Engineering topics

Choi, S. R.

Publications and source records attributed to Choi, S. R..

18 records

NASA NTRS2005

Fracture Toughness in Advanced Monolithic Ceramics - SEPB Versus SEVENB Methods

Fracture toughness of a total of 13 advanced monolithic ceramics including silicon nitrides, silicon carbide, aluminas, and glass ceramic was determined at ambient temperature by using both single edge precracked beam (SEPB) and single edge v-notched beam (SEVNB) methods. Relatively good agreement in fracture toughness between the two methods was observed for advanced ceramics with flat R-curves; whereas, poor agreement in fracture toughness was seen for materials with rising R-curves. The discrepancy in fracture toughness between the two methods was due to stable crack growth with crack closure forces acting in the wake region of cracks even in SEVNB test specimens. The effect of discrepancy in fracture toughness was analyzed in terms of microstructural feature (grain size and shape), toughening exponent, and stable crack growth determined using back-face strain gaging.

Choi, S. R.↗

NASA NTRS2005

Foreign Object Damage Resistance of Uncoated SiC/SiC Composites

2-D woven SiC/SiC composites fabricated by melt infiltration method were impact tested at room temperature and at 1316 C in air using 1.59 mm steel-ball projectiles at projectile velocities ranging from 110 m/s to 400 m/s. The extent of substrate damage with increasing projectile velocity was imaged and analyzed using optical microscopy and nondestructive evaluation (NDE) methods. The impacted specimens were flexure and tensile tested at room temperature to determine their residual mechanical properties. Results indicate that as the projectile velocity increases, internal damage in the target material also increases and the mechanical properties degrade. At velocities > 300 m/s, the projectile penetrates through the target material, but it still retains approx. 50% ultimate strength of the as-fabricated composites and exhibits non-brittle failure.

Bhatt, R. T.↗

NASA NTRS2004

Foreign Object Damage Resistance of Uncoated and EBC Coated SiC/SiC Composites

SiC/SiC composites fabricated by the melt infiltration method are candidate materials for the turbine components such as combustor liners, nozzle vanes and blades because of their high temperature strength, and thermal conductivity. To avoid surface recession in a combustion environment containing moisture, these materials also require an environmental barrier coating (EBC). Under thermal loading condition alone, the EBC coated SiC/SiC components show microstructural and strength stability after -1 5000 hr exposure to 12OO0C in combustion environment. However, the stability of SiC/SiC composites under impact conditions is not fully understood. In this study, both uncoated and EBC coated SiC/SiC composite specimens were impact tested by steel-ball projectiles at room temperature and at 1300 C in air. After impact, the specimens were analyzed under a scanning electron microscope to assess coating damage, and then tensile and bend tested at room temperature to determine their residual strength. The extent of coating and substrate damage with increasing projectile velocity was imaged and analyzed using nondestructive evaluation (NDE) methods such as micro focus x-ray radiography, tomography, and thermal wave imaging. The mechanical property results of impacted specimens are correlated with the NDE results and the scanning electron microscopy (SEM) observations. Influence of projectile velocity on impact damage of the coating/substrate, and the implication coating damage on durability of the composite will be discussed.

Bhatt, R. T.↗

NASA NTRS2004

Solid Oxide Fuel Cell Seal Development at NASA Glenn Research Center

Researchers at NASA GRC are confronting the seal durability challenges of Solid Oxide Fuel Cells by pursuing an integrated and multidisciplinary development effort incorporating thermo-structural analyses, advanced materials, experimentation, and novel seal design concepts. The successful development of durable hermetic SOFC seals is essential to reliably producing the high power densities required for aerospace applications.

Steinetz, Bruce M.↗

NASA NTRS2002

Quasistatic vs. Dynamic Modulus Measurements Of Plasma-Sprayed Thermal Barrier Coatings

Plasma-sprayed 8wt% yttria-stabilized zirconia (8YSZ) thermal barrier coatings (TBCs) have been demonstrated to exhibit nonlinear hysteretic elastic behavior by quasistatic cyclic compression and cylindrical punch indentation measurements. In particular, the instantaneous (tangential) elastic modulus increases with applied stress and exhibits significant hysteresis during cycling. Sound velocity (dynamic) measurements also show an increase in TBC modulus with applied compressive stress, but in contrast show no significant hysteresis for the modulus during cycling. The nonlinear elastic behavior of the TBCs evidenced by these tests is attributed to coating compaction and internal sliding. The differences between the quasistatic and dynamic measurements are explained by the relative absence of the effect of internal sliding in the dynamic modulus measurements. By incorporating short load reversals into the larger loading cycle and measuring the instantaneous modulus at the start of each load reversal, the effects of internal sliding can be substantially reduced in the quasistatic measurements, and the resulting modulus values show good agreement with the modulus values determined by dynamic sound velocity measurements.

Eldridge, J. I.↗

NASA NTRS2001

Development of Tough, Strong, and Pest-Resistant MoSi2-(Beta)Si3N4 Composites for High-Temperature Structural Applications

A new MoSi2-base composite was developed that contains in-situ reinforcement of whisker-type beta-Si3N4 grains in a MoSi2 matrix. The advantages of this in-situ reinforced MoSi2-Si3N4 are lower density, higher fracture toughness and better strength than typical MoSi2 alloys, combined with excellent environmental and pest resistance. The average fracture toughness of the in-situ reinforced material determined by one technique was 12.2 MPa.m(exp 1/2) compared to 4.9 to 5.5 MPa.m(exp 1/2) for similar materials with the exception that the beta-Si3N4 had a blocky morphology as opposed to the whisker-like morphology typical of the in-situ toughened material. This MoSi2-(beta)Si3N4 was also resistant to pesting at intermediate temperatures (400 to 600 C) even when precracked or under applied load; conditions that would quickly reduce typical MoSi2 alloys to oxidized powder.

Hebsur, M. G.↗

NASA NTRS2001

Slow Crack Growth Analysis of Advanced Structural Ceramics Under Combined Loading Conditions: Damage Assessment in Life Prediction Testing

Slow crack growth analysis was performed with three different loading histories including constant stress- rate/constant stress-rate testing (Case I loading), constant stress/constant stress-rate testing (Case II loading), and cyclic stress/constant stress-rate testing (Case III loading). Strength degradation due to slow crack growth and/or damage accumulation was determined numerically as a function of percentage of interruption time between the two loading sequences for a given loading history. The numerical solutions were examined with the experimental data determined at elevated temperatures using four different advanced ceramic materials, two silicon nitrides, one silicon carbide and one alumina for the Case I loading history, and alumina for the Case II loading history. The numerical solutions were in reasonable agreement with the experimental data, indicating that notwithstanding some degree of creep deformation presented for some test materials slow crack growth was a governing mechanism associated with failure for all the rest materials.

Choi, S. R.↗

NASA NTRS1999

Elevated-Temperature "Ultra" Fast Fracture Strength of Advanced Ceramics: An Approach to Elevated-Temperature "Inert" Strength

The determination of "ultra" fast fracture strengths of five silicon nitride ceramics at elevated temperatures has been made by using constant stress-rate ("dynamic fatigue") testing with a series of "ultra" fast test rates. The test material included four monolithic and one SiC whisker-reinforced composite silicon nitrides. Of the five test materials, four silicon nitrides exhibited the elevated -temperature strengths that approaches their respective room-temperature strengths at an "ultra" fast test rate of 3.3 x 10(exp 4) MPa/s. This implies that slow cracks growth responsible for elevated-temperature failure can be eliminated or minimized by using the "ultra" fast test rate. These ongoing experimental results have shed light on laying a theoretical and practical foundation on the concept and definition of elevated-temperature "inert" strength behavior of advanced ceramics.

Choi, S. R.↗

NASA NTRS1993

Fracture Toughness of PMMA as Measured with Indentation Cracks

Fracture toughness of polymethyl methacrylate (PMMA) was evaluated with indentation cracks. The cracks were developed by indenting in a liquid acetone environment, as suggested by previous researchers. Due to the inconsistency in crack configurations with varying indentation loads and to the negligible residual stress from indentation, the application of the indentation strength method was limited in evaluating fracture toughness of PMMA. The semi-elliptical crack approximation, however, particularly at a low indentation load of 9.8 N, resulted in reasonable agreement with the value determined by three conventional fracture toughness testings using the compact tension (CT), double cantilever beam (DCB), and single edge notched beam (SENB) specimens. Measurements at other indentation load typically were in poor agreement with conventional methods due to poorly developed crack configurations.

Choi, S. R.↗

NASA NTRS1993

Interaction of Cracks Between Two Adjacent Indents in Glass

Experimental observations of the interaction behavior of cracks between two adjacent indents were made using an indentation technique in soda-lime glass. It was specifically demonstrated how one indent crack initiates and propagates in the vicinity of another indent crack. Several types of crack interactions were examined by changing the orientation and distance of one indent relative to the other. It was found that the residual stress field produced by elastic/plastic indentation has a significant influence on controlling the mode of crack interaction. The interaction of an indent crack with a free surface was also investigated for glass and ceramic specimens.

Choi, S. R.↗

NASA NTRS1993

Evaluation of the Fracture Toughness of Nb-40Al-8Cr-1W-1Y-0.05B Intermetallic Material by Indentation Techniques

The fracture toughness of an Nb-40Al-8Cr - 1W-1Y-0.05B intermetallic material was evaluated by indentation techniques at room temperature. Two widely used indentation methods, crack size measurement and indent strength, yielded excellent agreement with a conventional fracture toughness technique using straight-through precracked specimens, despite the occasional formation of poorly configured cracks. However, the modified indentation technique, using dummy indent flaws, resulted in a low fracture toughness compared to that evaluated by the other methods. The material did not exhibit rising R-curve behavior, as evaluated from the indentation strength data. These results indicate that indentation fracture principles are applicable to this brittle intermetallic material without modification of the residual contact stress term originally calibrated for ceramic materials.

Choi, S. R.↗

NASA NTRS1992

Mechanical behaviour and failure phenomenon of an in situ toughened silicon nitride

The Weibull modulus, fracture toughness and crack growth resistance of an in-situ toughened, silicon nitride material used to manufacture a turbine combustor were determined from room temperature to 1371 C. The material exhibited an elongated grain structure that resulted in improved fracture toughness, nonlinear crack growth resistance, and good elevated temperature strength. However, low temperature strength was limited by grains of excessive length (30 to 100 microns). These excessively long grains were surrounded by regions rich in sintering additives.

Salem, J. A.↗

NASA NTRS1992

Crack healing behavior of hot pressed silicon nitride due to oxidation

It is shown that limited oxidation of an MgO-containing, hot-pressed silicon nitride ceramic at 800 deg C and above results in increased strength due to crack healing. Slight oxidation of the surface produces enstatite and cristobalite which fills in cracks. More extensive oxidation leads to strength degradation due to the formation of new flaws by the evolution of N2 gas at the surface. The apparent fracture toughness also increased at 800 deg C and above due to oxidation. Bonds formed between the two surfaces of the crack during oxidation leads to a reduction in stress intensity at the crack tip, suggesting that valid high-temperature toughness values cannot be obtained in an air environment. The increase in strength due to crack healing by oxidation can be achieved without compromising the fatigue properties of the silicon nitride ceramic.

Choi, S. R.↗

NASA NTRS1992

Strength, toughness and R-curve behaviour of SiC whisker-reinforced composite Si3N4 with reference to monolithic Si3N4

The flexural strength and fracture toughness of 30 vol pct SiC whisker-reinforced Si3N4 material were determined as a function of temperature from 25 to 1400 C in an air environment. It was found that both strength and toughness of the composite material were almost the same as those of the monolithic counterpart. The room-temperature strength was retained up to 1100 C; however, appreciable strength degradation started at 1200 C and reached a maximum at 1400 C due to stable crack growth. In contrast, the fracture toughness of the two materials was independent of temperature with an average value of 5.66 MPa sq rt m. It was also observed that the composite material exhibited no rising R-curve behavior at room temperature, as was the case for the monolithic material. These results indicate that SiC whisker addition to the Si3N4 matrix did not provide any favorable effects on strength, toughness and R-curve behavior.

Choi, S. R.↗

NASA NTRS1984

Blade tip geometry - A factor in abrading sintered seal material

Experimental results are presented for the case of titanium blade tip specimens of various geometrical configurations rubbing at 100 m/s against specimens of nickel-chromium sintered powder metal seal material, the latter being fed toward the rotating blades at an incursion rate of 0.0254 mm/s. Blade tips in the form of orthogonal cutting tools with about 85 deg negative rake angles exhibited desirable abrading capabilities, as measured by the tear-free appearance of the grooves they generated in the seal material, little wear of blade tips, low forces of interaction and low seal densification. Similar results have been obtained for blade specimens with tips of small radius of curvature, as well as for square-ended and slanted blade tips that are plasma-sprayed with abrasive particles. The relationship between the size of these particles and their abrading effectiveness is considered.

Wolak, J.↗

NASA NTRS1983

An experimental investigation and numerical prediction of thermomechanical phenomena in high speed rotor tip rubbing

A thermomechanical study of the intermittent rubbing of a rotor blade tip and a casing seal is carried out taking into account the existence of thermal contact resistance. The effect of the thermal properties of a plasma sprayed coating on the blade tip is studied. The influence of a variable heat generation and variable thermal contact resistance at the blade tip as it passes along the path of rubbing is also discussed.

Emery, A. F.↗

NASA NTRS1982

Preliminary results on the abradability of porous, sintered seal material

Preliminary results are presented for the case of titanium blade specimens, with bare tips (or covered with wear resistant, plasma sprayed materials) rubbing at 100 m/s against specimens of abradable nickel-chromium seal material moving toward the rotating blades at 0.0125 mm/s or at 0.025 mm/s. Using a two component dynamometer, the normal force of the rub interaction was measured and the shear component estimated. The elastoplastic properties of the seal material have been determined and those parameters as well as the rigidity of the rub tester system are considered in conjunction with those affecting the accuracy of the measurement of the forces arising at the blade-seal interface. The average and the 'local instantaneous' temperatures of the seal specimen and the temperature of the blade tip surface during rubbing are presented as functions of time. A seal densification factor is defined and its functional relationships with contact force components, temperature, wear ratio and blade tip abrading capability are indicated.

Wolak, J.↗

NASA NTRS1982

An experimental investigation of interfacial temperatures in blade-seal material rubbing of aircraft compressors

Results are presented for the rubbing of rotating (100 m/s) titanium blade specimens, with different plasma-sprayed tip coating, against an abradable porous seal material at two different incursion rates. In general, there was a good correspondence between the average transverse force of rubbing and the seal specimen surface temperature. Instantaneous seal surface temperature measurement showed a significant temperature jump before and after each rubbing with a high rate of cooling during each revolution and a high overall temperature level. Numerical predictions of both blade and seal temperature agreed well for the bare blade tip experiments but were consistently high for the coated blades. This suggests that the thermal properties of the coatings may significantly affect the temperatures and hence the wear characteristics of the system.

Emery, A. F.↗