissues for effective signal transduction do not adhere well with wet tissues, thereby limiting the stability and conformability at the interface. Here we report a bioadhesive polymer semiconductor through a double-network structure formed by a bioadhesive brush polymer and a redox-active semiconducting polymer. The resulting semiconducting film can form rapid and strong adhesion with wet tissue surfaces together with high charge-carrier mobility of ~1 square centimeter per volt per second, high stretchability, and good biocompatibility. Further fabrication of a fully bioadhesive transistor sensor enabled us to produce high-quality and stable electrophysiological recordings on an isolated rat heart and in vivo rat muscles.
Achieving tissue-level softness on stretchable electronics through a generalizable soft interlayer design
Soft and stretchable electronics have emerged as highly promising tools for biomedical diagnosis and biological studies, as they interface intimately with the human body and other biological systems. Most stretchable electronic materials and devices, however, still have Young’s moduli orders of magnitude higher than soft bio-tissues, which limit their conformability and long-term biocompatibility. Here, we present a design strategy of soft interlayer for allowing the use of existing stretchable materials of relatively high moduli to versatilely realize stretchable devices with ultralow tissue-level moduli. We have demonstrated stretchable transistor arrays and active-matrix circuits with moduli below 10 kPa—over two orders of magnitude lower than the current state of the art. Benefiting from the increased conformability to irregular and dynamic surfaces, the ultrasoft device created with the soft interlayer design realizes electrophysiological recording on an isolated heart with high adaptability, spatial stability, and minimal influence on ventricle pressure. In vivo biocompatibility tests also demonstrate the benefit of suppressing foreign-body responses for long-term implantation. With its general applicability to diverse materials and devices, this soft-interlayer design overcomes the material-level limitation for imparting tissue-level softness to a variety of bioelectronic devices.
A Critical Review of Thermal Boundary Conductance across Wide and Ultrawide Bandgap Semiconductor Interfaces
Not provided.
High thermal conductivity in wafer-scale cubic silicon carbide crystals
High thermal conductivity electronic materials are critical components for high-performance electronic and photonic devices as both active functional materials and thermal management materials. We report an isotropic high thermal conductivity exceeding 500 W m –1 K –1 at room temperature in high-quality wafer-scale cubic silicon carbide (3C-SiC) crystals, which is the second highest among large crystals (only surpassed by diamond). Furthermore, the corresponding 3C-SiC thin films are found to have record-high in-plane and cross-plane thermal conductivity, even higher than diamond thin films with equivalent thicknesses. Our results resolve a long-standing puzzle that the literature values of thermal conductivity for 3C-SiC are lower than the structurally more complex 6H-SiC. We show that the observed high thermal conductivity in this work arises from the high purity and high crystal quality of 3C-SiC crystals which avoids the exceptionally strong defect-phonon scatterings. Moreover, 3C-SiC is a SiC polytype which can be epitaxially grown on Si. We show that the measured 3C-SiC-Si thermal boundary conductance is among the highest for semiconductor interfaces. These findings provide insights for fundamental phonon transport mechanisms, and suggest that 3C-SiC is an excellent wide-bandgap semiconductor for applications of next-generation power electronics as both active components and substrates.
Electrical, thermal, and H 2 O and CO 2 poisoning behaviors of PrNi 0.5 Co 0.5 O 3-δ electrode for intermediate temperature protonic ceramic electrochemical cells
PrNi 0.5 Co 0.5 O 3-δ (PNC) exhibits adequate total electrical conductivity (~300 S/cm at 400–600 °C) and moisture has no significant effect on it. The thermal expansion coefficient of PNC is 17.6 × 10 –6 /K by dilatometry and 18.43 × 10 –6 /K by in situ XRD. PNC also demonstrates chemical stability against H 2 O and CO 2 . However, PNC symmetrical cell over proton-conducting BaZr 0.4 Ce 0.4 Y 0.1 Yb 0.1 O 3-δ (BZCYYb4411) electrolyte shows significant H 2 O and CO 2 poisoning when those are introduced into O 2 –N 2 mixture. In comparison, symmetrical cells with PNC electrode over the oxygen ion conducting Ce 0.9 Gd 0.1 O 2-δ (GDC) electrolyte show no H 2 O and CO 2 poisoning under similar conditions. Here, it is hypothesized that poisoning from H 2 O and CO 2 of the PNC proton conducting symmetrical cell is caused by their adsorption on the BZCYYb4411 electrolyte instead of PNC electrode. Such a hypothesis is supported by the H 2 O and CO 2 adsorption behaviors on PNC and BZCYYb4411 powder surfaces, as measured by temperature programmed desorption (TPD).
Experimental observation of localized interfacial phonon modes
Interfaces impede heat flow in micro/nanostructured systems. Conventional theories for interfacial thermal transport were derived based on bulk phonon properties of the materials making up the interface without explicitly considering the atomistic interfacial details, which are found critical to correctly describing thermal boundary conductance. Recent theoretical studies predicted the existence of localized phonon modes at the interface which can play an important role in understanding interfacial thermal transport. However, experimental validation is still lacking. Through a combination of Raman spectroscopy and high-energy-resolution electron energy-loss spectroscopy in a scanning transmission electron microscope, we report the experimental observation of localized interfacial phonon modes at ~12 THz at a high-quality epitaxial Si-Ge interface. These modes are further confirmed using molecular dynamics simulations with a high-fidelity neural network interatomic potential, which also yield thermal boundary conductance agreeing well with that measured in time-domain thermoreflectance experiments. Simulations find that the interfacial phonon modes have an obvious contribution to the total thermal boundary conductance. Our findings significantly contribute to the understanding of interfacial thermal transport physics and have impact on engineering thermal boundary conductance at interfaces in applications such as electronics thermal management and thermoelectric energy conversion.
Synthesis and flash sintering of (Hf 1-x Zr x )B 2 solid solution powders
(Hf 1-x Zr x )B 2 solid solution powders were synthesized by two methods. First, solution-based processing of HfCl 4 , ZrCl 4 , sucrose, and H 3 BO 3 was conducted followed by heat treatment in Argon to carry out the carbothermal reduction (CTR) reaction to form the diboride powders. Alternatively, in the so-called borohydride reduction (BHR) method, HfCl 4 , ZrCl 4 and NaBH 4 were mixed in an Argon glove box followed by heat treatment in Argon at 700-1500°C. The synthesized powders were characterized by XRD, SEM, TEM, EDS, and TGA, and the influence of different parameters such as starting composition, heat treatment temperature and time on products characteristics were revealed. Both CTR and BHR solid solution powders were then consolidated within ~5 min in a homemade flash sintering (FS) setup. Here, the composition, microstructure, hardness, and thermal-oxidation properties of flash sintered ceramics were characterized, and the implication of this study and directions for future research were discussed.
Novel High Temperature Carbide and Boride Ceramics for Direct Power Extraction Electrode Applications. Final report
The current project aims to develop new carbide and boride ceramic materials that incorporate different metal elements (e.g., (Hf 1-x Zr x )B 2 , also called ceramic solid solutions) and understand the fundamental composition-processing-structure-property relationships for such materials. Specifically, nano powders and related nano-composites for selected mixed metal carbide and boride materials are synthesized from nano-scale mixed precursors obtained from solution-based processing via heat treatment in inert atmosphere. The obtained fine powders were then consolidated into dense ceramics via a novel flash sintering process. The mechanical properties and thermal oxidation resistance for the obtained materials were evaluated for these materials. It was found that different synthesis routes produced powders with somewhat different characteristics in terms of composition and microstructure, which then led to different properties for the final ceramics. The synthesis and processing methods demonstrated in this study might be adopted for developing other similar high temperature ceramics, while the mixed metal or solid solution ceramic materials obtained from this study might be used as hot electrodes for direction power extraction and other energy-related applications.
Synthesis and Flash Sintering of (Hf1-xZrx)B2 Solid Solution Fine Powders
Fine powders of (Hf1-xZrx)B2 solid solution were synthesized by two methods. In the first one, solution-based processing of HfCl4, ZrCl4, sucrose and H3BO3 was carried out followed by heat treatment (e.g., at 1500 °C for 1 h) in Argon to achieve the carbothermal reduction (CTR) reaction to form the boride solid solution. In the second one, called boron hydride reduction (BHR) method, HfCl4, ZrCl4 and NaBH4 were directly mixed in a glove box followed by heat treatment in Argon at elevated temperatures from 700 to 1500 °C. In addition, the powders synthesized via both methods were flash sintered without sample preheating in a homemade setup. The synthesized powders as well as the flash sintered bulk ceramics were characterized using different techniques including XRD, SEM, EDS, TEM, TGA-DSC, and Vickers hardness test to reveal the inter-relationships between starting materials composition, processing conditions, and the resulting materials microstructure and physical/chemical properties.
Tunable Thermal Energy Transport across Diamond Membranes and Diamond–Si Interfaces by Nanoscale Graphoepitaxy
The development of electronic devices, especially those that involve heterogeneous integration of materials, has led to increased challenges in addressing their thermal operational temperature demands. The heat flow in these systems is significantly influenced or even dominated by thermal boundary resistance at the interface between dissimilar materials. However, controlling and tuning heat transport across an interface and in the adjacent materials has so far drawn limited attention. In this work, we grow chemical vapor-deposited diamond on silicon substrates by graphoepitaxy and experimentally demonstrate tunable thermal transport across diamond membranes and diamond–silicon interfaces. We observed the highest diamond–silicon thermal boundary conductance (TBC) measured to date and increased diamond thermal conductivity due to strong grain texturing in the diamond near the interface. Additionally, nonequilibrium molecular dynamics simulations and a Landauer approach are used to understand the diamond–silicon TBC. Further, these findings pave the way for tuning or increasing thermal conductance in heterogeneously integrated electronics that involve polycrystalline materials and will impact applications including electronics thermal management and diamond growth.
Diffuson-driven ultralow thermal conductivity in amorphous N b 2 O 5 thin films
Niobium pentoxide (Nb 2 O 5 ) has been extensively reported for applications of electrochemical energy storage, memristors, solar cells, light emitting diodes (LEDs), and electrochromic devices. The thermal properties of Nb 2 O 5 play a critical role in device performance of these applications. However, very few studies on the thermal properties of Nb 2 O 5 have been reported and a fundamental understanding of heat transport in Nb 2 O 5 is still lacking. The present work closes this gap and provides the first study of thermal conductivity of amorphous Nb 2 O 5 thin films. Ultralow thermal conductivity is observed without any size effect in films as thin as 48 nm, which indicates that propagons contribute negligibly to the thermal conductivity and that the thermal transport is dominated by diffusons. Density-function-theory (DFT) simulations combined with a diffuson-mediated minimum-thermal-conductivity model confirms this finding. Additionally, the measured thermal conductivity is lower than the amorphous limit (Cahill model), which proves that the diffuson model works better than the Cahill model to describe the thermal conduction mechanism in the amorphous Nb 2 O 5 thin films. Additionally, the thermal conductivity does not change significantly with oxygen vacancy concentration. This stable and low thermal conductivity facilitates excellent performance for applications such as memristors.
Method of the out-of-band rejection improvement of the AlN based surface acoustic wave filters
Not Available