Engineering topics

Ciancone, Michael L.

Publications and source records attributed to Ciancone, Michael L..

10 records

NASA NTRS2019

Challenges and Opportunities of International Cooperation for Safety & Mission Assurance (SMA) on the European Service Module (ESM) of the Orion Program

ESA is providing the ESM to NASA for the Orion Program in accordance with the Implementing Arrangement (IA) established between the two Agencies in 2012. This IA is a barter agreement, in which ESA provides Service Module vehicles for the first two flights of Orion in exchange for two servicing missions to the ISS. This arrangement has provided opportunities and challenges to both communities. It represents an important opportunity for ESA to build on its experience in the development and operations of ATV and play an active role in the development and flight of a manned space vehicle. This paper will explore some of the unique aspects of this arrangement as it affects Safety & Mission Assurance (SMA).The assessment of ESM compliance with applicable safety requirements is the responsibility of the Joint Safety and Engineering Review Panel (JSERP). The JSERP has two features that are relatively unique amongst NASA safety panels. First, NASA Engineering and SMA organizations co-chair this Panel. Previously, Safety has chaired, with Engineering as a member of the Panel. Inclusion of Engineering as a co-chair has offered greater leverage within the technical community. Second, the JSERP includes a second set of co-chairs from ESA Engineering and ESA Product Assurance and Safety (PA/S) organizations. This recognizes the international arrangement as one of partnership.Another source of both opportunity and challenge is the differing experience base of ESA and NASA. NASA has decades of experience in manned spaceflight, dating back to the Mercury program and following through Gemini, Apollo, Apollo-Soyuz, Skylab, Shuttle and the International Space Station. The risk posture for manned missions is much more rigorous than for unmanned missions. ESA brings a wealth of knowledge as well, with their flights of Ariane and Automated Transfer Vehicle (ATV), development and operation of the Columbus module on ISS, and satellite programs. The result is that both parties have developed paradigms related to risk and failure that contribute to ESM discussions.Orion represents humanity's first venture beyond Low-Earth Orbit (LEO) in over fifty years. Much of that experience is captured in program documents, but first-hand knowledge is limited to a few spaceflight veterans. Missions to LEO have offered the opportunity of direct, near-instantaneous communications and assistance, and the ability to return to Earth within a matter of hours in case of emergency. Outward-bound missions do not have these features and will require a more autonomous spacecraft with attendant safety-related issues.This paper will explore these and other challenges as we approach the flight of the first Orion vehicle.

Ciancone, Michael L.↗

NASA NTRS2002

Luigi Gussalli - Italian Spaceflight Visionary

The purpose of this paper is to heighten awareness within the space history community of the contributions of Luigi Gussalli, an Italian inventor and spaceflight visionary.

Ciancone, Michael L.↗

NASA NTRS2002

David Lasser - An American Spaceflight Pioneer

David Lasser was one of the founders of the American Interplanetary Society (later known as the American Rocket Society) and author of the first English-language book (in 1931) on the use of rockets for human spaceflight. His involvement in the fledgling spaceflight movement was short-lived as he moved on to pursue a distinguished, if turbulent, career in the labor movement. In lieu of an oral history, Mr. Lasser provided his recollections on the pioneering days of rocketry and his thoughts on mankind's destiny in space. This paper provides an overview of Mr. Lasser's life and accomplishments as an American spaceflight visionary, along with a compilation of the information that he graciously provided.

Ciancone, Michael L.↗

NASA NTRS1996

Spaceflight Safety on the North Coast of America

Spaceflight Safety (SFS) engineers at NASA Lewis Research Center (LeRC) are responsible for evaluating the microgravity fluids and combustion experiments, payloads and facilities developed at NASA LeRC which are manifested for spaceflight on the Space Shuttle, the Russian space station Mir, and/or the International Space Station (ISS). An ongoing activity at NASA LeRC is the comprehensive training of its SFS engineers through the creation and use of safety tools and processes. Teams of SFS engineers worked on the development of an Internet website (containing a spaceflight safety knowledge database and electronic templates of safety products) and the establishment of a technical peer review process (known as the Safety Assurance for Lewis Spaceflight Activities (SALSA) review).

Ciancone, Michael L.↗

NASA NTRS1989

Age distribution among NASA scientists and engineers

The loss of technical expertise through attrition in NASA and the aerospace industry is discussed. This report documents historical age-related information for scientific and engineering personnel in general and the NASA Lewis Research Center in particular, for 1968 through 1987. Recommendations are made to promote discussion and to establish the groundwork for action.

Ciancone, Michael L.↗

NASA NTRS1988

Mast material test program (MAMATEP)

The MAMATEP program, which is aimed at verifying the need for and evaluating the performance of various protection techniques for the solar array assembly mast of the Space Station photovoltaic power module, is discussed. Coated and uncoated mast material samples have been environmentally tested and evaluated, before and after testing, in terms of mass and bending modulus. The protective coatings include CV-1144 silicone, a Ni/Al/InSn eutectic, and an open-weave Al braid. Long-term plasma asher results from unprotected samples indicate that, even though fiberglass-epoxy samples degrade, a protection technique may not be necessary to ensure structural integrity. A protection technique, however, may be desirable to limit or contain the amount of debris generated by the degradation of the fiberglass-epoxy.

Ciancone, Michael L.↗

NASA NTRS1988

Oxidation and protection of fiberglass-epoxy composite masts for photovoltaic arrays in the low Earth orbital environment

Fiberglass-epoxy composites are considered for use as structural members for the mast of the space station solar array panel. The low Earth orbital environment in which space station is to operate is composed mainly of atomic oxygen, which has been shown to cause erosion of many organic materials and some metals. Ground based testing in a plasma asher was performed to determine the extent of degradation of fiberglass-epoxy composites when exposed to a simulated atomic oxygen environment. During exposure, the epoxy at the surface of the composite was oxidized, exposing individual glass fibers which could easily be removed. Several methods of protecting the composite were evaluated in an atomic oxygen environment and with thermal cycling and flexing. The protection techniques evaluated to date include an aluminum braid covering, an indium-tin eutectic and a silicone based paint. The open aluminum braid offered little protection while the CV-1144 coating offered some initial protection against atomic oxygen, but appears to develop cracks which accelerate degradation when flexed. Coatings such as the In-Sn eutectic may provide adequate protection by containing the glass fibers even though mass loss still occurs.

Rutledge, Sharon K.↗

NASA NTRS1988

Mast material test program (MAMATEP)

The Mast Material Test Program (MAMATEP) at NASA Lewis is discussed. Objectives include verifying the need for, and evaluating the performance of, various protection techniques for the Solar Array Assembly mast of the Space Station Photovoltaic Power Module. Mast material samples were evaluated in terms of mass and bending modulus, measured before and after environmental exposure. Test environments included atomic oxygen exposure (RF plasma asher), thermal cycling, and mechanical flexing. Protective coatings included CV-1144 silicon, a Ni/Au/InSn eutectic, and an open weave, Al braid. Results indicate that unprotected samples degrade in an atomic oxygen environment at a steady rate. Open weave, Al braid offers little protection for the fiberglass-epoxy sample in an asher environment. Ni/Au/InSn eutectic offers excellent protection in an asher environment prior to thermal cycling and mechanical flexing. Long duration asher results from unprotected samples indicate that, even though the fiberglass-epoxy degrades, a protection technique may not be necessary to ensure structural integrity. However, a protection technique may be desirable to limit or contain the amount of debris generated by the degradation of the fiberglass-epoxy.

Ciancone, Michael L.↗

NASA NTRS1988

Oxidation and protection of fiberglass-epoxy composite masts for photovoltaic arrays in the low earth orbital environment

The extent of degradation of fiberglass-epoxy composite masts of the Space Station solar array panel, when these are exposed to atomic oxygen environment of the low-earth orbit, was investigated in ground testing of fiberglass-epoxy composites in an RF plasma asher. In addition, several methods of protecting the composite structures were evaluated, including an aluminum braid covering, an In-Sn eutectic, and a silicone based paint. It was found that, during exposure, the epoxy at the surface of the composite was oxidized, exposing individual glass fibers which could easily be removed. The results of mass measurements and SEM examination carried out after thermal cycling and flexing of exposed composite samples indicated that coatings such as In-Sn eutectic may provide adequate protection by containing the glass fibers, even though mass loss still occurs.

Rutledge, Sharon K.↗

NASA NTRS1987

Flow visualization study of the effect of injection hole geometry on an inclined jet in crossflow

A flow visualization was studied by using neutrally buoyant, helium-filled soap bubbles, to determine the effect of injection hole geometry on the trajectory of an air jet in a crossflow and to investigate the mechanisms involved in jet deflection. Experimental variables were the blowing rate, and the injection hole geometry cusp facing upstream (CUS), cusp facing downstream (CDS), round, swirl passage, and oblong. It is indicated that jet deflection is governed by both the pressure drag forces and the entrainment of free-stream fluid into the jet flow. For injection hole geometries with similar cross-sectional areas and similar mass flow rates, the jet configuration with the larger aspect ratio experienced a greater deflection. Entrainment arises from lateral shearing forces on the sides of the jet, which set up a dual vortex motion within the jet and thereby cause some of the main-stream fluid momentum to be swept into the jet flow. This additional momentum forces the jet nearer the surface. Of the jet configurations, the oblong, CDS, and CUS configurations exhibited the largest deflections. The results correlate well with film cooling effectiveness data, which suggests a need to determine the jet exit configuration of optimum aspect ratio to provide maximum film cooling effectiveness.

Simon, Frederick F.↗