Search NASA⌕ Search

Engineering topics

Christopher Silva

Publications and source records attributed to Christopher Silva.

16 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Design of a Tiltwing Concept Vehicle for Urban Air Mobility

NASA is establishing a fleet of conceptual air vehicle designs to support research and development for Urban Air Mobility (UAM). This fleet of vehicles will enable examination of the sensitivity of UAM vehicle designs to technology assumptions, identify key research and development needs for UAM aircraft, and provide the UAM community with reference vehicles that are publicly available and based upon known assumptions. To date, four six-passenger reference vehicles have been established: a quadrotor, a side-by-side, a lift-plus-cruise, and a quiet single main rotor helicopter; this paper adds a tiltwing vehicle to the fleet. This paper details the design process that was followed in order to establish the tiltwing vehicle in the fleet, including early conceptual design decisions, sizing and configuration trades, structural analyses, proprotor design and aeroacoustic predictions, and aerodynamic analyses. The resulting tiltwing vehicle uses a turboelectric propulsion system to power six proprotors positioned on a tilting main wing and two tilting proprotors positioned on the horizontal tail. This paper also compares the resulting tiltwing vehicle with the other six-passenger reference vehicles, including an updated lift-plus-cruise vehicle, and then proposes future studies. The fleet of UAM reference vehicles will continue to evolve; subsequent versions of the reference vehicles will be based upon the results of future trade studies and technology developments.

Urban Air Mobility↗
NASA NTRSDate not supplied

XV-15 Tilt Rotor Research Aircraft Photogrammetry and Metrology Measurement

A new measurement capability was created by combining photogrammetry and metrology techniques to accurately measure one half of the XV-15 Tilt Rotor Research Aircraft at the Smithsonian’s Udvar-Hazy museum. The challenges imposed by the fuselage and surrounding environment at Udvar-Hazy were overcome by careful application of photogrammetry and metrology techniques. Data analyses and processing included the use of multiple reverse engineering programs to accurately generate a complete 3-dimensional water-tight geometry of the aircraft and rotor blade. This paper describes the photogrammetry and metrology measurement systems, technology and hardware set-up, data analysis and processing methods, future work, and lessons learned. In addition, selected measurement results of the fuselage and rotor blade are presented.

XV-15↗
NASA NTRSDate not supplied

Mechanical Design of the Urban Air Mobility Side-by-Side Test Stand

The Urban Air Mobility Side-by-Side Test Stand (SBS) is a new capability for the National Aeronautics and Space Administration (NASA) to test the conceptual side-by-side rotorcraft configuration. This test stand enhances the experimental capabilities of the Revolutionary Vertical Lift Technology (RVLT) Project and is primarily designed to be tested in the U.S. Army’s 7-by 10-Foot Wind Tunnel at NASA Ames Research Center. One of the goals for the SBS is to identify the optimal degree of rotor overlap that will yield the best aerodynamic performance. The SBS has two counter-rotating, intermeshing rotors that can vary in lateral separation. The test stand can pitch nose up and nose down, with each rotor having the capability to be trimmed independently through cyclic and collective controls. Six-axis load cells and rotary torque sensors are placed underneath each rotor to measure the thrust, torque, and side force from each rotor system. This paper describes the mechanical design of the SBS and outlines the structural analyses conducted to ensure a safety factor of 4 for ultimate strength and 3 for yield strength during all experimental testing.

Mechanical Design↗
NASA NTRSDate not supplied

Practical Conceptual Design of Quieter Urban VTOL Aircraft

A toolchain and process for conceptual design of VTOL rotorcraft, employing low- and mid-fidelity tools is presented. The approach is capable of providing more quantitatively-credible trades between noise, size, and cost metrics than the methods commonly used for conceptual design. In addition to a general conceptual design tool, the approach employs comprehensive analysis for trim, blade motion, and airloads; these are then used by acoustic analysis software to develop source sound, propagate it, and calculate noise metrics. A key aspect of the approach is flexibility to assess varied aircraft types and different technologies and design features. Vehicles are sized using a representative Urban Air Mobility design mission. Demonstration cases are presented for a single main rotor helicopter, quadrotor, side-by-side helicopter, and lift+cruise aircraft. Noise metrics used for demonstration are the FAA/EASA certification Effective Perceived Noise Levels for takeoff, flyover, and approach. The concept aircraft in this study are shown to achieve reductions in noise relative the initial design points, with changes in mission performance and cost as a consequence. Many of the designs are predicted to be tens of EPNdB quieter in the certification metrics than existing helicopters.

Conceptual Design↗
NASA NTRSDate not supplied

Prediction of Quadrotor Acoustics Using RVLT Toolchain

The NASA Revolutionary Vertical Lift Technology (RVLT) Project toolchain is used to predict the acoustics of the NASA 6-passenger quadrotor concept vehicle. A qualitative study of the blade vertical loading to understand noise trends with tip speed and number of blades was performed. Trends of the individual rotor noise sources (thickness, loading, and broadband) are studied. Noise is predicted and analyzed for three flight conditions: approach (6-deg descent), level flight flyover, and takeoff. Three quadrotor designs are considered: tip speed=700 ft/sec, 3 blades (“700/3”), “550/3”, and “375/7”. The qualitative study shows that during approach multiple, strong BVIs occur on the advancing and retreating sides for “700/3” and “550/3”, but for “375/7” only weak BVIs are present. Consistent with this BVI scenario, the quadrotor noise results show that “700/3” has the highest loading noise (and EPNL) and “375/7” the lowest loading noise (and EPNL), with “550/3” falling in between. Broadband noise during approach and flyover is roughly the same for all three designs. Takeoff broadband noise is much lower, especially for “375/7”. The bulk of the results have been obtained with a rigid uniform blade model, with a flap hinge and a pitch bearing. For “550/3”, noise predictions with elastic nonuniform blades have been initiated and are ongoing.

Quadrotor↗
NASA NTRSDate not supplied

A Data-Driven Reduced Order Model of an Isolated Rotor

There are numerous conceptual design stage rotorcraft analysis tasks which demand a high-fidelity and low cost method for rotor load distribution predictions. Considering Urban Air Mobility (UAM) vehicles aim to operate in close proximity to buildings and with unique rotor configurations, there is a significant challenge in quickly and accurately modeling rotors operating in complex, turbulent flow fields. One potential path for deriving a high-fidelity, low cost rotor model is with data-driven surrogate modeling. In this study, an initial investigation is taken to apply a proper orthogonal decomposition (POD) based reduced order model (ROM) for the purpose of pressure distribution prediction. In this study, a POD ROM was derived to produce distributed pressure predictions on rotor blades subjected to topology change due to variation in twist and taper ratio. Rotor twist was varied between 0◦, 10◦, 20◦, and 30◦ while taper ratio was varied between 1.0, 0.9, 0.8, and 0.7. All rotors consisted of a single blade. The POD ROM was validated for three demonstration cases; a high thrust rotor in hover, a low thrust rotor in hover, and a rotor in forward flight with a flight speed of M = 0.1. Results showed highly accurate distributed load predictions could be achieved at minimal computational cost. Computational cost for hovering blade surface pressure modeling was reduced from 12 hours on 440 cores to 10−5 seconds on a single core. For blade in forward flight cost was reduced from 20 hours on 440 cores to 0.6 seconds on a single core. For cases of high thrust and low thrust rotors, POD ROM was used to undergo a design optimization of the rotor such that figure of merit was maximized. Total optimization time for each case was 1 minute.

Data-Driven↗
NASA NTRSDate not supplied

Aeroservoelastic Flight Dynamic Modeling of UAM Conceptual Vehicles

This paper presents an aeroservoelastic flight dynamic modeling approach for NASA Lift+Cruise eVTOL aircraft in forward flight. A conceptual aerodynamic analysis for forward flight is performed in CHARM, a rotorcraft aeromechanics unsteady vortex-lattice flow solver. A trim analysis is performed to obtain the steady state aerodynamic information at a trim point to be used for the aeroelastic analysis. A NASTRAN finite element model for the Lift+Cruise vehicle is available. The structural dynamic mode shapes are extracted from the NASTRAN for the aeroelastic analysis. An aeroservoelastic model is developed using the Theodorsen’s theory. A stability and control derivative analysis is performed to formulate a flight dynamic model of the Lift+Cruise vehicle. An aeroservoelastic flight dynamic model is formulated by coupling these two models together. Flight dynamic and flutter analyses are performed to determine vehicle stability and flutter-free operation.

Aeroservoelasticity↗
NASA NTRSDate not supplied

Effect of Rotor Blade Elasticity on UAM Quadrotor Acoustics

The 6-passenger quadrotor concept vehicle designed under the NASA Revolutionary Vertical Lift Technology (RVLT) Project is considered for acoustic analysis. The tip speed is 550 ft/sec, with three blades per rotor (550/3). Originally, the blades were rigid, uniform spanwise, and with flap and pitch degrees of freedom. The blade model has since been updated: a lag hinge was added, and nonuniformities and elastic properties were introduced. Four blade models are considered: 1) original model, rigid uniform flap-pitch; 2) rigid uniform flap-lag-pitch; 3) rigid nonuniform flap-lag-pitch; and 4) elastic nonuniform flap-lag-torsion. Predictions are made for three flight conditions (approach, flyover, and takeoff) using the four blade models. The RVLT Toolchain is exercised using CAMRAD II and pyaaron/AARON/ANOPP2. Quadrotor trim and performance, 0.75R vertical blade loading for all four rotors, and noise sources are analyzed. Also, the contributions of the front and rear rotor pairs to noise are studied. In approach and flyover, a 2 dBA loading noise difference (delta) is predicted between blade models 1 and 4 (delta for takeoff is smaller, 1 dBA). Most of this noise delta is due to the lag hinge and nonuniformities, which is consistent with the results of a 2022 study that had considered only the approach condition; the current results extend this conclusion to flyover and takeoff also. The insensitivity of quadrotor noise to blade elasticity is currently attributed to the high blade torsional stiffness (frequency 6.41 per rev) and the small blade radius (9 ft) of the 550/3 design. Suggestions for potential follow-on work are given.

Rotor Blade↗
NASA NTRSDate not supplied

Enhanced Flight Dynamics Models with Aerodynamic Interference for Real-Time Simulation of VTOL Concept Vehicles

In an effort to establish common models to support the Advanced Air Mobility (AAM) community, NASA has designed a fleet of VTOL configuration reference models. Advanced Rotorcraft Technologies (ART) in cooperation with the NASA Ames Aeromechanics branch has developed FLIGHTLAB simulation models for several of these AAM VTOL concept vehicles. These simulation models are real-time capable while maintaining accurate flight dynamic characteristics with enhanced interference simulation by extracting important modeling parameters from Viscous Vortex Particle Method (VVPM). The focus of this paper is threefold. First, it introduces the simulation models developed and describes their modeling characteristics important to control and flight dynamics simulation. Second, the method for deriving the interference coefficients between model components such as rotors and wings is outlined. Implementation of the method for the lift+cruise and tiltwing models are discussed in detail. Third, the accuracy of the interference enhancement is assessed, with emphasis placed on the impacts to trim and flight dynamic characteristics. The interference enhancement method is further used to evaluate configuration design decisions by quantifying performance aspects of interference. This research effort culminated in simulation models for the AAM VTOL concept vehicles, with proper interference and real-time capability.

Flight Dynamics↗
NASA NTRSDate not supplied

Applicability of Fly Neighborly Noise Recommendations to UAM Quadrotors Undergoing Steady Maneuvers

This initial study examines whether the Helicopter Association International (HAI) Fly Neighborly operational recommendations that are based on single main rotor/tail rotor configurations will hold for non-conventional UAM rotorcraft with multiple rotors. The 6-occupant quadrotor concept vehicle designed under the NASA Revolutionary Vertical Lift Technology (RVLT) Project is studied. The tip speed is 550 ft/sec, with three blades per rotor (“550/3”). Predictions are made for three steady maneuvers: level turns, descending turns, and climbing turns. The RVLT Toolchain is exercised using CAMRAD II, pyaaron/AARON/ANOPP2 and a beta version of AMAT (ANOPP2 Mission Analysis Tool). AMAT provides functionality to acoustically model the curved flight paths associated with maneuvers. In addition to quadrotor trim and performance, this study includes analysis of azimuthal variations of the vertical blade loading and its derivative in the form of contour plots on a rotor plane and line plots at one radial location (r/R=0.765). Quadrotor noise trends are analyzed using maximum Overall Sound Pressure Level (OASPL) and Effective Perceived Noise Level (EPNL). The Fly Neighborly guideline that addresses descents (“Level turns are quieter than descending turns”) is predicted to hold for the RVLT Quadrotor as well.

UAM↗
NASA NTRSDate not supplied

Enhancements, Verification, and VMS Integration of VTOL Concept Vehicle Simulation Models

Advanced Rotorcraft Technology (ART) and the NASA Ames Aeromechanics branch have jointly developed FLIGHTLAB simulation models for Advanced Air Mobility (AAM) VTOL concept vehicles. The overarching purpose of the simulation model development is to establish a set of well defined reference vehicles for FLIGHTLAB users and the rotorcraft community. The ongoing research effort and enhancement of these AAM simulation models to fulfill the role of quality reference vehicles is this paper’s focus. The content of this paper expands on the established characteristics of these AAM models in three primary areas. First, enhancement of the lift+cruise and tiltwing models with elastic airframe properties is discussed. The process of setting up the elastic airframe model in FLIGHTLAB, as well as the impacts on flight characteristics are explained. The introduction of the elastic airframe modeling allows these models to be used in flight dynamics, loads, and vibration analysis of the configuration designs. Next, linear model generation from the enhanced simulation model is covered. Confirming the validity of the linearized models is of importance, as these linear models are utilized for flight control design and tuning for these experimental configurations. For the final focus, the progress towards implementation of these models into the NASA Ames Vertical Motion Simulator (VMS) is described. This task seeks to demonstrate the procedures of integrating a FLIGHTLAB flight simulation in the VMS environment, test fully integrated simulation with communication between flight dynamics, control, and propulsion models, and explore the essential aspects of simulation model integration in a full flight simulator environment. This includes I/O definition, initialization, trim, flying, etc. By expanding the capabilities of the AAM simulation models, they continue to develop as valuable and approachable modeling references.

VMS↗
NASA NTRSDate not supplied

Flight Dynamics Conceptual Design Exploration of Multirotor eVTOL

The advent of electric propulsion is revolutionizing the paradigm of rotorcraft design, leading to new electric Vertical Take-Off and Landing (eVTOL) aircraft. Direct drive topologies are common within these new designs, and some designers have chosen to utilize this mechanism for Primary Flight Control (PFC), effectively utilizing the aircraft engines as PFC actuators to control the speed of the rotors. This decision integrates the propulsion and flight control systems, and intrinsically couples the aircraft sizing and control. Four separate tools were exercised throughout this study to conduct a conceptual design exploration of eVTOL aircraft handling qualities. The main tasks for these tools were: 1) aircraft sizing and performance analysis, including the calculation of trim; 2) flight dynamics modeling and analysis; 3) handling qualities-centric control law optimization; and 4) electric motor sizing. Sizing of an RPM- controlled Hexacopter concept explored the dependency of aircraft size to fundamental design parameters: 1) disk loading and 2) blade loading coefficient. Increasing the design disk loading resulted in designs with high agility, but at the cost of significant growth in the design gross weight. Finally, Categories II and III pilot-induced-oscillation (PIO) are known potentially-catastrophic handling qualities deficiencies of fly-by-wire flight control systems such as those expected of eVTOL aircraft. Consideration of PIO predictive metrics in conceptual design control synthesis led to increased PIO robustness.

Flight Dynamics↗
NASA NTRSDate not supplied

Aircraft Design Implications for Urban Air Mobility Vehicles Performing Public Good Missions

NASA has previously designed and described set of concept aircraft to serve as reference vehicles for Urban Air Mobility (UAM), to encourage public discussion and research. These vehicles are used in this paper to quantify how suitable UAM aircraft might be for missions other than their primary commercial design missions. A set of representative public good missions are described, along with design requirements and equipage. For two of these missions, the additional weight, power, and cost to facilitate a basic vehicle which may be built or configured with the ability to perform these missions is quantified. Special layout and other considerations which may impact vehicle design are described. For aircraft designed to the NASA UAM reference mission, the addition of some meaningful public good missions causes less than 10% growth in weight and power for fossil-fueled aircraft; advanced batteryelectric powered aircraft grow by a significantly larger amount and may only be possible with relaxed requirements. Meaningful public good missions with UAM vehicles are feasible, provided that public good mission requirements are considered and incorporated in the conceptual design stage of development.

Aircraft↗
NASA NTRSDate not supplied

Design of a Six-Tiltrotor Concept Vehicle for Urban Air Mobility

NASA has developed a series of aircraft concepts known as reference vehicles for urban air mobility operations to facilitate research and development, enabling system-level comparisons between design candidates. In this study, new six-tiltrotor reference vehicles with full-electric and turboelectric propulsion systems were developed using the NASA Design and Analysis of Rotorcraft (NDARC) tool. The sizing results and performance metrics of these new vehicles are presented, along with comparisons to existing reference vehicles. The turboelectric six-tiltrotor is shown to be the fastest among the turboelectric reference vehicles. Although the full-electric six-tiltrotor is not as fast as the turboelectric version, it still offers considerable speed along with increased safety compared to the tiltrotor reference vehicle.

Six-Tiltrotor↗
NASA NTRSDate not supplied

Impact of Technology and Mission Variations on Aircraft Designed for Advanced Air Mobiity

NASA is conducting investigations in Advanced Air Mobility (AAM) aircraft and operations, including the development of Urban Air Mobility (UAM) aircraft designs that can be used to focus and guide research activities in support of AAM. This report is an investigation of the impact of technology and mission variations on several of the NASA AAM concept aircraft: quadrotor, quiet single main rotor, side-by-side, and tiltrotor configurations, with turboshaft and electric propulsion variants for each. First, the mission and aircraft models of the baseline designs were reassessed and updated, including rotor geometry optimization, update of the rotor performance models, and disk loading optimization. For these eight designs, technology and mission excursions were performed. Relative to the calibration cases that can be considered examples of good design practice, the impact of the weight technology factors is significant. For the electric aircraft, there is a very large impact of battery specific energy (Wh/kg), and correspondingly a very large impact of mission range. The vision of Advanced Air Mobility is driven by missions that will enable new transportation capabilities. Hence it is appropriate to compare Concept Vehicles of different lift and propulsive architectures, all designed to accomplish the same UAM mission. It is also useful however to consider specific missions that can take advantage of the strengths of individual aircraft configurations. So alternate designs were also developed for the concept vehicles: for turboshaft aircraft, longer unrefueled range, including faster cruise speed for the tiltrotor; for electric aircraft, shorter range and more realistic battery weight.

Technology↗