Search NASA⌕ Search

Engineering topics

Chesser, Phillip C.

Publications and source records attributed to Chesser, Phillip C..

At least 19 records

3D printed features on nuclear fuel cladding for optimized heat transfer

A nuclear fuel cladding with improved thermomechanical properties is provided. The nuclear fuel cladding includes a double-walled construction having inner and outer hexagonal sidewalls. The inner sidewall and the outer sidewall are spaced apart from each other to form a cooling channel therebetween, and the inner sidewall surrounds a nuclear fuel and is spaced apart from the nuclear fuel by a small gap. Helical fins extend into the cooling channel to interconnect the inner sidewall and the outer sidewall. Resilient fingers extend toward the nuclear fuel through the small gap to comply with variations in the size of the nuclear fuel due to fabrication tolerances as well as thermal expansion and swelling of the nuclear fuel, for example UO 2 , when undergoing fission. The nuclear fuel cladding is formed according to an additive manufacturing process, for example laser powder bed fusion printing.

Petrie, Christian M.↗

Continuous toolpaths for additive manufacturing

Toolpath generation for additive manufacturing systems involves operations on polygonal contours derived from a model for additively manufacturing a structure. One aspect involves modifying or creating a model to allow parts to be printed without starting and stopping the printing equipment by generating continuous toolpaths or toolpaths having a reduced number of isolated paths. Another aspect involves modifying a slicing engine to generate a continuous toolpath or toolpath having a reduced number of isolated paths based on a representation of an object to be additively manufactured. Another aspect involves selectively placing the gaps at alternating positions among the sliced layers to create a zippering effect.

Borish, Michael C.↗

System and method for additive manufacturing with toolpath bridges and resultant structure

A system and method for improving additive manufacturing, including additive manufacturing toolpaths, is provided. The system and method includes a toolpath generator that obtains initial toolpaths of an object, identifies isolated paths in the toolpaths, and adds bridge connections between neighboring isolated paths in each layer to improve the toolpaths. The bridge connections facilitate the continuous and non-stop deposition of each layer according to improved toolpaths during additive manufacture, which can reduce total deposition time and improve the resultant additive manufacture.

Kim, Seokpum↗

Cable-driven additive manufacturing system

A cable-driven additive manufacturing system includes an end effector configured for linear translation within a three-dimensional workspace, an aerial hoist suspending the end effector by at least one suspension cable, a plurality of base stations disposed below the aerial hoist, and control cables running from each of the base stations to the end effector.

Post, Brian K.↗

Conceptual Design of the Transformational Challenge Reactor

The Transformational Challenge Reactor is a 3-MW(thermal) helium-cooled experimental nuclear reactor designed using an additive manufacturing–informed agile design process. This design process leverages rapid prototyping and advanced materials from emerging additive manufacturing technologies, key characteristics that enable rapid design maturation. The resulting core design incorporates a blend of advanced reactor technologies into an intermediate-spectrum microreactor, including conventionally manufactured tristructural isotropic (TRISO) fuel particles in an advanced manufactured SiC fuel element and a solid yttrium hydride moderator encapsulated in steel. Matured during the design effort, these technologies are incorporated with additively manufactured steel support and fluidic structures to form a 75-cm-outer-diameter cylindrical active core region. Below and above the active core region are axial SiC reflectors, which are housed inside the reactor pressure vessel. The reactor is controlled with an annular shroud actuated external to the pressure vessel in the gap between the pressure vessel and a steel radial reflector. A safety rod is at the center of the core to shut down the reactor when necessary. Helium pressurized at 5 MPa is forced into the pressure vessel below the core and around the core to the top plenum before it is forced down through the axial reflectors and the active core region. The primary pressurized helium loop is operated up to 500°C and includes the pressure vessel, the circulator, and the hot side of a helium-to-air heat exchanger. The secondary loop rejects all heat from the primary loop to ambient air through a heat exchanger. A vented temporary confinement building contains the entire primary loop, with penetrations for a stack, cooling, and the secondary ambient air loop. Finally, this is the first advanced nuclear microreactor designed using additive manufacturing technologies, demonstrating their applicability in an accelerated advanced design process.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Polymer exhaust for eliminating extruder transients

An additive manufacturing method that includes an extruder providing a supply of working material and a nozzle connected with respect to the extruder, the nozzle directing the working material to a deposit surface. A diverter valve is positioned between the extruder and the nozzle to direct the working material to an exhaust port away from the deposit surface under certain conditions.

Chesser, Phillip C.↗

Utility of Big Area Additive Manufacturing for Part Production for Low-Head Hydropower (CRADA NFE-18-07280 Final Report)

ORNL worked with Cadens, LLC, to explore the use of additive manufacturing (AM) to produce low-cost parts for low-head hydropower systems. Cadens develops design optimization software that leverages the flexible, low-cost, high-strength benefits of AM and composite materials. Cadens also operates a micro-hydro lab to test AM components in controlled environments. Until now, Cadens’ tests have been limited to components of a size that they can cost-effectively manufacture using local commercial systems. This project provided an opportunity for Cadens to scale up their modular AM hydropower parts using the capabilities of Big Area Additive Manufacturing (BAAM). This project was a success and resulted in the design and fabrication of several end-use parts of a hydropower system, using a Big Area Additive Manufacturing (BAAM) system. The fabricated parts include a draft tube, thimble, runner housing mold, PVC end fitting and two PVC pipe supports. In addition, a runner system was fabricated using fused deposition modeling on a 3D Platform Workbench 400 Series System.

13 HYDRO ENERGY↗

Method for generating and dispensing a powdered release agent

A method for generating and dispensing a powdered release agent during an additive manufacturing build is disclosed. A solid body of release agent material is ground insitu by a grinder and dispensed on a surface of the part to prevent adhesion of an adjacent layer of a base material. With the addition of the powdered release agent, a support structure is easily separated from the base material when the part is complete, saving time and preventing the part from sustaining unintentional damage. Since no powdered release agent is actually loaded or stored in the apparatus, the potential for spillage, waste, inconsistent dispensing, inadvertent dispensing, and clumping due to humidity is eliminated.

42 ENGINEERING↗

Electromagnetic print nozzle for direct-write additive manufacturing

A method and apparatus for additive manufacturing that includes a material guide for directing a supply of working material and a plurality of rollers for advancing the working material. An electromagnetic heater is provided to heat and deposit molten working material as a new supply of working material is forced through the material guide.

36 MATERIALS SCIENCE↗

Real-Time Defect Correction in Large-Scale Polymer Additive Manufacturing via Thermal Imaging and Laser Profilometer

Defects can result in a failed part and are costly in terms of time and material. This cost is even greater in the context of large-scale additive manufacturing where the objects can be very large. As a result, a great deal of research has focused on defect identification and mitigation. To address defects during object construction, researchers at Oak Ridge National Laboratory’s Manufacturing Demonstration Facility investigated an in-situ control system comprised of two sensors: a thermal camera and laser profilometer. This control system adjusted material flow and build speed to mitigate three types of defects: low layer times, underfill, and overfill. Several test objects were constructed. The control system was found to adjust build parameters to handle low layer times of approximately 15 seconds and height deviations from -100% underfill (the absence of a layer) to 50% overfill. Within two layers, height deviations could be returned to within 10% of the expected layer height. Further, preliminary results suggest the system can compensate for uneven build surfaces.

Borish, Michael↗

Large-Scale Additive Manufacturing for Low Cost Small-Scale Wind Turbine Manufacturing (CRADA NFE-18-07065)

Oak Ridge National Laboratory’s (ORNL) Manufacturing Demonstration Facility (MDF) worked with XZERES Wind to fabricate small (in comparison to traditional wind energy systems) wind turbine blades using large-scale polymer additive manufacturing (AM) in Phase 1 of this project. The results of Phase 1 showed promise for the use of AM in the production of small wind energy systems. Although, the large-scale polymer AM systems available for this project proved to be too large for this application, ORNL and XZERES Wind were able to prove that AM is a viable opportunity to improve small wind turbine blades. The goal for Phase 2 was for XZERES to design tooling for their existing blade geometry and for ORNL to manufacture the tooling and a blade section using advanced manufacturing techniques. Unfortunately, due to personnel turnover at XZERES, Phase 2 was not completed.

17 WIND ENERGY↗

Big Area Additive Manufacturing Engineering Development, Process Trials, and Composite Core Fabrication (CRADA NFE-17-06827 Final Report)

Oak Ridge National Laboratory (ORNL) has worked with Raytheon to develop and test the materials necessary to produce a moderately sized boat using Big Area Additive Manufacturing (BAAM). This Phase 2 project focused on printing and testing the components of the boat designed by Raytheon. This involved collaborating on boat design, printing the boat, testing surface coatings, and assembling the boat.

36 MATERIALS SCIENCE↗

Feasibility of Using BAAM for Mold Inserts for the Precast Concrete Industry (CRADA NFE-17-06874 Final Report)

Oak Ridge National Laboratory worked with Gate Precast to demonstrate the viability of using carbon fiber reinforced acrylonitrile butadiene styrene (ABS) plastic and the Big Area Additive Manufacturing (BAAM) technology to rapidly manufacture molds for the precast concrete industry. This Phase 2 project focused on developing more complex molds that will be used in production.

42 ENGINEERING↗

In-Situ Thermal Imaging for Single Layer Build Time Alteration in Large-Scale Polymer Additive Manufacturing

Ideally, objects are constructed as quickly as possible; however, short build times for a layer can present an issue. Short layer build times do not provide enough time for the material to cool sufficiently. As a result, an object cannot support its own weight nor deal with overhanging features. Additionally, the generation of support structures may be impractical either due to geometry or, in the case of large-scale polymer additive manufacturing, due to being difficult to remove. To address these issues, researchers at Oak Ridge National Laboratory’s Manufacturing Demonstration Facility investigated the use of a thermal camera mounted to a gantry to collect data on an object under construction. This data provided feedback for an in-situ control system to adjust layer build times. Adjustments were made in the form of additional waiting to allow the material to cool to specific thermal thresholds. This additional cooling time allowed the construction of objects with low layer build times or overhanging features that would have otherwise failed.

Borish, Michael↗

Evaluation of Strangpresse Extruder on ORNL BAAM

Researchers at ORNL’s Manufacturing Demonstration Facility (MDF) worked with Strangpresse, LLC to demonstrate Strangpresse’s newly developed extrusion system. The project tested both a small and large Strangpresse extruder. The project also resulted in Strangpresse exclusively licensing ORNL’s some of previously developed extruder technology for high-volume additive manufacturing. The Strangpresse extruder is still under development and testing, however. The next phase of this project could include tasks such as identifying process parameters, making test articles, and quantifying material properties.

42 ENGINEERING↗

Defect Identification and Mitigation Via Visual Inspection in Large-Scale Additive Manufacturing

Defect identification and mitigation is an important avenue of research to improve the overall quality of objects created using additive manufacturing (AM) technologies. Identifying and mitigating defects takes on additional importance in large-scale, industrial AM. In large-scale AM, defects that result in failed prints are extremely costly in terms of time spent and material used. To address these issues, researchers at Oak Ridge National Laboratory’s Manufacturing Demonstration Facility investigated the use of a laser profilometer and thermal camera to collect data concerning an object as it was constructed. These data provided feedback for an in situ control system to adjust object construction. Adjustments were made in the form of automated height control. This paper presents results for both a polymer- and metal-based system. Object construction for both systems was improved significantly, and the resulting objects were more geometrically identical to the ideal 3D representation.

42 ENGINEERING↗

Designing for Big Area Additive Manufacturing

Additive manufacturing (AM), more commonly referred to as 3D printing, is revolutionizing the manufacturing industry. With any new technology comes new rules and guidelines for the optimal use of said technology. Big Area Additive Manufacturing (BAAM), developed by Cincinnati Incorporated and Oak Ridge National Laboratory’s Manufacturing Demonstration Facility, requires a host of new design parameters compared to small-scale 3D printing to create large-scale parts. However, BAAM also creates new possibilities in material testing and various applications in the manufacturing industry. Most of the design constraints of small-scale polymer 3D printers still apply to BAAM. Beyond those constraints, new rules and limitations exist because BAAM’s large-scale system significantly changes the thermal properties associated with small-scale AM. Here, this work details both physical and software-related design considerations for additive manufacturing. After reading this guide, one will have a better understanding of slicing software’s capabilities and limitations, different physical characteristics of design and how to apply them appropriately for AM, and how to take the inherent nature of AM into consideration during the design process.

36 MATERIALS SCIENCE↗

Apparatus for generating and dispensing a powdered release agent

An apparatus 20 and a method 100 for generating and dispensing a powdered 60 release agent during an additive manufacturing build is disclosed. A solid body 28 of release agent material is ground insitu by a grinder 50 and dispensed on a surface of the part 72 to prevent adhesion of an adjacent layer of a base material 70. With the addition of the powdered 60 release agent, a support structure 76 is easily separated from the base material 70 when the part 72 is complete, saving time and preventing the part 72 from sustaining unintentional damage. Since no powdered 60 release agent is actually loaded or stored in the apparatus 20, the potential for spillage, waste, inconsistent dispensing, inadvertent dispensing, and clumping due to humidity is eliminated.

36 MATERIALS SCIENCE↗