Search NASA⌕ Search

Engineering topics

Chrobak, C. P.

Publications and source records attributed to Chrobak, C. P..

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Modeling of ExB effects on tungsten re-deposition and transport in the DIII-D divertor

Mixed-material DIVIMP-WallDYN modelling, now incorporating ExB drifts, is presented that simultaneously reproduces tungsten (W) erosion and deposition patterns observed during the DIII-D Metal Rings Campaign, in which a toroidally symmetric set of W-coated tiles were installed in the carbon (C) DIII-D divertor. Since most reactor plasma facing component (PFC) designs call for mixed-material environments, including ITER’s W/Be enviroment, the divertor targets will quickly evolve into reconstitued surfaces of multiple elements. This work identifies controlling physics that affects material migration patterns in the divertor, which impact PFC lifetimes and impurity leakage from the divertor to the core. These simulations indicate that radial and poloidal ExB transport dominates over parallel force balance for high-Z impurities such as W in the divertor region of DIII-D. It is demonstrated that ExB drifts are required to reproduce the experimental observation of non-local W and C co-accumulation in a band ~7-9 cm outboard of the outer-strike-point (OSP) W source, for attached Lmode conditions in the unfavorable ion grad-B drift direction. In addition, W gross erosion is localized to the region outboard of the OSP, as the formation of C co-deposits suppresses W erosion at the strike point. Time-dependent simulations with scaled ExB impurity drifts (60% of the OEDGE-calculated drift velocity) and W re-erosion quantitatively reproduce these features, including depth-resolved W/C ratios, within a factor of 2 over ~115 seconds of accumulated plasma exposure. The location of co-deposition regions is shown to be well represented by an analytic leakage model, driven largely by poloidal ExB drifts. Qualitative agreement is also found between campaign-integrated W deposition measurements and simulations for the favorable ion grad-B drift direction, the standard mode of operation for most tokamaks. Furthermore, these results imply that a longterm inward radial migration of material from the outer divertor through the private flux region may occur in future devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Impact of divertor material on neutral recycling and discharge fueling in DIII-D

We report that experiments with the lower divertor of DIII-D during the Metal Rings Campaign (MRC) show that the fraction F of atomic D in the total recycling flux is material-dependent and varies through the ELM cycle, which may affect divertor fueling. Between ELMs, F C ~ 10% and FW ~ 40%, consistent with expectations if all atomic recycling is due to reflections. During ELMs, F C increases to 50% and F W to 60%. In contrast, the total D recycling coefficient including atoms and molecules R stays close to unity near the strike point where the surface is saturated with D. During ELMs, R can deviate from unity, increasing during high energy ELM-ion deposition (net D release) and decreasing at the end of the ELM which leads to ability of the target to trap the ELM-deposited D. The increase of R > 1 in response to an increase in ion impact energy Ei has been studied with small divertor target samples using Divertor Materials Evaluation System (DiMES). An electrostatic bias was applied to DiMES to change E i by 90 eV. On all studied materials including C, Mo, uncoated and W-coated TZM (>99% Mo, Ti, and Zr alloy), W, and W fuzz, an increase of E i transiently increased the D yield (and R) by ~10%. On C there was also an increase in the molecular D 2 yield, probably due to ion-induced D 2 desorption. Despite the measured increase in F on W compared to C, attached H-mode shots with OSP on W during MRC did not demonstrate a higher pedestal density. About 8% increase in the edge density could be seen only in attached L-mode scenarios. The difference can be explained by higher D trapping in the divertor and lower divertor fueling efficiency in H- versus L-mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Localized divertor leakage measurements using isotopic tungsten sources during edge-localized mode-y H-mode discharges on DIII-D

Experiments carried out on DIII-D using a novel setup of isotopic tungsten (W) sources in the outer divertor have characterized how the W leakage from this region depends on both the exact source location and edge-localized mode (ELM) behavior. The sources are toroidally-symmetric and poloidally-localized to two regions: (1) the outer strike point (OSP) with natural abundance of W isotopes; and (2) the far-target with highly-enriched 182 W isotopes. With the use of a dual-faced collector probe (CP) in the main scrape-off layer (SOL) near the outside midplane and source-rate spectroscopy, a proxy for divertor impurity leakage is developed herein. Using this proxy, it is found that for the OSP W location, there is a nearly linear increase of leakage with the power across the separatrix ( ), which is consistent with the effect of an increased upstream ion temperature parallel gradient force in the near-SOL; trends in the pedestal density and collisionality are also seen. Conversely, it is found that for the far-target W location leakage falls off rapidly as increases and ELM size decreases, which is suggestive that ELM size plays a role in the leakage from this location. Indications for main SOL W contamination is evidenced by the measurement of large deposition asymmetries on the two opposite CP faces. These measurements are coupled with interpretive modeling showing SOL W accumulation near the separatrix furthest from both targets driven by forces parallel to the magnetic field. This experimental setup, together with the target and upstream W measurements, provides information on the transport from different divertor W source locations and leakage. These studies help to elucidate the physics driving divertor impurity source rates and leakage, with and without ELMs, and provide better insight on the link in the chain connecting wall impurity sources to core impurity levels in magnetic fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Elemental and topographical imaging of microscopic variations in deposition on NSTX-U and DIII-D samples2

Abstract: Tokamak plasma facing components have surface roughness that can cause microscopic spatial variations in erosion and deposition and hence influence material migration, erosion lifetime, dust and tritium accumulation, and plasma contamination. However high spatial resolution measurements of deposition on the scale of the surface roughness have been lacking to date. We will present elemental images of graphite samples from NSTX-U and DIII-D DiMES experiments performed with a Scanning Auger Microprobe at sub-micron resolution that show strong microscopic variations in deposition and correlate this with 3D topographical maps of surface irregularities. The NSTX-U samples were boronized and exposed to deuterium plasmas and the DiMES samples had localized Al and W films and were exposed to dedicated helium plasmas. Topographical maps of the samples were performed with a 3D confocal optical microscope and compared to the elemental deposition pattern. The results revealed localized deposition concentrated in areas shadowed from the ion flux, incident in a direction calculated (for the DiMES case) by taking account of the magnetic pre-sheath.

Erosion, Deposition, NSTX-U, DIMES, Plasma-Materia↗