Engineering topics

Chetan, Mayank

Publications and source records attributed to Chetan, Mayank.

13 records

DOE OSTI2024

Wind Turbine Aeroelastic Stability in OpenFAST

Wind turbines are growing in size and increasingly suffer from aeroelastic instabilities. Unfortunately, numerical models often show inconsistent results during verification studies. We address this gap by first introducing novel linearization capabilities within the open-source aero-hydro-servo-elastic framework OpenFAST. Next, a code-to-code benchmark study is presented that compares modal parameters between OpenFAST and HAWCStab2 for a land-based version of the International Energy Agency 15-MW reference wind turbine modeled with quasi-steady aerodynamics. The two solvers are in strong agreement except for discrepancies in the second rotor flapwise modes. The differences are attributed to the torsional flexibility of the tower, which is assumed torsionally stiff in the OpenFAST model. Work is ongoing to close this modeling gap. The aeroelastic stability of a low-specific-power land-based wind turbine is also investigated. The impact of design choices is discussed, high-lighting how narrow the margins are between a stable design and an unstable design.

17 WIND ENERGY↗

DOE OSTI2024

Edgewise Structural Damping of a 2.8-MW Land-Based Wind Turbine Rotor Blade

Modern wind turbines push the predictive capabilities of state-of-the-art aero-servo-elastic tools. The existing limitations hide across the numerical tool chain and can result in serious issues, such as missing aeroelastic instabilities during the design phase. Structural damping is an input that is usually hard to estimate, but also has a major impact on the turbine behavior. In this paper, we discuss an experiment that aims to accurately quantify the structural damping characterizing the edgewise modes of modern wind turbine blades. The experiment is carried out on a 2.8-MW land-based wind turbine and features a fast yaw actuation that induces an edgewise motion on one of the three blades. The Covariant-subspace system identification (Cov-SSI) method is then used to post-process the blade root moment to estimate the short-term edgewise structural damping. Despite limitations of the Cov-SSI method, which consistently under-predicts the absolute values of damping, we observe that structural damping decreases across the first three blade edgewise modes, which is different from the stiffness-proportional damping model that assumes that structural damping increases with the modes. This paper argues that a stiffness-proportional damping model, which is implemented in most aeroelastic tools, is therefore not conservative and might hide aeroelastic instabilities that can instead appear in the field.

17 WIND ENERGY↗

DOE OSTI2023

Assessment of Offshore Wind Energy Opportunities and Challenges in the U.S. Gulf of Mexico

This report identifies and discusses opportunities and challenges for offshore wind energy development in the Gulf of Mexico (GOM). The results indicate that offshore wind energy has the potential to be a viable clean energy option to help the region meet the U.S. goals to achieve carbon neutrality by 2050. Many technical challenges are discussed but most can be resolved with engineering solutions that are available to the industry.

17 WIND ENERGY↗

DOE OSTI2022

Design space exploration and decision‐making for a segmented ultralight morphing 50‐MW wind turbine

Abstract Wind turbine design encompasses many different aspects including aerodynamic, structural, electrical, and control system design. To achieve optimal plant performance, a system design approach is utilized in which the performance of the whole wind turbine is evaluated and quantified during operational scenarios with subsystem interactions. In this paper, the design for a Segmented Ultralight Morphing Rotor (SUMR) 50‐MW wind turbine is presented utilizing levelized cost of energy (LCOE) for design choices, with additional quantification of simulated performance shortcomings at the 50‐MW scale. The multi‐disciplinary design process results in a final ultra‐scale turbine configuration that outperforms other existing offshore wind farms regarding the LCOE.

Kianbakht, Sepideh↗

DOE OSTI2022

Field tests of a highly flexible downwind ultralight rotor to mimic a 13-MW turbine rotor

Offshore extreme-scale turbines of 20–25 MW in size may offer reduced energy costs. The technical barriers at these extreme scales include escalating blade masses with increased flexibility as well as high gravity loads and tower-strike issues. These barriers may be addressed with a load-aligning downwind turbine. To investigate this type of design, a field test campaign was conducted with an aeroelastically scaled rotor, termed the Segmented Ultralight Morphing Rotor Demonstrator (SUMR-D). The tests were conducted on the Controls Advanced Research Turbine at the National Renewable Energy Laboratory. The paper gives an overview of the experimental diagnostics, blade design, and results of the field campaign, as well as makes conclusions and recommendations regarding extreme-scale highly flexible downwind rotors.

17 WIND ENERGY↗

DOE OSTI2022

Design and analysis of a segmented blade for a 50 MW wind turbine rotor

Extreme-size wind turbines face logistical challenges due to their sheer size. A solution, segmentation, is examined for an extreme-scale 50 MW wind turbine with 250 m blades using a systematic approach. Segmentation poses challenges regarding minimizing joint mass, transferring loads between segments and logistics. We investigate the feasibility of segmenting a 250 m blade by developing design methods and analyzing the impact of segmentation on the blade mass and blade frequencies. This investigation considers various variables such as joint types (bolted and bonded), adhesive materials, joint locations, number of joints and taper ratios (ply dropping). Segmentation increases blade mass by 4.1%–62% with bolted joints and by 0.4%–3.6% with bonded joints for taper ratios up to 1:10. Cases with large mass growth significantly reduce blade frequencies potentially challenging the control design. We show that segmentation of an extreme-scale blade is possible but mass reduction is necessary to improve its feasibility.

Escalera Mendoza, Alejandra S.↗

DOE OSTI2021

Design of a 3.4-MW wind turbine with integrated plasma actuator-based load control

Historically, cost reduction in wind energy has been accomplished by increasing hub heights and rotor diameters to capture more energy per turbine. The growth in rotor and turbine costs with increasing turbine sizes is also driven by the additional structure that must be added to withstand unsteady aerodynamic loads caused by turbulence, gusts, wind shear, misaligned yaw, upwind wakes, and the tower shadow. In this paper, we present a holistic design solution to integrate active load control using a controllable Gurney flap based on plasma actuators. We illustrate the design solution for a land-based 3.4-MW wind turbine rotor. Comparisons to a baseline reference 3.4-MW wind turbine show significant load reduction (15–18% DEL reduction for flap-wise blade root moments), rotor mass reduction (5–8%), and LCOE reduction (1.16–3.11%). To achieve these results, a comprehensive sequential-iterative design procedure is introduced to integrate the controllable Gurney flap into the turbine design and to drive the design solution toward the best LCOE reduction solution. Results are presented for mapping fatigue load reductions into cost reductions. In addition, an evaluation of active load control extended from Region-III to also include Region-II showed a further 34% reduction in DEL.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2021

Aero-structural design and optimization of 50 MW wind turbine with over 250-m blades

The quest for reduced levelized cost of energy has driven significant growth in wind turbine size; however, larger rotors face significant technical and logistical challenges. The largest published rotor design is 25 MW, and here we consider an even larger 50 MW design with blade length over 250 m. This paper shows that a 50 MW design is indeed possible from a detailed engineering perspective and presents a series of aero-structural blade designs, and critical assessment of technology pathways and challenges for extreme-scale rotors. The 50 MW rotor design begins with Monte Carlo simulations focused on optimizing carbon spar cap and root design. A baseline design resulted in a 250-m blade with mass of 502 tonnes. Subsequently, an aero-structural design and optimization were performed to reduce the blade mass/cost with more than 25% mass reduction and 30% cost reduction by determining optimal blade chord and airfoil thickness for best aero-structural performance.

Yao, Shulong↗

DOE OSTI2021

Multi‐fidelity digital twin structural model for a sub‐scale downwind wind turbine rotor blade

Abstract This paper presents the development of a multi‐fidelity digital twin structural model (virtual model) of an as‐built wind turbine blade. The goal is to develop and demonstrate an approach to produce an accurate and detailed model of the as‐built blade for use in verifying the performance of the operating two‐bladed, downwind rotor. The digital twin model development methodology, presented herein, involves a novel calibration process to integrate a wide range of information including design specifications, manufacturing information, and structural testing data (modal and static) to produce a multi‐fidelity digital twin structural model: a detailed high‐fidelity model (i.e., 3D finite element analysis [FEA]) and consistent beam‐type models for aeroelastic simulation. A key element is that the multi‐fidelity structural digital twin method follows the rotor from the stages of design, to manufacturing, then to the ground testing and field operation. The result of this comprehensive approach is an accurate multi‐fidelity digital twin structural model for the geometric, structural, and structural dynamic properties of the as‐built blade within a 1% match in mass properties, 3.2% in blade frequencies, and 6% in deflection. The different stages of processing this information within the methodology are discussed. The rotor examined is the SUMR‐Demonstrator (SUMR‐D), which was installed on the Controls Advanced Research Testbed (CART‐2) wind turbine at the National Wind Technology Center. The digital twin model developed here was utilized to design controllers to safely operate SUMR‐D in field tests, which are providing additional data for further evaluation and development of the multi‐fidelity digital twin structural model.

Chetan, Mayank↗

DOE OSTI2021

Control co-design of 13 MW downwind two-bladed rotors to achieve 25% reduction in levelized cost of wind energy

Wind energy is recognized worldwide as cost-effective and environmentally friendly and is among the fastest-growing sources of electrical energy. To further decrease the cost of wind energy, wind turbines are being designed at ever larger scales, which is challenging due to greater structural loads and deflections. Large-scale systems such as modern wind turbines increasingly require a control co-design approach, whereby the system design and control design are performed in a more integrated fashion. We overview a two-bladed downwind morphing rotor concept that is expected to lower the cost of energy at wind turbine sizes beyond 13 megawatts (MW) compared with continued upscaling of traditional three-bladed upwind rotor designs. We describe an aero-structural-control co-design process that we have used in designing such extreme-scale wind turbines, and we discuss how we were able to achieve a 25% reduction in levelized cost of energy for our final turbine design compared to a conventional upwind three-bladed rotor design.

17 WIND ENERGY↗

DOE OSTI2021

Structural design and optimization of a series of 13.2 MW downwind rotors

The quest for reduced LCOE has driven significant growth in wind turbine size. A key question to enable larger rotor designs is how to configure and optimize structural designs to constrain blade mass and cost while satisfying a growing set of challenging structural design requirements. In this paper, we investigate the performance of a series of three two-bladed downwind rotors with different blade lengths (104.3-m, 122.9-m, and 143.4-m) all rated at 13.2 MW. The primary goals are to achieve 25% rotor mass and 25% LCOE reduction. A comparative analysis of the structural performance and economics of this family rotors is presented. To further explore optimization opportunities for large rotors, we present new results in a root and spar cap design optimization. In summary, we present structural design solutions that achieve 25% rotor mass reduction in a SUMR13i design (104.3-m) and 25% LCOE reduction in a SUMR13C design (143.4-m).

Yao, Shulong↗

DOE OSTI2020

Gravo-aeroelastic scaling of a 13-MW downwind rotor for 20% scale blades

A 105-m, 13-MW two-bladed downwind Segmented Ultralight Morphing Rotor (SUMR-13) blade was gravo-aeroelastically scaled by 20% to a 20.87-m-long demonstrator blade and confirmed through structural ground testing. The subscale model was achieved through geometric scaling and by aeroelastic scaling principles based on operational flapwise deflections combined with rotational and structural frequencies while retaining the turbine tip-speed ratio. In particular, the subscale demonstrator was designed to replicate, as closely as possible, the nondimensional geometry, the ratio of centrifugal to gravitational moments, the tip-speed ratio, and the nondimensional rotation rate. The intent for this demonstrator was to achieve the same nondimensional flapwise blade deflections and dynamics of the full-scale 13-MW rotor. The manufactured SUMR-D blade resulted in less than half of the mass of the conventional two-bladed Controls Advanced Research Turbine (CART2) rotor blade based on scaling and a lower power rating, though with some differences in mass and stiffness from the ideal scaled-down design to meet safety requirements at the test site. To achieve proper scaling, operational pitch control set points were altered to account for the differences by evaluating simulated operation of both the SUMR-13 and SUMR-D rotors. Structural testing of the SUMR-D blade investigated the response to well-defined flapwise loads and indicated that the subscale blade had the appropriate elastic properties needed for both scaling and for safe operational field testing.

17 WIND ENERGY↗

DOE OSTI2020

A gravo-aeroelastically scaled wind turbine rotor at field-prototype scale with strict structural requirements

A new sub-scale field-prototype design solution is developed to realize the dynamics, structural response, and distributed loads (gravitational, aerodynamic, centrifugal) that are characteristic of a full-scale large, modern wind turbine rotor. Prior work in sub-scale wind turbine testing has focused on matching aerodynamic/aero-elastic characteristics of full-scale rotors at wind tunnel scale. However, large-scale rotor designs must expand beyond this limited set of scaling parameters for cost-effective prototyping and meet strict requirements for structural safety for field testing. Here, the challenge lies in producing a structural design meeting two competing objectives: novel scaling objectives that prescribe the sub-scale blade to have low mass and stiffness; and traditional structural safety objectives that drive the design to have higher stiffness and mass. A 20% gravo-aeroelastically scaled wind turbine blade is developed successfully that satisfies these competing objectives. First, it achieved close agreement for non-dimensional tip deflection and flap-wise blade frequency (both within 2.1%) with a blade mass distribution constrained to produce target gravitational and centrifugal loads. Second, the entire blade structure was optimized to ensure a safe, manufacturable solution meeting strict strength requirements for a testing site that can experience up to 45 m/s wind gusts. The prototype-scale blade was fabricated and successfully proof-load tested.

17 WIND ENERGY↗