Engineering topics
Chuang, Andrew Chihpin
Publications and source records attributed to Chuang, Andrew Chihpin.
In situ synchrotron X-ray diffraction analysis of ultrasonically assisted microstructure refinement during laser melting process
This work investigates the effect of ultrasonic treatment (UST) on the microstructure of AA4043 alloy during laser melting process. Here, the study utilizes in situ synchrotron X-ray diffraction (SXRD) and postmortem electron backscatter diffraction (EBSD) techniques to examine the ultrasonic grain refinement mechanism. The SXRD diffraction patterns exhibit higher continuity of major diffraction rings in the UST-test pattern, indicating a more refined grain structure. The presence of new diffraction spots in the post-test diffraction pattern with UST suggests the breakdown of epitaxial growth of columnar dendrites during solidification. Thermal profiles determined by analyzing the lattice parameter evolution show a faster cooling rate with UST. The inverse pole figures and aspect ratio distribution from EBSD reveal that the UST samples exhibit a refined, more equiaxed grain structure along the weld centerline. UST sample also develops more fine-sized low angle grain boundaries (LAGBs). These features offer better hot-cracking resistance in aluminum alloys.
Mechanisms for high creep resistance in alumina forming austenitic (AFA) alloys
Castable alumina forming austenitic (AFA) alloys have demonstrated superior creep life and oxidation resistance at temperatures exceeding 800⁰C. Despite the success in the applicability of these alloys in extreme environments, there is a limited understanding of the deformation modes and the influence of each alloying element guiding the alloy design strategies that could further enhance the creep strength of these AFA alloys, particularly at temperatures at and above 900⁰C. In this study, we reveal the mechanism underpinning the superior creep performance of castable AFA alloys that involves suppressing primary carbide formation through minor compositional modification. This approach results in a three-fold increase in creep strength at 900⁰C and 50 MPa. Here, by employing integrated characterization techniques, we analyzed the microstructures of two AFA alloys, both before and after the creep process. We discovered that the suppression of primary carbides permits the in-situ clustering of now-available interstitial elements such as C, Si, and O during high-temperature creep. This improved solid solution strengthening and reduced stacking fault energy of the alloy. Moreover, it also enabled controlled secondary carbide formation during testing, further improving the creep resistance. These findings underline the important interplay between alloy composition, microstructure, and creep properties, and offer a promising design strategy for developing economical high-temperature Fe-based alloys suitable for advanced applications.
Synchrotron X-ray diffraction analysis of constituent phases in transition joint between nickel alloy 738LC and a MnFeCoNiCu alloy
Synchrotron x-ray diffraction (XRD) analysis was performed on transition joints between a single-phase MnFeCoNiCu alloy and Ni-base Alloy 738LC to efficiently identify the constituent phases across the interface, with different levels of material intermixing generated by laser-welding with variable power. Here, the intermixing extent was quantified by postmortem energy dispersive x-ray spectroscopy mapping. Diffraction-based analyses on complex composition spaces with limited prior data present significant challenges because elemental substitution in both disordered and ordered phases is more extensive than in conventional alloy spaces, which may effectuate relatively large shifts in the observed lattice parameters that convolute the analysis. Therefore, thermodynamic simulations and crystallographic literature data were employed to construct a system-specific diffraction library of twelve prospective phases for the composition space investigated. Subsequently, for predicted disordered cubic phases, statistical hard-sphere models were established to estimate the lattice parameters and predict diffraction peak positions for inclusion in the library. The library was then employed to analyze diffraction profiles measured from the variably intermixed transition joints, with focus on accounting for both high and low-intensity peaks. 99.0 % of diffraction peaks with relative intensity greater than 0.001 were assigned to phases from the system-specific library, exemplifying rigorous peak accounting and indicating that no unexpected phases were present. Up to six of the twelve library phases were experimentally found in the transition joints. The lattice parameters predicted by the statistical hard-sphere model based upon thermodynamic simulations agree reasonably well with the measured values for the disordered FCC matrix phase.
Atomic faulting induced exceptional cryogenic strain hardening in gradient cell–structured alloy
Coarse-grained materials are widely accepted to display the highest strain hardening and the best tensile ductility. We experimentally report an attractive strain hardening rate throughout the deformation stage at 77 kelvin in a stable single-phase alloy with gradient dislocation cells that even surpasses its coarse-grained counterparts. Contrary to conventional understanding, the exceptional strain hardening arises from a distinctive dynamic structural refinement mechanism facilitated by the emission and motion of massive multiorientational tiny stacking faults (planar defects), which are fundamentally distinct from the traditional linear dislocation–mediated deformation. In conclusion, the dominance of atomic-scale planar deformation faulting in plastic deformation introduces a different approach for strengthening and hardening metallic materials, offering promising properties and potential applications.
Solidification modes during additive manufacturing of steel revealed by high-speed X-ray diffraction
Solidification during fusion-based additive manufacturing (AM) is characterized by high solidification velocities and large thermal gradients, two factors that control the solidification mode of metals and alloys. Using two synchrotron-based, in situ setups, we perform high-speed X-ray diffraction measurements to investigate the impact of the solidification velocities and thermal gradients on the solidification mode of a hot-work tool steel over a wide range of thermal conditions of relevance to AM of metals. The solidification mode of primary δ-ferrite is observed at a cooling rate of 2.12x10 4 K/s, and at a higher cooling rate of 1.5x10 6 K/s, δ-ferrite is sup-pressed, and primary austenite is observed. The experimental thermal conditions are evaluated and linked to a Kurz-Giovanola-Trivedi (KGT) based solidification model. The modelling results show that the predictions from the multicomponent KGT model agree with the experimental observations. This work highlights the role of in situ XRD measurements for a fundamental understanding of the microstructure evolution during AM and for vali-dation of computational thermodynamics and kinetics models, facilitating parameter and alloy development for AM processes.
Influence of oxygen on performance of multi-principal element alloy as braze filler for Ni-base alloys
In manufacturing of multi-principal element alloys (MPEAs), the casting process is often a primary point of oxygen introduction to the material system, which was demonstrated by the laboratory scale button arc-melting process. Oxygen introduction raises concerns for the mechanical performance of these alloys if employed as structural materials alone or in engineering applications, such as serving as filler materials to enable joining of similar or dissimilar alloy pairs that are conventionally considered difficult to join. In this work, oxide inclusions in an as-cast off-equiatomic MnFeCoNiCu MPEA and Ni-base alloy braze joints made with this MPEA were evaluated by synchrotron x-ray diffraction mapping and electron microscopy. MnO was found to be prevalent throughout the cast MPEA and was chemically reduced during brazing by trace Al from the base material, Ni-base Alloy 600. Incomplete reaction of the MnO with Al, and some alternative reaction with Cr, left a mixture of MnO, Al 2 O 3 , and Cr 2 O 3 in the as-brazed joint, with the oxides concentrated near the braze centerline due to directional solidification. Further, in the braze joints, the non-oxide constituent phases detected were an FCC matrix and particles of Cr 23 C 6 , Cr 7 C 3 , and TiN which are all native to Alloy 600. The evolution of oxides within the brazed joints at elevated service temperatures of 600-800°C was also evaluated. While MnO and Al 2 O 3 were stable during high-temperature service, Cr 2 O 3 particles grew to several hundred microns, with dissolved oxygen in the MPEA providing a significant source for oxide growth. Comparing tensile performance of the as-brazed condition with post-service conditions showed that the evolution of oxide particles contributed to an increase in strength and decrease in ductility of the brazed joints. Evaluating particle morphologies among fracture surfaces of individual specimens demonstrated that large Cr 2 O 3 particles and continuous cluster networks of Al 2 O 3 were the features most detrimental to total elongation. Hence, unmitigated evolution of oxygen-containing species during brazing and service conditions is detrimental to the ductility of the brazed joints, which highlights the importance of oxygen control in initial manufacturing of MPEAs for engineering applications.
Discharge intermittency considerably changes ZnO spatial distribution in porous Zn anodes
Porous Zn anodes are ubiquitous in primary batteries and are under development for low-cost rechargeable batteries. Spatial distribution of ZnO discharge product is a critical factor in these, because it can passivate the active material. In rechargeable cells this is related to a major failure mechanism called shape change, in which ZnO is relocated to inactive locations. In this work we demonstrate rest steps during discharge of primary Zn anodes dramatically alter the placement of ZnO in the anode. In alkaline electrolyte, ZnO discharge product is typically modeled as precipitating close to Zn particles, forming a porous ZnO shell around the Zn core. Further, anodes discharged continuously at low-rate are compared to anodes similarly discharged intermittently, using in situ computed tomography from a synchrotron source. Zn–ZnO core-shell structures are produced during continuous discharge but are not found in cells discharged intermittently. Continuously discharged cells showed that ZnO was formed most strongly near the separator, in agreement with Zn anode battery models. In pulse-discharged cells, ZnO was more radially distributed and was in large formations not physically connected to Zn particles. Thus, discharge intermittency changes spatial distribution of ZnO in ways that are unpredicted by Zn anode models.
Structural changes across thermodynamic maxima in supercooled liquid tellurium: a water-like scenario
Liquid polymorphism is an intriguing phenomenon which has been found in a few single-component systems, the most famous being water. By supercooling liquid Te to more than 130 K below its melting point and performing simultaneous small-angle and wide-angle X-ray scattering measurements, we observe clear maxima in its thermodynamic response functions around 615 K, suggesting the possible existence of liquid polymorphism. A close look at the underlying structural evolution shows the development of intermediate-range order upon cooling, most strongly around the thermodynamic maxima, which we attribute to bond-orientational ordering. The striking similarities between our results and those of water, despite the lack of hydrogen-bonding and tetrahedrality in tellurium, indicate that water-like anomalies may be a general phenomenon among liquid systems with competing bond- and density-ordering.
Novel processing route for design and manufacturing of metal toughened nanoceramics: Al–Al 2 O 3 nanocermets
Monolithic alumina is a highly brittle ceramic with a very low fracture toughness, making it an unreliable material for mechanical and structural applications. Ceramic-metal composites (cermets) are the subject of intensive interest to obtain materials which can address the intrinsic brittleness of ceramics without compromising their high strength and light weight. In the present investigation, aluminium-alumina (Al–Al 2 O 3 ) nanocermets were developed. The nanocermets possessed the toughness of Al phase and the strength of reinforced nano Al 2 O 3 particles. Here, the nanocermets green bodies were prepared such that upon sintering each adjacent Al 2 O 3 grain was conformally coated with a continuous Al film. Mechanical milling via a combination of cryo-milling and ball-milling was used to prepare Al–Al 2 O 3 nano-powder mixture. Spark plasma sintering was used to consolidate the green nanocermets. Results show that specimens prepared from 35 h milled powders exhibited superior mechanical properties as compared to other nanocermets, with an improvement in microhardness, elastic modulus, compressive strength, and flexural strength by 88%, 78%, 69% and 40% with respect to sintered pure Al. The indentation toughness of 35 h milled nanocermet showed an increment of 12.5% with respect to sintered pure Al 2 O 3 . Characterization techniques such as XRD, SEM, HR-TEM, X-ray tomography were employed to investigate the phase evolution and structural morphology, while FEM simulations were performed for understanding the crack propagation mechanisms in nanocermets.
Defect and satellite characteristics of additive manufacturing metal powders
Metal additive manufacturing (AM) requires high-quality metal powders to three-dimensionally (3D) print metallic components with complex and customizable geometries. The lack of quantification of AM metal powders creates quality control challenges for 3D printed components, increases the uncertainty of printing reliability and net cost of inspected and certified printed components, and reduces the recyclability of used powders. However, critical characteristics of AM metal powders that are decisive factors for the 3D printing process, such as internal porosity, contamination, and satellite feature, remain ambiguous. In this work, we developed a novel approach to 3D quantify key characteristics of AM metal powders down to individual particles by using high-resolution synchrotron x-ray computed tomography. Empowered by the penetrative capability of high-energy x-ray, internal porosity and contamination within as-atomized metal powders from high-entropy alloys to nickel-based superalloys were evaluated. Additionally, the newly-developed dispersion method enables the homogeneous separation of individual particles, and consequently, results in the implementation of 3D particle shape analysis. To resolve a major challenge of identification and quantification of satellite-feature particles in as-atomized AM metal powders, the satellite features were quantitated by modeling and analyzing the shape parameter of local thickness variance. Furthermore, the 3D analytical methods of particle assessment in this study can be applied to other materials systems like rock, food, and pharmaceutical particles, and provide insights for process optimization across powder metallurgy, concrete, food and pharmaceutical manufacturing, and AM industries.
Effect of crystallite geometries on electrochemical performance of porous intercalation electrodes by multiscale operando investigation
Lithium-ion batteries are yet to realize their full promise because of challenges in the design and construction of electrode architectures that allow for their entire interior volumes to be reversibly accessible for ion storage. Electrodes constructed from the same material and with the same specifications, which differ only in terms of dimensions and geometries of the constituent particles, can show surprising differences in polarization, stress accumulation and capacity fade. Here, using operando synchrotron X-ray diffraction and energy dispersive X-ray diffraction (EDXRD), we probe the mechanistic origins of the remarkable particle geometry-dependent modification of lithiation-induced phase transformations in V2O5 as a model phase-transforming cathode. A pronounced modulation of phase coexistence regimes is observed as a function of particle geometry. Specifically, a metastable phase is stabilized for nanometre-sized spherical V2O5 particles, to circumvent the formation of large misfit strains. Spatially resolved EDXRD measurements demonstrate that particle geometries strongly modify the tortuosity of the porous cathode architecture. Greater ion-transport limitations in electrode architectures comprising micrometre-sized platelets result in considerable lithiation heterogeneities across the thickness of the electrode. These insights establish particle geometry-dependent modification of metastable phase regimes and electrode tortuosity as key design principles for realizing the promise of intercalation cathodes. Designing electrode architectures for Li-ion batteries that can be reversibly accessible for ion storage can be challenging. Using operando techniques the mechanistic origin of lithiation-induced phase transformations in a V2O5 model cathode is now clarified.
Gradient cell–structured high-entropy alloy with exceptional strength and ductility
We report that similar to conventional materials, most multicomponent high-entropy alloys (HEAs) lose ductility as they gain strength. In this study, we controllably introduced gradient nanoscaled dislocation cell structures in a stable single-phase HEA with face-centered cubic structure, thus resulting in enhanced strength without apparent loss of ductility. Upon application of strain, the sample-level structural gradient induces progressive formation of a high density of tiny stacking faults (SFs) and twins, nucleating from abundant low-angle dislocation cells. Furthermore, the SF-induced plasticity and the resultant refined structures, coupled with intensively accumulated dislocations, contribute to plasticity, increased strength, and work hardening. These findings offer a promising paradigm for tailoring properties with gradient dislocation cells at the nanoscale and advance our fundamental understanding of the intrinsic deformation behavior of HEAs.
In situ synchrotron diffraction and modeling of non-equilibrium solidification of a MnFeCoNiCu alloy
The solidification mechanism and segregation behavior of laser-melted Mn 35 Fe 5 Co 20 Ni 20 Cu 20 was firstly investigated via in situ synchrotron x-ray diffraction at millisecond temporal resolution. The transient composition evolution of the random solid solution during sequential solidification of dendritic and interdendritic regions complicates the analysis of synchrotron diffraction data via any single conventional tool, such as Rietveld refinement. Therefore, a novel approach combining a hard-sphere approximation model, thermodynamic simulation, thermal expansion measurement and microstructural characterization was developed to assist in a fundamental understanding of the evolution of local composition, lattice parameter, and dendrite volume fraction corresponding to the diffraction data. This methodology yields self-consistent results across different methods. Via this approach, four distinct stages were identified, including: (I) FCC dendrite solidification, (II) solidification of FCC interdendritic region, (III) solid-state interdiffusion and (IV) final cooling with marginal diffusion. It was found out that in Stage I, Cu and Mn were rejected into liquid as Mn 35 Fe 5 Co 20 Ni 20 Cu 20 solidified dendritically. During Stage II, the lattice parameter disparity between dendrite and interdendritic region escalated as Cu and Mn continued segregating into the interdendritic region. After complete solidification, during Stage III, the lattice parameter disparity gradually decreases, demonstrating a degree of composition homogenization. The volume fraction of dendrites slightly grew from 58.3 to 65.5%, based on the evolving composition profile across a dendrite/interdendritic interface in diffusion calculations. Postmortem metallography further confirmed that dendrites have a volume fraction of 64.7 ± 5.3% in the final microstructure.
Aging behavior and strengthening mechanisms of coarsening resistant metastable θ' precipitates in an Al–Cu alloy
Not Available
Mechanisms of paint bake response in resistance spot-welded first and third generation AHSS
Implementation of 3rd generation advanced high strength steels (3GAHSS) in automotive structures requires careful consideration of joining process implications. Due to the presence of increased carbon equivalent in 3GAHSS such as 980 HF relative to commonly-applied 1st generation AHSS such as 980 DP, the resultant properties of the weld nugget and heat affected zones in resistance spot welded must be engineered to provide consistent and acceptable performance, specifically in cross-tension loading mode. Although the as-welded cross-tension strength (CTS) of 980 HF is less than 980 DP, there is a significant improvement of the CTS after paint baking in 980 HF welds. 980 DP steel welds do not exhibit such marked improvement upon baking. The mechanism of the strong and beneficial effect of paint baking on 980 HF in comparison to 980 DP is discussed in light of its effect on residual stress distributions and microstructures. Although residual stress (strain) reduction is observed via synchrotron x-ray diffraction for all tested steels, this effect is demonstrated as secondary to the performance restoration of the weld joint in cross tension. High-resolution electron channeling contrast imaging (ECCI) micrographs reveal that paint baking affects a more beneficial degree of martensite tempering in 980 HF as compared to 980 DP. The martensite tempering is also evidenced by both a reduction in nano-hardness of critical microstructural features and re-emergence of ductile fracture behavior following the paint baking process. The tempering of martensite is concluded to be the dominant mechanism in improving cross tension strength of 3GAHSS welds following paint baking.
Deformations of Ti-6Al-4V additive-manufacturing-induced isotropic and anisotropic columnar structures: Insitu measurements and underlying mechanisms
Not Available