Search NASA⌕ Search

Engineering topics

Cihan, Abdullah

Publications and source records attributed to Cihan, Abdullah.

At least 37 records · Page 2

Methane Diffusion and Adsorption in Shale Rocks: A Numerical Study Using the Dusty Gas Model in TOUGH2/EOS7C-ECBM

Gas production from shale gas reservoirs plays a significant role in satisfying increasing energy demands. Compared with conventional sandstone and carbonate reservoirs, shale gas reservoirs are characterized by extremely low porosity, ultra-low permeability and high clay content. Slip flow, diffusion, adsorption and desorption are the primary gas transport processes in shale matrix, while Darcy flow is restricted to fractures. Understanding methane diffusion and adsorption, and gas flow and equilibrium in the low-permeability matrix of shale is crucial for shale formation evaluation and for predicting gas production. Modeling of diffusion in low-permeability shale rocks requires use of the Dusty gas model (DGM) rather than Fick’s law. The DGM is incorporated in the TOUGH2 module EOS7C-ECBM, a modified version of EOS7C that simulates multicomponent gas mixture transport in porous media. Also included in EOS7C-ECBM is the extended Langmuir model for adsorption and desorption of gases. In this study, a column shale model was constructed to simulate methane diffusion and adsorption through shale rocks. The process of binary CH 4 - N 2 diffusion and adsorption was analyzed. A sensitivity study was performed to investigate the effects of pressure, temperature and permeability on diffusion and adsorption in shale rocks. The results show that methane gas diffusion and adsorption in shale is a slow process of dynamic equilibrium, which can be illustrated by the slope of a curve in CH4mass variation. The amount of adsorption increases with the pressure increase at the low pressure, and the mass change by gas diffusion will decrease due to the decrease in the compressibility factor of the gas. With the elevated temperature, the gas molecules move faster and then the greater gas diffusion rates make the process duration shorter. The gas diffusion rate decreases with the permeability decrease, and there is a limit of gas diffusion if the permeability is less than 1.0×10 -15 m 2 . In conclusion, the results can provide insights for a better understanding of methane diffusion and adsorption in the shale rocks so as to optimize gas production performance of shale gas reservoirs.

04 OIL SHALES AND TAR SANDS↗

Water Saturation Relations and Their Diffusion-Limited Equilibration in Gas Shale: Implications for Gas Flow in Unconventional Reservoirs

Large volumes of water are used for hydraulic fracturing of low permeability shale reservoirs to stimulate gas production, with most of the water remaining unrecovered and distributed in a poorly understood manner within stimulated regions. Because water partitioning into shale pores controls gas release, we measured the water saturation dependence on relative humidity (rh) and capillary pressure (P c ) for imbibition (adsorption) as well as drainage (desorption) on samples of Woodford Shale. Experiments and modeling of water vapor adsorption into shale laminae at rh = 0.31 demonstrated that long times are needed to characterize equilibrium in larger (5 mm thick) pieces of shales, and yielded effective diffusion coefficients from 9 × 10 -9 to 3 × 10 -8 m 2 s -1 , similar in magnitude to the literature values for typical low porosity and low permeability rocks. Most of the experiments, conducted at 50°C on crushed shale grains in order to facilitate rapid equilibration, showed significant saturation hysteresis, and that very large P c (~1 MPa) are required to drain the shales. These results quantify the severity of the water blocking problem, and suggest that gas production from unconventional reservoirs is largely associated with stimulated regions that have had little or no exposure to injected water. Finally, gravity drainage of water from fractures residing above horizontal wells reconciles gas production in the presence of largely unrecovered injected water, and is discussed in the broader context of unsaturated flow in fractures.

58 GEOSCIENCES↗

Mixing and trapping of dissolved CO 2 in deep geologic formations with shale layers

For dissolution trapping, the spatial variability of the geologic properties of naturally complex storage formations can significantly impact flow patterns and storage mechanisms of dissolved CO 2 . The significance of diffusive mixing that occurs in low permeability layers embedded between relatively higher permeability materials was highlighted by Agartan et al. (2015) using a highly controlled laboratory experimental study on trapping of dissolved CO 2 in multilayered systems. In this paper, we present a numerical modeling study on the impacts of low permeability layers on flow and storage of dissolved CO 2 in realistic field-scale settings. The simulator of variable-density flow used in this study was first verified using the experimental data in Agartan et al. (2015) to capture the observed processes. The simulator was then applied to a synthetic, field-scale multilayered system, with 19 sensitivity cases having variable permeability and thickness of the shale layers as well as the source strength and geometry of the source zone of dissolved CO 2 . Simulation results showed that the presence of continuous shale layers in the storage system disrupts the convective mixing by enhancing lateral spreading of dissolved CO 2 in sandstone layers and retarding the vertical mixing of dissolved CO 2 . The effectiveness of trapping of dissolved CO 2 depends on the physical properties of the shale layers and configurations of the source zone. The comparison to homogeneous cases with effective vertical permeability shows that it is important to capture these continuous thin shale layers in a storage formation and include them in the models to enhance dissolution trapping.

58 GEOSCIENCES↗

A risk map methodology to assess the spatial and temporal distribution of leakage into groundwater from Geologic Carbon Storage

The risks to potable aquifers due to brine leakage through plugged and abandoned (P&A) wells is highly uncertain and a potentially significant contributor to the risk profile in Geologic Carbon Storage (GCS). This uncertainty stems from the unknown location of wells and the large variance of P&A wellbore permeability, making the spatial assessment of P&A brine leakage risk challenging. A new methodology is presented to generate “risk maps”, or spatial distributions of brine leakage risk to groundwater resources as defined with no-impact or Maximum Contaminant Level (MCL) thresholds. The methodology utilizes probability theory, thereby avoiding the use of computationally expensive Monte Carlo simulations while maintaining flexibility in modeling techniques. These maps provide quantitative probabilities of risk as a function of time to inform site selection and monitoring during and post-injection, conducive to the US EPA's permitting of class-VI wells and the so-called “area of review”, AoR. As a demonstration of the methodology, a numerical model of a hypothetical fully-coupled system spanning from the injection reservoir to the USDW is used to assess the evolution of brine leakage through P&A wells. Risk maps of CO 2 leakage can also be generated with this methodology for a comprehensive assessment of GCS leakage risk.

58 GEOSCIENCES↗

Investigation of representing hysteresis in macroscopic models of two-phase flow in porous media using intermediate scale experimental data

Incorporating hysteresis into models is important to accurately capture the two phase flow behavior when porous media systems undergo cycles of drainage and imbibition such as in the cases of injection and post-injection redistribution of CO 2 during geological CO 2 storage (GCS). In the traditional model of two-phase flow, existing constitutive models that parameterize the hysteresis associated with these processes are generally based on the empirical relationships. This manuscript presents development and testing of mathematical hysteretic capillary pressure—saturation—relative permeability models with the objective of more accurately representing the redistribution of the fluids after injection. The constitutive models are developed by relating macroscopic variables to basic physics of two-phase capillary displacements at pore-scale and void space distribution properties. The modeling approach with the developed constitutive models with and without hysteresis as input is tested against some intermediate-scale flow cell experiments to test the ability of the models to represent movement and capillary trapping of immiscible fluids under macroscopically homogeneous and heterogeneous conditions. The hysteretic two-phase flow model predicted the overall plume migration and distribution during and post injection reasonably well and represented the postinjection behavior of the plume more accurately than the nonhysteretic models. In conclusion, based on the results in this study, neglecting hysteresis in the constitutive models of the traditional two-phase flow theory can seriously overpredict or underpredict the injected fluid distribution during post-injection under both homogeneous and heterogeneous conditions, depending on the selected value of the residual saturation in the nonhysteretic models.

58 GEOSCIENCES↗

Imaging and quantification of spreading and trapping of carbon dioxide in saline aquifers using meter-scale laboratory experiments

The role of capillary forces during buoyant migration of CO 2 is critical toward plume immobilization within the postinjection phase of a geological carbon sequestration operation. However, the inherent heterogeneity of the subsurface makes it very challenging to evaluate the effects of capillary forces on the storage capacity of these formations and to assess in situ plume evolution. To overcome the lack of accurate and continuous observations at the field scale and to mimic vertical migration and entrapment of realistic CO 2 plumes in the presence of a background hydraulic gradient, we conducted two unique long-term experiments in a 2.44 m × 0.5 m tank. X-ray attenuation allowed measuring the evolution of a CO 2 -surrogate fluid saturation, thus providing direct insight into capillarity-dominated and buoyancy-dominated flow processes occurring under successive drainage and imbibition conditions. The comparison of saturation distributions between two experimental campaigns suggests that layered-type heterogeneity plays an important role on nonwetting phase (NWP) migration and trapping, because it leads to (i) longer displacement times (3.6 months versus 24 days) to reach stable trapping conditions, (ii) limited vertical migration of the plume (with center of mass at 39% versus 55% of aquifer thickness), and (iii) immobilization of a larger fraction of injected NWP mass (67.2% versus 51.5% of injected volume) as compared to the homogenous scenario. Finally, while these observations confirm once more the role of geological heterogeneity in controlling buoyant flows in the subsurface, they also highlight the importance of characterizing it at scales that are below seismic resolution (1–10 m).

54 ENVIRONMENTAL SCIENCES↗

Enhancing capillary trapping effectiveness through proper time scheduling of injection of supercritical CO 2 in heterogeneous formations

The impact of geologic heterogeneity on capillary trapping of supercritical CO 2 (scCO 2 ) has been recognized and appraised through laboratory experimentation and modeling. However, how different injection strategies can be optimized to improve capillary trapping has not received adequate attention. Here, we present a study based on stochastic analysis to show the impact of injection scheduling on capillary trapping of scCO 2 in heterogeneous geological formations. Improvement of trapping efficiency consists of maximizing the trapped volume within a predefined secure zone of the storage formation with the goal of avoiding plume intersection with potential leakage pathways. Using knowledge acquired from physical experiments in intermediate-scale tanks with controlled heterogeneity, we conduct numerical simulations following a stochastic approach to extend the observed outcomes to a series of equally probable permeability scenarios. Our simulations involve the same combination of surrogate fluids that are used in the experiments to mimic viscosity and density contrasts between scCO 2 and brine. To account for uncertainty of formation heterogeneity, several permeability fields with three different variances and two horizontal correlation lengths are generated. The same volume of scCO 2 is emplaced using four different modes of injection scheduling. Results suggest that injection strategies aimed at enhancing capillary trapping of scCO 2 and increasing the probability of constraining the plume within a secure zone are strictly related to the specific heterogeneity of the reservoir. Finally, this preliminary theoretical finding suggests the potential for maximizing secure capillary trapping through the proper selection of injection schedule to fit the formation heterogeneity.

58 GEOSCIENCES↗

Geologic carbon sequestration injection wells in overpressured storage reservoirs: estimating area of review

The Area of Review (AoR) under the US Environmental Protection Agency's (EPA) Class VI CO 2 injection permit is defined as the region surrounding the geologic carbon sequestration (GCS) project where underground sources of drinking water (USDWs) may be endangered. Estimation of the AoR is based on the calculated reservoir pressurization due to CO 2 injection and the associated potential to lift saline water into potable groundwater aquifers through open flow paths (e.g. wells) assuming the system is hydrostatic. In cases where the storage reservoirs are not initially hydrostatic, and in particular where they are overpressured, AoR estimation methods need to be altered. Here in this paper, we present and apply an approach to evaluating potential endangerment of USDW based on comparing brine leakage through a hypothetical open flow path in a no-injection scenario and brine leakage in a CO 2 -injection scenario. We present six possible ways to normalize injection-related leakage relative to no-injection leakage. We calculate leakage using semi-analytical solutions for single-phase flow and model reservoir pressurization and flow up (single) leaky wells located progressively farther from the injection well. For an example case of relative overpressure and using an injection-rate-based approach, results show 50-60% larger open-well-leakage rates for wells located at 2 km and 10% increase for wells located at 10 km from the injection well relative to the no-injection case. If total brine leakage is considered, the results depend strongly on the assumed pre-injection to post-injection time frames and on the methods of normalization used to calculate incremental leakage.

54 ENVIRONMENTAL SCIENCES↗

On the use of Darcy's law and invasion-percolation approaches for modeling large-scale geologic carbon sequestration

Most large-scale flow and transport simulations for geologic carbon sequestration (GCS) applications are carried out using simulators that solve flow equations arising from Darcy's law. Recently, the computational advantages of invasion-percolation (IP) modeling approaches have been presented. We show that both the Darcy's-law- and the gravity-capillary balance solved by IP approaches can be derived from the same multiphase continuum momentum equation. More specifically, Darcy's law arises from assuming creeping flow with no viscous momentum transfer to stationary solid grains, while it is assumed in the IP approach that gravity and capillarity are the dominant driving forces in a quasi-static two-phase (or more) system. There is a long history of use of Darcy's law for large-scale GCS simulation. However, simulations based on Darcy's law commonly include significant numerical dispersion as users employ large grid blocks to keep run times practical. In contrast, the computational simplicity of IP approaches allows large-scale models to honor fine-scale hydrostratigraphic details of the storage formation which makes these IP models suitable for analyzing the impact of small-scale heterogeneities on flow. However, the lack of time-dependence in the IP models is a significant disadvantage, while the ability of Darcy's law to simulate a range of flows from single-phase- and pressure-gradient-driven flows to buoyant multiphase gravity-capillary flow is a significant advantage. We believe on balance that Darcy's law simulations should be the preferred approach to large-scale GCS simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental analysis of spatial correlation effects on capillary trapping of supercritical CO 2 at the intermediate laboratory scale in heterogeneous porous media

Several numerical studies have demonstrated that the heterogeneous nature of typical sedimentary formations can favorably dampen the accumulation of mobile CO 2 phase underneath the caprock. Core flooding experiments have also shown that contrasts in capillary entry pressure can lead to buildup of nonwetting fluid phase (NWP) at interfaces between facies. Explicit representation of geological heterogeneity at the intermediate (cm-to-m) scale is a powerful approach to identify the key mechanisms that control multiphase flow dynamics in porous media. The ability to carefully control flow regime and permeability contrast at a scale that is relevant to CO 2 plume dynamics in saline formations offers valuable information to understand immiscible displacement processes and provides a benchmark for mathematical models. To provide insight into the impact of capillary heterogeneity on flow dynamics and trapping efficiency of supercritical CO 2 under successive drainage and imbibition conditions, we present an experimental investigation conducted in a synthetic sand reservoir. By mimicking the interplay of governing forces at reservoir conditions via application of surrogate fluids, we performed three immiscible displacement experiments to observe the entrapment of NWP in heterogeneous porous media. Capillary trapping performance is evaluated for each scenario through spatial and temporal variations of NWP saturation; for this reason we adopted X-ray attenuation to precisely measure phase saturation throughout the flow domain and apply spatial moment analysis. Furthermore, the sweeping performance of two different permeability fields with comparable variance but distinct spatial correlation was compared against a homogeneous base case with equivalent mean permeability by means of spatial moment analysis.

58 GEOSCIENCES↗

Optimal well placement and brine extraction for pressure management during CO 2 sequestration

Large-scale pressure increases resulting from carbon dioxide (CO 2 ) injection in the subsurface can potentially impact caprock integrity, induce reactivation of critically stressed faults, and drive CO 2 or brine through conductive features into shallow groundwater. Pressure management involving the extraction of native fluids from storage formations can be used to reduce such pressure increases. However, dealing with large volumes of extracted brine can be technically challenging and expensive. Selection of optimal well locations and pumping rates are critical for maximizing CO 2 storage and minimizing brine extraction during geologic CO 2 sequestration (GCS). Robust and efficient computerized algorithms combining reservoir models and optimization methods are needed to make proper decisions on well placement and pumping rates. This work presents a constrained differential evolution (CDE) algorithm for solving global optimization problems involving pressure management of GCS projects. Application of the CDE optimization methodology was demonstrated for a hypothetical CO 2 storage scenario in a deep sandstone reservoir in the Southern San Joaquin Basin in California, USA. Industrial-scale storage of CO 2 would generate significant pressure buildup in this formation, which in turn would raise concerns about induced seismicity due to presence of multiple faults surrounding the injection site. Through the CDE optimization algorithm coupled to a vertically-averaged reservoir simulator, we successfully estimated optimal solutions for brine extraction wells in the reservoir that would limit the local pressure along the faults to a prescribed threshold. Multiple realizations of the reservoir permeability field were created to understand the impact of reservoir heterogeneity on optimization results. Our results indicate that the reservoir slope and heterogeneity have significant impact on optimum extraction rates. Reservoir heterogeneity is also a significant factor for extraction well locations, suggesting that in practice decisions about extraction well placement through optimization should be made at later project stages when data from a few years of CO 2 injection have allowed iterative updating and refining of the reservoir forward models. Although the study focused on optimization of brine extraction, the CDE optimization methodology presented in this paper has also potential to solve other complex optimization problems related to GCS, such as increasing storage efficiency by enhancing injectivity and capillary and dissolution trapping.

58 GEOSCIENCES↗

Intermediate Scale Laboratory Testing to Understand Mechanisms of Capillary and Dissolution Trapping during Injection and Post-Injection of CO 2 in Heterogeneous Geological Formations

Carbon Capture and Storage (CCS) represents a technology aimed to reduce atmospheric loading of CO 2 from power plants and heavy industries by injecting it into deep geological formations, such as saline aquifers. A number of trapping mechanisms contribute to effective and secure storage of the injected CO 2 in supercritical fluid phase (scCO 2 ) in the formation over the long term. The primary trapping mechanisms are structural, residual, dissolution and mineralization. Knowledge gaps exist on how the heterogeneity of the formation manifested at all scales from the pore to the site scales affects trapping and parameterization of contributing mechanisms in models. An experimental and modeling study was conducted to fill these knowledge gaps. Experimental investigation of fundamental processes and mechanisms in field settings is not possible as it is not feasible to fully characterize the geologic heterogeneity at all relevant scales and gathering data on migration, trapping and dissolution of scCO 2 . Laboratory experiments using scCO 2 under ambient conditions are also not feasible as it is technically challenging and cost prohibitive to develop large, two- or three-dimensional test systems with controlled high pressures to keep the scCO 2 as a liquid. Hence, an innovative approach that used surrogate fluids in place of scCO 2 and formation brine in multi-scale, synthetic aquifers test systems ranging in scales from centimeter to meter scale developed used. New modeling algorithms were developed to capture the processes controlled by the formation heterogeneity, and they were tested using the data from the laboratory test systems. The results and findings are expected to contribute toward better conceptual models, future improvements to DOE numerical codes, more accurate assessment of storage capacities, and optimized placement strategies. This report presents the experimental and modeling methods and research results.

54 ENVIRONMENTAL SCIENCES↗

Experimental study on effects of geologic heterogeneity in enhancing dissolution trapping of supercritical CO 2

Abstract Dissolution trapping is one of the primary mechanisms that enhance the storage security of supercritical carbon dioxide (scCO 2 ) in saline geologic formations. When scCO 2 dissolves in formation brine produces an aqueous solution that is denser than formation brine, which leads to convective mixing driven by gravitational instabilities. Convective mixing can enhance the dissolution of CO 2 and thus it can contribute to stable trapping of dissolved CO 2 . However, in the presence of geologic heterogeneities, diffusive mixing may also contribute to dissolution trapping. The effects of heterogeneity on mixing and its contribution to stable trapping are not well understood. The goal of this experimental study is to investigate the effects of geologic heterogeneity on mixing and stable trapping of dissolved CO 2 . Homogeneous and heterogeneous media experiments were conducted in a two‐dimensional test tank with various packing configurations using surrogates for scCO 2 (water) and brine (propylene glycol) under ambient pressure and temperature conditions. The results show that the density‐driven flow in heterogeneous formations may not always cause significant convective mixing especially in layered systems containing low‐permeability zones. In homogeneous formations, density‐driven fingering enhances both storage in the deeper parts of the formation and contact between the host rock and dissolved CO 2 for the potential mineralization. On the other hand, for layered systems, dissolved CO 2 becomes immobilized in low‐permeability zones with low‐diffusion rates, which reduces the risk of leakage through any fault or fracture. Both cases contribute to the permanence of the dissolved plume in the formation.

Agartan, Elif↗

Multiphase Modeling of Geologic Carbon Sequestration in Saline Aquifers

Abstract Geologic carbon sequestration ( GCS ) is being considered as a climate change mitigation option in many future energy scenarios. Mathematical modeling is routinely used to predict subsurface CO 2 and resident brine migration for the design of injection operations, to demonstrate the permanence of CO 2 storage, and to show that other subsurface resources will not be degraded. Many processes impact the migration of CO 2 and brine, including multiphase flow dynamics, geochemistry, and geomechanics, along with the spatial distribution of parameters such as porosity and permeability. In this article, we review a set of multiphase modeling approaches with different levels of conceptual complexity that have been used to model GCS . Model complexity ranges from coupled multiprocess models to simplified vertical equilibrium (VE) models and macroscopic invasion percolation models. The goal of this article is to give a framework of conceptual model complexity, and to show the types of modeling approaches that have been used to address specific GCS questions. Application of the modeling approaches is shown using five ongoing or proposed CO 2 injection sites. For the selected sites, the majority of GCS models follow a simplified multiphase approach, especially for questions related to injection and local‐scale heterogeneity. Coupled multiprocess models are only applied in one case where geomechanics have a strong impact on the flow. Owing to their computational efficiency, VE models tend to be applied at large scales. A macroscopic invasion percolation approach was used to predict the CO 2 migration at one site to examine details of CO 2 migration under the caprock.

Bandilla, Karl W.↗

A connectivity-based modeling approach for representing hysteresis in macroscopic two-phase flow properties

During CO 2 injection and storage in deep reservoirs, the injected CO 2 enters into an initially brine saturated porous medium, and after the injection stops, natural groundwater flow eventually displaces the injected mobile-phase CO 2 , leaving behind residual non-wetting fluid. Accurate modeling of two-phase flow processes are needed for predicting fate and transport of injected CO 2 , evaluating environmental risks and designing more effective storage schemes. The entrapped non-wetting fluid saturation is typically a function of the spatially varying maximum saturation at the end of injection. At the pore-scale, distribution of void sizes and connectivity of void space play a major role for the macroscopic hysteresis behavior and capillary entrapment of wetting and non-wetting fluids. This paper presents development of an approach based on the connectivity of void space for modeling hysteretic capillary pressure-saturation-relative permeability relationships. The new approach uses void-size distribution and a measure of void space connectivity to compute the hysteretic constitutive functions and to predict entrapped fluid phase saturations. Two functions, the drainage connectivity function and the wetting connectivity function, are introduced to characterize connectivity of fluids in void space during drainage and wetting processes. These functions can be estimated through pore-scale simulations in computer-generated porous media or from traditional experimental measurements of primary drainage and main wetting curves. The hysteresis model for saturation-capillary pressure is tested successfully by comparing the model-predicted residual saturation and scanning curves with actual data sets obtained from column experiments found in the literature. A numerical two-phase model simulator with the new hysteresis functions is tested against laboratory experiments conducted in a quasi-two-dimensional flow cell (91.4cm×5.6cm×61cm), packed with homogeneous and heterogeneous sands. Initial results show that the model can predict spatial and temporal distribution of injected fluid during the experiments reasonably well. However, further analyses are needed for comprehensively testing the ability of the model to predict transient two-phase flow processes and capillary entrapment in geological reservoirs during geological carbon sequestration.

58 GEOSCIENCES↗

Delineating Area of Review in a System with Pre-injection Relative Overpressure

The Class VI permit application for geologic carbon sequestration (GCS) requires delineation of an area of review (AoR), defined as the region surrounding the (GCS) project where underground sources of drinking water (USDWs) may be endangered. The methods for estimating AoR under the Class VI regulation were developed assuming that GCS reservoirs would be in hydrostatic equilibrium with overlying aquifers. Here we develop and apply an approach to estimating AoR for sites with preinjection relative overpressure for which standard AoR estimation methods produces an infinite AoR. The approach we take is to compare brine leakage through a hypothetical open flow path in the base-case scenario (no-injection) to the incrementally larger leakage that would occur in the CO 2 -injection case. To estimate AoR by this method, we used semi-analytical solutions to single-phase flow equations to model reservoir pressurization and flow up (single) leaky wells located at progressively greater distances from the injection well. We found that the incrementally larger flow rates for hypothetical leaky wells located 6 km and 4 km from the injection well are ~20% and 30% greater, respectively, than hypothetical baseline leakage rates. If total brine leakage is considered, the results depend strongly on how the incremental increase in total leakage is calculated, varying from a few percent to up to 40% greater (at most at early time) than base-case total leakage.

58 GEOSCIENCES↗