Search NASA⌕ Search

Engineering topics

Ciffone, D. L.

Publications and source records attributed to Ciffone, D. L..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Space missions for automation and robotics technologies (SMART) program

The motivations, features and expected benefits and applications of the NASA SMART program are summarized. SMART is intended to push the state of the art in automation and robotics, a goal that Public Law 98-371 mandated be an inherent part of the Space Station program. The effort would first require tests of sensors, manipulators, computers and other subsystems as seeds for the evolution of flight-qualified subsystems. Consideration is currently being given to robotics systems as add-ons to the RMS, MMU and OMV and a self-contained automation and robotics module which would be tended by astronaut visits. Probable experimentation and development paths that would be pursued with the equipment are discussed, along with the management structure and procedures for the program. The first hardware flight is projected for 1989.

Ciffone, D. L.↗
NASA NTRS1978

Measured wake-vortex characteristics of aircraft in ground effect

In support of the NASA wake vortex alleviation program, measurements were made of the influences of a ground plane on vortex trajectories and velocity profiles within lift-generated wakes. The wakes were generated by towing 0.61-m (2-ft) span models of two jumbo jets under water in a ship model basin. The models were configured with landing flaps and flight spoilers to investigate the wake characteristics of these aircraft in ground effect at simulated full-scale distances of 19 m (62 ft) to 116 m (380 ft) above the ground. The ground plane caused modifications in the vortex trajectories but did not alter vortex interactions and merging patterns in these multiple vortex wakes. Some distortions in vortex vertical (tangential) velocity profiles were recorded as a result of vortex lateral motions and vortex interactions with the viscous boundary layer on the ground plane; however, maximum tangential velocities remained unchanged.

Ciffone, D. L.↗
NASA NTRS1977

Application of laser velocimetry to aircraft wake-vortex measurements

The theory and use of a laser velocimeter that makes simultaneous measurements of vertical and longitudinal velocities while rapidly scanning a flow field laterally are described, and its direct application to trailing wake-vortex research is discussed. Pertinent measurements of aircraft wake-vortex velocity distributions obtained in a wind tunnel and water towing tank are presented. The utility of the velocimeter to quantitatively assess differences in wake velocity distributions due to wake dissipating devices and span loading changes on the wake-generating model is also demonstrated.

Ciffone, D. L.↗
NASA NTRS1976

Effects of spoilers and gear on B-747 wake vortex velocities

Vortex velocities were measured in the wakes of four configurations of a 0.61-m span model of a B-747 aircraft. The wakes were generated by towing the model underwater in a ship model basin. Tangential and axial velocity profiles were obtained with a scanning laser velocimeter as the wakes aged to 35 span lengths behind the model. A 45 deg deflection of two outboard flight spoilers with the model in the landing configuration resulted in a 36 percent reduction in wake maximum tangential velocity, altered velocity profiles, and erratic vortex trajectories. Deployment of the landing gear with the inboard flaps in the landing position and outboard flaps retracted had little effect on the flap vortices to 35 spans, but caused the wing tip vortices to have: (1) more diffuse velocity profiles; (2) a 27 percent reduction in maximum tangential velocity; and (3) a more rapid merger with the flap vortices.

Luebs, A. B.↗
NASA NTRS1976

Vortex interactions in multiple vortex wakes behind aircraft

A flow visualization technique has been developed which allows the nature of lift-generated wakes behind aircraft models to be investigated. Several different configurations of a 0.61-m span model of a Boeing 747-type transport aircraft were tested to allow observation of typical vortex interactions and merging in multiple vortex wakes. The vortices were identified by emitting tracer dyes from selected locations on the model. Wing span loading and model attitude were found to effect both vortex motions within the wake and resulting far-field wake velocity. Landing gear deployment caused a far-field reformation of vorticity behind a model configuration which dissipated concentrated vorticity in the near-field wake. A modified landing configuration was developed which appeared to significantly alleviate the concentrated wake vorticity.

Ciffone, D. L.↗
NASA NTRS1975

Experimental study of the effect of span loading on aircraft wakes

Measurements were made in the NASA-Ames 40- by 80-Foot Wind Tunnel of the rolling moment induced on a following model in the wake 13.6 spans behind a subsonic transport model for a variety of trailing edge flap settings of the generator. It was found that the rolling moment on the following model was reduced substantially, compared to the conventional landing configuration, by reshaping the span loading on the generating model to approximate a span loading, found in earlier studies, which resulted in reduced wake velocities. This was accomplished by retracting the outboard trailing edge flaps. It was concluded, based on flow visualization conducted in the wind tunnel as well as in a water tow facility, that this flap arrangement redistributes the vorticity shed by the wing along the span to form three vortex pairs that interact to disperse the wake.

Corsiglia, V. R.↗
NASA NTRS1975

Flow visualization of vortex interactions in multiple vortex wakes behind aircraft

A flow visualization technique was developed which allows the nature of lift-generated wakes behind aircraft models to be investigated. The technique was applied to models being towed underwater in a ship model basin. Seven different configurations of a small-scale model of a 747 transport aircraft were used to allow observation of typical vortex interactions and merging in multiple vortex wakes. It was established that the motion of the wake vortices is often sensitive to small changes in either wing span loading or model attitude. Landing gear deployement was found to cause a far-field reformation of vorticity behind a model configuration which dissipated concentrated vorticity in the near-field wake. Alleviation of wake vorticity is achievable by configuring the wing span loading to cause the wake vortices to move in paths that result in their interactions and merging. The vortices shed from the horizontal stabilizer always moved down rapidly into the wake and merged with the other vortices, primarily the inboard flap vortices.

Ciffone, D. L.↗
NASA NTRS1975

Experimental study of the effect on span loading on aircraft wakes

Measurements were made in the NASA-Ames 40- by 80-foot wind tunnel of the rolling moment induced on a following model in the wake 13.6 spans behind a subsonic transport model for a variety of trailing edge flap settings of the generator. It was found that the rolling moment on the following model was reduced substantially, compared to the conventional landing configuration, by reshaping the span loading on the generating model to approximate a span loading, found in earlier studies, which resulted in reduced wake velocities. This was accomplished by retracting the outboard trailing edge flaps. It was concluded, based on flow visualization conducted in the wind tunnel as well as in a water tow facility, that this flap arrangement redistributes the vorticity shed by the wing along the span to form three vortex pairs that interact to disperse the wake.

Corsiglia, V. R.↗
NASA NTRS1974

Correlation for estimating vortex rotational velocity downstream dependence

Description of a correlation, derived from water tank measurements in the wake of wings towed under water, that makes it possible to predict the downstream distance behind an aircraft in flight where its trailing vortex will begin to decay. Comparisons of measured and predicted data are discussed.

Ciffone, D. L.↗
NASA NTRS1974

Axial flow measurements in trailing vortices

A scanning laser Doppler velocimeter was used to measure the axial velocity defect in the cores of trailing vortices behind a lifting airfoil of rectangular planform. Data were obtained at several different angles of attack and downstream distances ranging from 30 to 1000 chord lengths. The test was designed to obtain continuous data from the near field into the far field while removing uncertainties associated with the interpretation of data obtained by the hydrogen bubble technique. The measured velocities of V sub x/U sub infinity are compared with those predicted. The agreement is remarkably good over the entire range of downstream distances, which supports the credibility of calculating axial velocities using the results of Moore and Saffman (1973).

Ciffone, D. L.↗
NASA NTRS1974

Far-field wake-vortex characteristics of wings

Velocity measurements have been made in the wake of wings that were being towed underwater. As the wake aged, measurements of the tangential and axial velocity profiles were made with a two-dimensional scanning laser velocimeter at downstream distances of 5 to 200 span lengths behind wings with different span loadings. The results identify two characteristic flow regions for the dependence of vortex maximum tangential velocity on downstream distance. The first, a region with little, if any, change in maximum tangential velocity, extends from wake rollup to downstream distances as great as 100 span lengths, depending on span loading and angle of attack. This is followed by a decay region in which the maximum tangential velocity decreases with downstream distance at rates nominally proportional to the inverse one-half power.

Ciffone, D. L.↗
NASA NTRS1974

Vortex measurements behind a swept wing transport model

A backscatter laser Doppler velocimeter which simultaneously senses the axial and the tangential components of the velocity has been used to measure the velocity distributions in the near wake of a swept wing semispan transport model in a wind tunnel. The model configuration included nacelles, pylons, antishock bodies, and wing flaps which could be deflected 27 deg. Typical wake vortex velocity profiles are presented for the flaps-retracted and the flaps-deployed 27 deg configurations, respectively.

Orloff, K. L.↗
NASA NTRS1973

Airfoil wake vortex characteristics in the far field

Tangential and axial velocity profiles were measured in the far field wake vortices of several different airfoils. The results are summarized and discussed. A scanning laser velocimeter was used to obtain data up to 1000 chord lengths behind airfoils with rectangular, diamond-shaped, and swept wing planforms at several different angles of attack. The results show general agreement with wind tunnel measurements made in the near field. The results identify two separate flow regions for the dependence of vortex maximum tangential velocity on downstream distance; an inviscid region where the velocity remains constant after rollup to downstream distances of 200 chord lengths, and then a decay or viscous region that persisted to the limit of the test distance. The decay rates appear to be sensitive to both angle of attack and span loading. The maximum tangential velocity for downstream distances to 40 span lengths was reduced by a factor of 2 by changing from an elliptic (swept wing) or rectangular span loading to a triangular-like span loading (diamond-shaped planform wing). Measured axial velocity defects are shown to agree with those predicted by laminar theory.

Orloff, K. L.↗
NASA NTRS1973

Laser Doppler velocimeter investigation of trailing vortices behind a semi-span swept wing in a landing configuration

Measured axial and tangential velocity profiles in the near wake vortices of a semi-span model of the Convair 990 wing in the NASA-Ames 7- by 10-foot wind tunnel are presented. A scanning laser Doppler velocimeter was used to obtain data at two different downstream stations (0.49 and 1.25 wing spans) at various angles of attack and configurations from wing alone to wing plus nacelles, anti-shock bodies, and flaps deflected 27 deg (landing configuration). It is shown that the velocity distributions within the wake are quite sensitive to span loading. Specifically, it is illustrated that an aircraft flying at given lift coefficient (C SUB L), can substantially reduce its trailing vortex upset potential by deploying its flaps and altering its flight attitude to maintain the same C SUB L. This might be taken into consideration along with performance and noise considerations in the selection of aircraft approach lift over drag.

Ciffone, D. L.↗
NASA NTRS1973

A simulator investigation of the influence of engine response characteristics on the approach and landing for an externally blown flap aircraft. Part 2: Aerodynamic model

An analysis of the influence of engine response characteristics on the approach and landing of an externally blown flap aircraft was conducted using flight simulator facilities. The configuration of the aerodynamic model is described. The aerodynamic characteristics as a function of angle of attack, thrust coefficient, and flap deflection are presented in tabular form and as graphs.

Ciffone, D. L.↗