TPSAS-NF1676L-33558-DND
Explore the source record for details and available documents.
Carlie H Zumwalt↗
Engineering topics
Chris Karlgaard
Publications and source records attributed to Chris Karlgaard.
Mars Entry Instrumentation Flight Data and Mars 2020 Entry Environments
On February 18th, 2021, the Mars 2020 entry vehicle delivered the Perseverance rover to the surface of Mars. The entry vehicle carried a set of instrumentation installed on the heatshield and backshell to measure aerodynamic and aerothermal performance, named the Mars Entry, Descent, and Landing Instrumentation 2. This set of instrumentation included pressure transducers, thermocouples, heatflux sensors, and a radiometer, as well as a dedicated sensor support electronics system. All MEDLI2 hardware operated as expected during cruise and entry. MEDLI2 sensors gathered accurate pressure measurements in hypersonic through supersonic regimes to reconstruct vehicle attitude and atmospheric profiles. MEDLI2 on the heatshield sensors indicated that surface temperatures, caused by turbulent heating beginning 70 seconds after entry, remained at or below 1430 °C, while heatshield bondline temperatures rose less than 45 °C. Backshell surface TPS temperatures peaked at 630 °C, which was caused primarily by radiative heating measured by several separate sensors. The MEDLI2 temperature and pressure measurements enabled further detailed characterization of the Mars 2020 entry performance, and the flight dataset will provide a wealth of information for the EDL community and future mission designers.
thermal protection systems↗
Overview of The Dragonfly Entry Aerosciences Measurements (DrEAM) Suite
Overview of the Dragonfly EDL instrumentation suite known as Dragonfly Entry Aerosciences Measurements (DrEAM)
Aaron Brandis↗
Magnetic Suspension Wind Tunnel Reconstruction Using an Extended Kalman Filter Framework
Explore the source record for details and available documents.
Chris Karlgaard↗
Dragonfly Entry Aerosciences Measurements (DrEAM) Suite Science Objectives
NASA Ames and Langley are partnering with DLR to propose a comprehensive instrumentation suite known as the Dragonfly Entry Aerosciences Measurements (DrEAM). DrEAM will provide key aerothermodynamic data and performance analysis for Dragonfly’s forebody and backshell Thermal Protection System (TPS), and also includes a DLR-provided Data Acquisition System (DAS). Titan's atmosphere predominantly consists of nitrogen (~ 98% by mole) with small amounts of methane (~ 2% by mole). CN is a strong radiator and is found in nonequilibrium concentrations for Titan entry, the modeling of which has proven to be a difficult task. The DrEAM instrumentation suite will significantly advance the state-of-the-art not only by documenting the environment and performance of Dragonfly’s entry system but also by making key measurements in Titan’s atmosphere for the first time, thus providing new benchmark data applicable to entry science more generally.
Aaron Brandis↗
Results from the Helicopter Drop Test of the DAVINCI Descent Sphere
This paper summarizes the October 2023 helicopter drop test of the descent sphere of the upcoming Deep Atmosphere Venus Investigation of Noble gases, Chemistry, and Imaging mission to Venus. The drop test met its primary objectives of recording acceleration, attitude rates, and camera data during the 30-second descent at Utah Test and Training Range. The recorded inertial measurement unit and global position sensor receiver data has allowed a six degree-of-freedom reconstruction of the vehicle position, velocity, attitude, and attitude rates, as well as derived aerodynamic coefficients. Initial comparisons show good agreement between the reconstruction and the pre-flight models of the descent sphere being used by the Venus mission. The reconstructed aerodynamic coefficients from the drop test can inform updates to the aerodynamic model to be used for the actual Venus mission.
Soumyo Dutta↗
OSIRIS-REx Entry, Descent, and Landing Performance
The Origins, Spectral Interpretation, Resource Identification, Security, Regolith Explorer (OSIRIS-REx) was the third mission in NASA’s New Frontiers program. OSIRIS-REx launched out of Cape Canaveral, Florida on September 8, 2016, with a science goal to return a minimum of 60 g of a primitive asteroid’s surface, specifically the near-Earth asteroid Bennu. The sample return capsule (SRC) successfully touched down at UTTR on the morning of September 24, 2023. The entry, descent, and landing (EDL) sequence had an off-nominal deployment of the parachute, but the spacecraft safely landed within the pre-flight prediction of the landing ellipse and the payload was safely recovered. This paper discusses the pre-flight EDL modeling and simulation and focus on predictions for EDL operations. Flight observations such as timeline are compared to the predicted timeline produced by the EDL simulation.
EDL↗