Search NASA⌕ Search

Engineering topics

Chodukowski, T

Publications and source records attributed to Chodukowski, T.

Laser-produced aluminum plasma expansion inside a plastic plasma envelope

Previous experimental results demonstrated that the plasma pressure decreases with the growing atomic number of the target material. In this context, a question arose if the Al plasma outflow could be collimated using the plastic plasma as a compressor. To solve this problem, an experiment using a plastic target with an Al cylindrical insert was performed. The focal spot diameter substantially larger than that of the insert ensured simultaneous heating both target materials. This experiment proved that a production of Al plasma jets collimated by an action of outer plastic plasma is feasible [Kasperczuk et al., Laser Part. Beams 30, 1 (2012)]. The results of investigations presented here provide additional information on distributions of electron temperature in the outflowing plasma and time and space characteristics of ion emission, both registered at bare and constrained-flow Al targets. The experiment was carried out at the Prague asterix laser system iodine laser facility. The laser provided a 250 ps (full width at half maximum) pulse with the energy of 130 J at the third harmonic frequency ({lambda}{sub 3} = 0.438 {mu}m). A plastic target with an Al cylindrical insert of 400 {mu}m in diameter as well as a bare Al target (for comparison) was used. The focal spot diameter ({Phi}{sub L}) 1200 {mu}m ensured the lateral pressure effect of the plastic plasma strong enough to guarantee the effective Al plasma compression. The electron temperature measurements have shown that such Al plasma compression is accompanied by the increase of its temperature, dominance of which starts at distance of 0.5 mm from the target surface. Measurements of ion emission characteristics confirm the earlier numerical simulation prediction that in these conditions the plasma expansion geometry is closer to planar. The constrained Al plasma jet is very narrow and its axial velocity is considerably larger than the velocity of freely expanding Al plasma stream. It means that the plastic plasma envelope, besides the Al plasma compression, also strongly accelerates the Al plasma in its axial motion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Highly efficient accelerator of dense matter using laser-induced cavity pressure acceleration

Acceleration of dense matter to high velocities is of high importance for high energy density physics, inertial confinement fusion, or space research. The acceleration schemes employed so far are capable of accelerating dense microprojectiles to velocities approaching 1000 km/s; however, the energetic efficiency of acceleration is low. Here, we propose and demonstrate a highly efficient scheme of acceleration of dense matter in which a projectile placed in a cavity is irradiated by a laser beam introduced into the cavity through a hole and then accelerated in a guiding channel by the pressure of a hot plasma produced in the cavity by the laser beam or by the photon pressure of the ultra-intense laser radiation trapped in the cavity. We show that the acceleration efficiency in this scheme can be much higher than that achieved so far and that sub-relativisitic projectile velocities are feasible in the radiation pressure regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma-wall interaction studies with optimized laser-produced jets

The production of the laser-produced plasma jets at burnt-through low-Z foils was optimized by using three-frame interferometry. When striking secondary targets, these jets of energetic particles represent an efficient tool for the investigation of transient phenomena at surfaces of the plasma-exposed solids. Two sets of precisely measured x-ray spectroscopic data demonstrate diagnostic potential of the collimated jets in the plasma-wall interaction studies: Blue Doppler shifts of the Al jet self-emission visualize ion deceleration in the near-wall region. Local depressions found in Al Ly{gamma} profiles emitted from Al/Si(PMMA) targets indicate charge exchange between the Al XIII and fully stripped C ions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interaction of Cu and plastic plasmas as a method of forming laser produced Cu plasma streams with a narrow jet or pipe geometry

This brief communication is aimed at investigations of interaction of axially symmetrical light (plastic) plasma with heavy (copper) plasma. The use of axially symmetrical target compositions consisting of materials with low and high atomic numbers makes it possible to create different plasma stream configurations (e.g., very narrow jet or pipe). In the paper certain their applications are suggested.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental evidence of thermonuclear neutrons in a modified plasma focus

The PF-1000 plasma focus was modified by adding the cathode disk 3 cm in front of the anode. This modification facilitated the evaluation of neutron energy spectra. Two neutron pulses were distinguishable. As regards the first neutron pulse, it lasted 40 ns during the plasma stagnation and it demonstrated high isotropy of neutron emission. A peak neutron energy detected upstream was 2.46{+-}0.02 MeV. The full width of neutron energy spectra of 90{+-}20 keV enabled to calculate an ion temperature of 1.2 keV. These parameters and a neutron yield of 10{sup 9} corresponded to theoretical predictions for thermonuclear neutrons.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Influence of low atomic number plasma component on the formation of laser-produced plasma jets

The results of investigations are presented that are connected with a very simple method of plasma jet formation, which consists in irradiating a massive planar target made of material with relatively high atomic number by a partly defocused laser beam. This brief communication is aimed at investigations of interaction of axially symmetrical light (plastic-CH) plasma with heavy (copper) plasma. It demonstrates that a relatively thin plastic plasma envelope can compress the Cu plasma and control the Cu-jet formation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Highly efficient acceleration and collimation of high-density plasma using laser-induced cavity pressure

An efficient scheme of acceleration and collimation of dense plasma is proposed and examined. In the scheme, a target placed in a cavity coupled with a guiding channel is irradiated by a laser beam introduced into the cavity through a hole and accelerated along the channel by the pressure of the ablating plasma confined in the cavity. Using 1.315 mum, 0.3 ns laser pulse of energy up to 200 J and a thin CH target, it was shown that the energetic efficiency of acceleration in this scheme is an order of magnitude higher than in the case of conventional ablative acceleration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cavity pressure acceleration: An efficient laser-based method of production of high-velocity macroparticles

We propose an efficient method of accelerating macroparticles to high velocities, which employs pressure of the plasma produced by a focused pulsed high-power laser beam inside a cavity-type target. That is why we have called it the cavity pressure acceleration (CPA) scheme. The method was tested during our experiments at the Prague Asterix Laser System, the results of which are reported here. They show that CPA makes it possible to accelerate both light and heavy macroparticles in arbitrary direction, with the acceleration efficiency far exceeding that achieved upto now by using the classic ablative acceleration scheme. High velocities of the macroparticles (foil fragments) produced and possibility of accelerating even rather heavy macroparticles are promising from the point of view of impact fusion studies, of the impact fast ignition, in particular.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Formation of a supersonic laser-driven plasma jet in a cylindrical channel

A simple method of supersonic plasma jet production where the jet is formed in a cylindrical channel guiding the plasma generated from a laser-irradiated thin foil target is proposed and examined. High-Mach number ({>=}10) plasma jets of parameters relevant to laboratory astrophysics applications using 120 J, 1.315 {mu}m, and 0.3 ns laser pulse for a thin CH foil irradiation are demonstrated. The method seems to be flexible in the production of jets of various compositions and hydrodynamic parameters and does not require high-energy lasers for the jet generation.

79 ASTRONOMY AND ASTROPHYSICS↗