Search NASA⌕ Search

Engineering topics

Christopher J. Wohl

Publications and source records attributed to Christopher J. Wohl.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Lunar Dust Mitigation: A Guide and Reference: First Edition (2021)

On the surface of the Moon, lunar dust specifically presents unique challenges to operations long-term due to regolith particles’ ubiquitous presence in the lunar environment, potential to electrostatically charge and possible chemical reactivity. Whether to avoid exposure, try to remove or simply to tolerate lunar dust infiltrating a system becomes a complex question involving length of required service life, dust effects and critical risks, mass and complexity trades for the entire system. This publication provides a snapshot of advice from topical experts for specific areas of concern to systems targeted for deployment on the lunar surface. Following introductory overview commentary, dust mitigation approaches appropriate to the lunar surface are first addressed for typically static structures such as optical surfaces, radiators, and other thermal control surfaces, followed by regolith exposure concerns for communications equipment and non-optical sensors. The broad topic of mechanisms and mechanical assemblies is broken down to address relevant component level concerns, such as for bearings and for seals. “Soft goods” components of space suits (fabric) specific concerns are discussed, followed finally by brief coverage of human health issues and concerns, though the emphasis of this publication remains with components directly exposed to the harsh lunar surface environment. A description of some lunar surface hazard details, in particular characteristics of lunar surface dust, follows in Appendix A, and more detailed explanations of quantification issues for particulates are in Appendix B. The simple inertial removal of particles from a surface is discussed in Appendix C, followed by a summary of terrestrial best practices for dust mitigation recommended within select industries in Appendix D. The aggregated bibliography of references, while extensive and very useful, should not be construed to be exhaustive and can serve as a constructive start.

dust↗
NASA NTRS2023

Protective Coatings for Lunar Dust Tolerance

Materials capable of withstanding the harsh lunar environment are critically needed to support long duration, sustainable missions on the Moon’s surface. Lunar dust significantly threatens the durability and reusability of components and vehicles due to possessing a fine, jagged morphology and highly abrasive nature. These characteristics result in the particles eroding, adhering and/or embedding onto component surfaces and into device confined geometries (e.g., gear housing, interlocking systems, etc.) potentially leading to premature failure. The aim of this study is to identify and characterize wear-resistant commercial-off-the-shelf (COTS) materials, including advanced ceramics, for use as protective coatings to minimize abrasion and adhesion caused by lunar dust. Preliminary testing that mimics various aspects of lunar dust degradation, such as abrasive wear and adhesion, suggests that COTS ceramic coatings can improve lunar dust tolerance and protect underlying metallic substrates.

Valerie. L. Wiesner↗
NASA NTRS2020

Lunar Dust Simulant Particle Adhesion on Copolyimide Alkyl Ethers

Mitigation of lunar dust contamination is one of the greatest challenges to be overcome to realize a sustained lunar presence. Likely solutions will integrate active mitigation strategies, requiring the input of external energy, and passive materials, exhibiting an intrinsic resistance to lunar dust adhesion. In this work, a series of copolyimide alkyl ethers containing per fluorinated side-chains were generated to evaluate the influence surface modification agents have on surface chemical, topographical, and mechanical properties. An expanded testing protocol to characterize the adhesion interaction between lunar dust simulant and the copolyimide substrate was carried out. The interfacial adhesion strength was in-situ measured by a custom-built particulate adhesion instrument, utilizing a sonic wand. Surface mechanical properties were characterized by nanoindentation, utilizing the continuous stiffness measurement approach. A nominal presence of surface modifying agents, 1 wt%, resulted in a six-fold reduction in adhesion strength of the interface. A strong inverse correlation between the adhesion strength and Young’s modulus of the substrate was identified. The reduction was attributed to a synergistic interaction between the surface energy, surface roughness, and modulus of the copolyimide alkyl ethers film.

Lunar Dust, Particulate Adhesion, Surface Migratio↗
NASA NTRS2019

Polymer Infused Composite Metal Foam as a Potential Aircraft Leading Edge Material

The leading edge of the aircraft wings must be free from three-dimensional disturbances caused by insect adhesion, ice accretion, and particle wear in order to improve flight performance, safety, and fuel efficiency of the aircraft. An innovative solution was explored in this work by infusing stainless steel composite metal foam (SS CMF) with a hydrophobic epoxy resin system. S-S CMF was made with 100% stainless steel using a powder metallurgy technique. The infused epoxy filled the macro- and microporosities, unique to SS CMF’s structure, creating a product with a density similar to that of aluminum. The contact angle, wear rate, erosion resistance, and insect adhesion of the novel infused composite metal foam were measured and compared to aluminum, epoxy and stainless steel. The infusion process was determined to fill up to 88% of the pores within the SS CMF and was found to reduce wettability and insect residue accretion. The contact angle of the infused SS CMF was 43% higher than its parent material, stainless steel, and 130% higher than aluminum. Insect residue maximum height and areal coverage were reduced by 60 and 30%, respectively, compared to aluminum. Grit blast experiments to simulate erosion resulted in a greater roughness increase for aluminum than for the parent epoxy resin or the resin-infused SS CMF. These results suggest that the durability and performance of infused SS CMF was superior compared to aluminum, which is the current leading edge material of choice. Based on the promising results under relevant wear and erosion conditions, it is concluded that the infused SS CMF can offer a potential tailored replacement to aluminum leading edge material.

Jacob C. Marx↗
NASA NTRS2018

Topological Control of Polystyrene-Silica Core-Shell Microspheres

Controllable surface morphology is requisite across a gamut of processes, industries, and applications. The surface morphology of silica-coated polystyrene microspheres was controllably modified to enable generation of both smooth and bumpy, or raspberry-like, surfaces. Although smooth and raspberry-like silica shells on polystyrene templates have been demonstrated extensively, the method described here used readily available materials to produce radical changes in surface morphology from a single polystyrene template coated in silica through a facile sol-gel reaction processes. Silica shells were deposited via a sol-gel process (using tetraethyl orthosilicate as the silica precursor) onto 1 to 2 m diameter anionic polystyrene spheres, fabricated by emulsifier-free polymerization. By varying of the concentration of silica precursor and ammonium hydroxide catalyst and altering the electrostatic surface interactions via addition of a cationic polymeric brush, an array of surface topologies was generated. The resulting silica shells ranged from 100 to 200 nm in thickness, as measured by calcination of the polystyrene template. Empirical relations between reaction conditions and the resulting silica colloid diameter were utilized to understand the resultant silica shell topology. These results may serve as a guide to generate a versatile platform for research in the multitude of applications where polystyrene-silica core-shell particles are utilized.

Zane A. Grady↗
NASA NTRSDate not supplied

TPSAS-NF1676L-31522-DND

Currently, there are limitations in launch capability regarding requisite payload volume and mass for long duration extra-terrestrial missions. In-space additive manufacturing may provide a solution to this challenge and is applicable for articles ranging from large system and subsystem architectures to small consumables and replacement articles. For small articles, additive manufacturing is becoming more feasible through advances in instrumentation and novel manufacturing strategies capable of generating complex shapes. Many approaches, however, utilize feedstock materials that, once consumed, must be replenished before additional architectures can be generated. Thus, although promising, a major challenge with additive manufacturing is the required starting materials to support on-demand article generation. This presentation describes research toward reversibly assembling materials that can revert to the starting material state for subsequent fabrication. Polyimides were synthesized with thermally reversible Diels-Alder reaction functionalities, furan or maleimide moieties. These materials were characterized utilizing typical spectroscopic, thermal, and mechanical techniques. Amine hardener-enriched epoxy microparticles were synthesized for use as a mechanically robust substrate. Integration of these technologies into a single system and application toward generation of secondary structures on a launch vehicle as a means of in-situ resource utilization will be described.

Christopher J. Wohl↗
NASA NTRSDate not supplied

Bio-inspired Surface Structures to Mitigate Interfacial Particle Adhesion and Erosion - A Review

Lunar dust known as regolith is a huge challenge for lunar exploration missions. Formed over millennia by a complex process involving impacts of meteoroids and micrometeoroids on the lunar surface, lunar dust is porous, highly abrasive with sharp jagged edges, chemically reactive, electrostatically charged and sometimes magnetic. The chemical composition and thickness of the dust layer also varies in different regions of the lunar surface. From samples obtained by previous lunar missions, the average particle size is below 100 microns. This dust has the tendency to strongly adhere to any exposed surfaces, and often degrades the material functionality to eventually cause failure. Any material on the lunar surface is also subject to harsh temperature cycles ranging from -178 ̊C to + 123 ̊C and extreme ultraviolet radiation. While on the lunar surface, different classes of materials would be required for different applications. Advanced materials have been and will be used throughout the lunar lander, habitat, and mission equipment. Examples include: polymeric materials for astronaut protective clothing; metals and ceramics for the lunar lander legs and habitats, and excavating equipment; and semiconductors for solar panels and on-board electronics. In all these applications, the surfaces of the materials are expected or understood to be exposed to the extreme lunar environment condition that includes the regolith dust. During the Apollo missions, the dust clung to and abraded the astronaut’s suits, degraded seals, optics, clogged sensors and reduced performance of thermal radiators. The lunar dust adheres to the surface by various mechanisms, which include electrostatic and Coulombic interactions, Van-der-Waals forces, magnetic forces, mechanical interlocking, chemical bonding and donor-acceptor interactions. There are three primary strategies for developing technologies to minimize the lunar dust adhesion: active, passive and a combination of active and passive. In the active approach, an external energy is needed to prevent or remove particles from collecting on the surface. Mechanically powered brushes and electrodynamic dust screens are two examples. In the passive approach, no external power is needed, and the material surface properties are able to mitigate dust adhesion. A well-known example of this strategy is the low work function coatings for non-stick surfaces. In most cases a combination of active and passive methods might be needed to optimally manage the lunar regolith. The passive method is significantly more attractive as it does not require any external power or an additional control subsystem. These approaches optimize the mission payload and reduce risk. Surface modification to minimize the dust adhesion is thus very important to lunar missions. Here, naturally evolved surface structures might provide guidance for solutions. There are several factors that have to be considered for minimizing particle adhesion to a surface. These include the substrate material properties, surface topography, chemistry, and the characteristics of the adhering particles. When engineering a surface, the substrate material chosen would be dependent on the needs of the application. Tailoring the surface microstructure or chemistry opens up more possibilities for its optimal utilization

Lunar Dust↗
NASA NTRSDate not supplied

Reversibly Assembled Microparticles for Sustained Applications on the Moon and Mars

A sustained presence in any extra-terrestrial environment will require the capability to generate materials, goods, and ultimately vehicles, construction supplies and habitats to be tenable. As an example, NASA, in collaboration with Made In Space, Inc., recently reported the results of extensive research toward enabling3D printing in space. The extensive characterization and comparison of 3D printed articles suggested that, overall, articles generated in the International Space Station microgravity environment were comparable to those generated on Earth. The benefit of in-space manufacturing can be increased through utilization of recyclable materials. A recent analysis of a hypothetical 1,100 day round trip mission to Mars determined that significant mass savings and increase in mission probability of success could be achieved through in-space manufacturing with recyclable materials. NASA’s project ESPUR (Enabling Sustained Presence Using Recyclables), through support from NASA Langley’s Innovative Research and Development Fund, is investigating novel, polymer-coated, epoxy microparticle systems as an enabling technology to realize in-space manufacturing using recyclable feedstocks. Building from previously reported results, further progress toward synthesis of the polymer coating containing click chemical functionalities will be described here. Finite elemental analysis (FEA) has been utilized, in light of scale-free/small world considerations in an effort to identify compositions most likely to yield robust macroscopic geometries. Initial results will be described here. Finally, potential mass savings and life cycle of this recyclable materials technology will be discussed.

Click Chemistry↗
NASA NTRSDate not supplied

Computationally Guided Design of Polymer-Coated Microparticles as Reusable Materials

Long-duration space exploration missions and sustained lunar or Martian surface operations present greater demands for multifunctional and reusable materials. By scaling down the amount of material to be launched from Earth, both mission cost and risk can be reduced. In this regard, leveraging in-space manufacturing capabilities with reusable feedstock materials is an attractive option, as it will allow for articles to be generated on demand, utilized, and then recycled for additional use. NASA’s Enabling Sustained Presence Using Recyclables (ESPUR) project aims to develop reusable materials using polymer-coated microparticles that are bonded via reversible Diels-Alder reactions, where only modest heat is needed to trigger the reverse reaction and enable reuse. For proof-of-concept demonstration, research is currently focused on the fabrication of epoxy microparticles that contain a copoly(carbonate urethane) coating with maleimide and furan functionalities. Here, we discuss the integration of computational materials modeling approaches to help navigate the large design space in this development effort. We perform molecular dynamics (MD) simulations with atomistic and coarse-grained models of the copolymer, which allow us to evaluate the effects of design parameters like the molecular weight and composition on the molecular interactions and chain dynamics. We show how the properties change with the reversible bonds. We also leverage discrete element method (DEM) simulations to assess how microparticle design parameters like the size ratio and volume fraction can be tuned to increase the packing density and number of microparticle contacts to improve the mechanical properties. Our results demonstrate how computational tools can be used in close collaboration with experimental efforts to accelerate material design.

reusable materials↗
NASA NTRSDate not supplied

Laser Angle of Incidence Effects on in-Situ Consolidation of Automated Fiber Placement of Polyaryletherketone Composites

NASA and Electroimpact, Inc. ®†† in conjunction with other U.S. industry partners are performing research as a part of the NASA High-rate Composites for Aircraft Manufacturing (HiCAM) Project to fabricate thermoplastic panels using automated fiber placement (AFP) to increase manufacturing rates of aircraft structural composites. This work focuses on evaluating the in-situ consolidation AFP of thermoplastics (ICAT) process. Previous studies of the ICAT process using semi-crystalline, polyaryletherketone (PAEK) slit-tape have resulted in an adequate degree of intimate contact between plies; however, the resulting interlaminar strength have been less than laminates fabricated in an autoclave. To improve these properties, the effect of reducing the laser angle of incidence (AoI) during placement to increase the degree of auto-hesion was evaluated. The AoI of the laser assisted AFP head was varied between 12° and 16° to fabricate multiple quasi- isotropic and unidirectional test panels. Physics-based thermal models developed at the NASA Langley Research Center were utilized to predict the temperature profile. Laminate processing temperature was measured experimentally, and panel quality was evaluated by both non- destructive evaluation (NDE) as well as destructively by photo-microscopy. The effect on interlaminar strength was determined by short beam strength testing. Test results of carbon fiber laminates fabricated by ICAT using polyetheretherketone (PEEK), polyetherketoneketone (PEKK), and low-melt polyaryletherketone (LM-PAEK) at various laser angles of incidence, placement temperatures and placement speeds are presented.

Laser↗