Engineering topics

Chowdhury, Mehrin

Publications and source records attributed to Chowdhury, Mehrin.

3 records

DOE OSTI2022

Design and performance analysis of a Swirl Pintle injector for a 1 MW th pressurized oxy-coal combustor

Pressurized Oxy-coal combustion has the potential to achieve high thermal efficiency by recovering the latent heat of steam from flue gases and providing options for up to 95% carbon capture. Here, this study proposes a novel burner technology for pressurized oxy-coal combustion and investigates its operability. Three burner versions are designed and tested; no swirl, swirl numbers 0.9 and 1.2 to identify optimum design parameters and performance. A commercially available Dantec Dynamics software is used to conduct the shadowgraph experiments to observe burner performance. Coal water slurry is used as fuel with three different slurry ratios where the coal percentage by weights were 30, 40 and 50. Droplet size, distribution, spray angle and jet breakup lengths are measured and analyzed to quantify the performance. The study found that increasing the swirl number enhanced atomization. Implementing swirlers allowed the jet to spread through faster primary jet separation, thus improving atomization. In addition, higher slurry ratios improved the generation of smaller particles. However, it was also found that excessive increases in oxidizer momentums negatively impact the atomization process by jet shrinkage. The study concluded that operating a pintle burner at 1.2 swirl conditions with a 40/60 slurry ratio produces optimum performance.

42 ENGINEERING↗

DOE OSTI2020

Design and Operability of a Pressurized Oxy Combustion System

Fossil fuel powers more than two-thirds of the world’s electricity, a significant share of which is derived from coal power plants. Despite coal being an abundant and energy-rich fuel, the major halt to its progress is greenhouse gas emissions. Pressurized oxy-combustion cycles can achieve theoretically high thermal efficiencies along with a 90% carbon capture rate. Additionally, the high energy density allows smaller turbomachinery and save capital cost. Thus, the primary objective of this dissertation is to present the design and operability of a pressurized oxy-combustor system. The initial part of the dissertation investigates different thermodynamic cycles and presents a model that can be adapted for existing power plants. The thermodynamic model will be used in the later part to design the proposed combustor. The two cycles analyzed are ENEL and TIPS. This study focuses on qualitative analyses of the cycles using a commercially available software called Aspen Plus®. A detailed benchmark study has been performed to validate the modeling process. ENEL and TIPS cycles are designed in the software, adopting the same principles. Recirculation ratio and pressures are varied to find the efficiency range of the cycles. Power calculations are done to find overall and net efficiency for a fixed recirculation ratio. The efficiencies of the cycles are compared to select an optimum cycle. A recirculation ratio of 50% is selected for implementation. The comparison shows that ENEL is marginally efficient over TIPS, at the cost of a pressure difference of about 70bars. Technology Readiness Level analysis is performed to present the availability of the specialized equipment for the cycles. From the TRL analysis, it is seen that the cost and availability of high viii pressure equipment surmount the edge of TIPS over ENEL. Thus, ENEL is chosen as the better cycle for investigating a scaled experiment considering efficiency and viability. The later part of the dissertation focuses on developing the combustor's design for a pressurized oxy-combustion cycle. The proposed combustor is a powerhead-mounted design aimed to produce 1MW of thermal outputThe different aspects of the design of a down-fired pressurized swirl combustor are presented in this dissertation.

Chowdhury, Mehrin↗

DOE OSTI2020

Characterization of Oxy-Coal Swirl Injector

The article presents the design and testing of a coal-slurry swirl-pintle injector for high pressure oxy-coal combustion systems. Pressurized oxy-coal combustion-based systems have the potential to improve efficiency by recovering latent heat of the steam in flue gas and achieve 90% CO2 capture. In oxy-coal combustion, coal is burned in the presence of pure oxygen, which results in higher efficiency and less greenhouse gas in the exhaust. With the advancement of pressurized oxy-coal combustor research, there is a need to investigate injector technology suitable for this unique combustion approach. Effective atomization and mixing of coal-slurry and oxidizer pose a challenge for the efficient burning of coal particles. A swirl-pintle type injector was designed and tested to enhance the atomization of the coal-water slurry spray by adding a swirl to the oxygen flow path. Although pintle type injectors are traditionally used in rocket engines, they present a promising approach in clean coal combustion technology due to higher mixing effectiveness and enhanced performance. The mixing behavior of three pintle injectors with different swirl numbers (S = 0, 0.9, and 1.2) was tested using a high-speed shadow sizing technique. Mixture ratios of 30% (by mass) coal-water slurry were studied. The droplet diameter and dispersion characteristics were determined from shadow images of coal-water spray. The jet breakup length, droplet number, total moment ratio (TMR), and Ohnesorge number were then calculated to compare the performance of different injectors. The paper presents an empirical correlation of the TMR with droplet size and spray regimes. For a pintle injector with S = 1.2 swirler, the droplets diameter was found to be in the range of 1 mm to 12 mm. The jet breakup length was also shorter in comparison to S= 0 and 0.9 injectors. A second atomization zone was also observed at 2 and 5 diameters downstream of injector exist at spray edge and jet core respectively

01 COAL, LIGNITE, AND PEAT↗