Engineering topics
Publications and source records attributed to Chopra, M. A..
Report describes experimental and theoretical study of effect of thermal convection on shape of interface between solid and liquid succinonitrile, clear commercially available plastic, in Bridgman (directional-solidification) apparatus in vertical and horizontal orientations.
Thermosolutal convection caused by the solute build up ahead of the growing arrays of cells and dendrites results in macrosegregation along the length of the Pb-Sn alloy (10 to 58 wt pct Sn) specimens when they are directionally solidified in a positive thermal gradient (melt on top, solid below, and gravity pointing down). At a constant thermal gradient, the extent of macrosegregation increases with decreasing growth speed as the microstructure changes from dendritic, to cellular and to planar. An empirical parameter, effective partition coefficient, obtained from the dependence of the longitudinal macrosegregation on fraction distance solidified can be used to represent the extent of macrosegregation.
The influence of convection on the development of morphological instability at the liquid-solid interface during directional solidification in a positive thermal gradient has been examined in Pb-10 wt pct Sn and succinonitrile-1.9 wt pct acetone. The onset of interfacial breakdown occurs at higher growth speeds in the presence of convection. The linear stability analysis due to Favier and Rouzaud which uses the 'deformable' mass flow boundary layer concept shows a good agreement with the experimentally observed behavior.
The dependence of primary arm spacings on growth speed has been investigated for cellular and dendritic arrays in directionally solidified Pb-10 wt pct Sn. The spatial arrangements of cells and dendrites, as given by their coordination number, are not very different from each other. The primary arm spacing maxima and the cell-to-dendrite transition appear to be strongly influenced by the magnitude of the solute partition coefficient (k). The planar-to-cellular transition in Pb-Sn (k = 0.50) is supercritical as compared to the subcritical behavior reported in Al-Cu (k = 0.14) and succinonitrile-acetone (k = 0.1).
The effect of thermal convection on the shape of solid-liquid interface was investigated in experiments conducted in a transparent Bridgman-type directional solidification furnace. The relationship was numerically modeled using a standard 2D finite-difference approach, with the solid-liquid deformable interface approximated by a blocking-off technique. The directional solidification furnace was used with pure succinonitrile (which is also transparent) contained in a long square ampoule made of borosilicate glass. With the furnace in the vertical configuration, a flat interface was observed, in agreement with the model. On the other hand, a highly distorted interface was obtained in the horizontal configuration; the numerical results showed a strong recirculating cell in front of the interface due to natural thermal convection. The results indicate that thermal convection is responsible for the interface distortion.
Liquid-solid interface distortion in the region of primary dendrite tips has been investigated in directionally solidified Pb-8 wt pct Au alloy. The distortions are caused by thermosolutal convection despite choice of growth conditions which should have been thermally and solutally stabilizing. The convection produces clustering of primary dendrites on a plane perpendicular to the growth direction. It produces a mushy zone, where the primary dendrites do not protrude with a uniform length, across the specimen cross section, resulting in large macrosegregation in the transverse direction. However, little macrosegregation is observed along the growth direction. The mushy zone, with uneven dendrite lengths, forms in the beginning of directional solidification. Its shape and dendrite distribution do not show much change during subsequent solidification. Tip morphologies of primary dendrites, within the dendrite clusters, appear to follow the morphological stability relationship.
The dependence of primary arm spacings on growth speed was investigated for cellular and dendritic arrays in Pb-10 wt percent Sn samples directionally solidified under a constant positive thermal gradient in the melt. The gradient of constitutional supercooling was varied from almost zero (near the break-down of the planar liquid-solid interface at small growth speeds, cellular morphology) to near unity (large growth speeds, dendritic morphology). The spatial arrangements of cells and dendrites, as given by their coordination number, are not very different from each other. It appears that primary arm spacing maxima and the cell to dendrite transition are strongly influenced by the magnitude of the solute partition coefficient. The planar to cellular bifurcation is supercritical in Pb-Sn which has a high partition coefficient, as compared to the subcritical behavior reported in Al-Cu and succinonitrile-acetone, both of which have low partition coefficients. The primary arm spacing model due to Hunt agrees with the experimentally observed trend for the whole growth regime. There is a good quantitative agreement at higher gradients of supercooling. However, the model overpredicts the primary arm spacings at low gradients of constitutional supercooling.
The dependence of primary arm spacings on growth speed was investigated for cellular and dendritic arrays in Pb-10 wt percent Sn samples directionally solidified under a constant positive thermal gradient in the melt. The gradient of constitutional supercooling was varied from almost zero (near the break-down of the planar liquid-solid interface at small growth speeds, cellular morphology) to near unity (large growth speeds, dendritic morphology). The spatial arrangements of cells and dendrites, as given by their coordination number, are not very different from each other. It appears that primary arm spacing maxima and the cell to dendrite transition are strongly influenced by the magnitude of the solute partition coefficient. The planar to cellular bifurction is supercritical in Pb-Sn which has a high partition coefficient, as compared to the subcritical behavior reported in Al-Cu and succinonitrile-acetone, both of which have low partition coefficients. The primary arm spacing model due to Hunt agrees with the experimentally observed trend for the whole growth regime. There is a good quantitative agreement at higher grdients of supercooling. However, the model overpredicts the primary arm spacings at low gradients of constitutional supercooling.
Alloys generally solidify dendritically, and associated with that is the microsegregation of impurities. Pure metals also solidify in dendritic form as 'thermal' dendrites, which actually segregate the system's enthalpy. In this investigation, small additions of solute to succinonitrile have been studied and dendritic growth observed in a supercooled melt. This free dendritic growth-mode is similar to that experienced by equiaxed dendrites found in alloy castings. Observations of these free dendrites include measurement of velocity and tip radius of the dendrites at different supercoolings and solute concentrations.
The diffusion coefficient of acetone in liquid succinonitrile at 331.1 K was determined using the method of McBain and Dawson (1935). Only dilute mixtures of SCN-acetone were studied. The interdiffusion constant was determined to be 0.0000127 sq cm/s and was essentially independent of the acetone concentration over the range investigated (0.5 to 18 mol pct acetone).