Search NASA⌕ Search

Engineering topics

Clark, D.

Publications and source records attributed to Clark, D..

At least 19 records

Design Improvements in Liquid Argon Purification Techniques in DUNE Cold Electronics Test Cryostat (Iceberg)

A proposed design improvement for the removal of electronegative impurities from liquid argon for the purpose of neutrino detector research is described. The design will utilize a commercially available submersible pump to circulate liquid argon through an external filter containing molecular sieve and activated copper media, removing water and oxygen, respectively. The existing state-of-the-art filter design provides a throughput of 0.5 L/min, while the capacity of the submersible pump design is at least 4 L/min, though could be even higher depending on total losses within the filtration piping assembly. An additional benefit of the new design will be the ability to regenerate the filter media in situ without stopping the experimental testing. The following work will describe the design, operation, and expected performance using CFD analysis.

Schwartz, F.↗

Correcting Hohlraum Drive Asymmetry with Glow Discharge Polymerization Coated Capsule Shims

In inertial confinement fusion target design, the shape discrepancy between the cylindrical hohlraum and the spherical capsule creates a low mode asymmetry in the implosion. One way to correct such asymmetry is to shim the target capsule surface with extra mass in specific locations following a 3D P4 Legendre mode. Previously, the desired surface pattern was precision machined out of the capsule. The resulting 2DConA experiments that investigated the implosion’s shape demonstrated the shimming method’s success. However, machining leaves large defects on the capsule surface which will degrade neutron yield in a DT implosion. An alternative shimming approach is to grow the pattern on the capsule surface using a glow discharge polymerization coating process in a stencil lithography application. In this study, we discuss the fabrication, characterization and challenges of making shimmed target capsules with this new method.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reaching a burning plasma and ignition using smaller capsules/ Hohlraums , higher radiation temperatures, and thicker ablator/ice on the national ignition facility

In indirect-drive implosions, the final core hot spot energy and pressure and, hence, neutron yield attainable in 1D increase with increasing laser peak power and, hence, radiation drive temperature at the fixed capsule and Hohlraum size. Here we present simple analytic scalings validated by 1D simulations that quantify the improvement in performance and use this to explain existing data and simulation trends. Extrapolating to the 500 TW National Ignition Facility peak power limit in a low gas-fill 5.4 mm diameter Hohlraum based on existing high adiabat implosion data at 400 TW, 1.3 MJ and 1 × 10 16 yield, we find that a 2–3 × 10 17 yield (0.5–0.7 MJ) is plausible using only 1.8 MJ of laser energy. Based on existing data varying deuterium–tritium (DT) fuel thickness and dopant areal density, further improvements should be possible by increasing DT fuel areal density, and hence confinement time and yield amplification.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Alpha heating of indirect-drive layered implosions on the National Ignition Facility

We report in order to understand how close current layered implosions in indirect-drive inertial confinement fusion are to ignition, it is necessary to measure the level of alpha heating present. To this end, pairs of experiments were performed that consisted of a low-yield tritium–hydrogen–deuterium (THD) layered implosion and a high-yield deuterium–tritium (DT) layered implosion to validate experimentally current simulation-based methods of determining yield amplification. The THD capsules were designed to reduce simultaneously DT neutron yield (alpha heating) and maintain hydrodynamic similarity with the higher yield DT capsules. The ratio of the yields measured in these experiments then allowed the alpha heating level of the DT layered implosions to be determined. The level of alpha heating inferred is consistent with fits to simulations expressed in terms of experimentally measurable quantities and enables us to infer the level of alpha heating in recent high-performing implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hydroscaling indirect-drive implosions on the National Ignition Facility

A goal of the laser-based National Ignition Facility (NIF) is to increase the liberated fusion energy “yield” in inertial confinement fusion experiments well past the ignition threshold and the input laser energy. One method of increasing the yield, hydrodynamic scaling of current experiments, does not rely on improving compression or implosion velocity, but rather increases the scale of the implosion to increase hotspot areal density and confinement time. Indirect-drive (Hohlraum driven) implosions carried out at two target sizes, 12.5% apart, have validated hydroscaling expectations. Moreover, extending comparisons to the best-performing implosions at five different capsule sizes shows that their performance also agrees well with hydroscaling expectations even though not direct hydroscales of one another. In the future, by switching to a reduced loss Hohlraum geometry, simulations indicate that we can drive 20% larger-scale implosions within the current power and energy limitations on the NIF. Finally, at the demonstrated compression and velocity of these smaller-scale implosions, these 1.2× hydroscaled implosions should put us well past the ignition threshold.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Characterization and qualification of neutron radiation effects – Summary of Japan-USA Joint Projects for 40 years

The Joint Projects under the Japan-USA Fusion Cooperation Program started in 1981 and has continued for more than 40 years. In the Joint Projects, although a wide range of fusion materials and engineering issues were covered, neutron radiation effects on fusion reactor materials have always been the major research emphases, and the neutron irradiation facilities in the US were jointly used by Japanese and US researchers. Japanese test facilities including neutron and charged particle irradiation facilities were complementarily used. Here, the initial focus of the Joint Projects was on fundamental fusion neutron radiation effects and irradiation correlation. Systematic comparison of fission and fusion radiation effects in comparable damage levels and the effects of transmutation-induced helium were investigated. The collaboration was then focused on the effect of dynamic irradiation effects in variable conditions. In addition to the relatively fundamental studies, the Joint Projects contributed largely to development of candidate materials such as RAFM steels, vanadium alloys, SiC/SiC composites, and tungsten alloys, through a mechanism-oriented approach. The Joint Projects also covered issues specific to materials application to fusion blankets and plasma-facing components, including neutron radiation effects such as tritium retention and permeation of neutron-irradiated plasma-facing materials. Various irradiation technologies were developed and applied to the irradiation experiments, including those for in-situ testing.Considering that high energy neutron sources, such as A-FNS and IFMIF-DONES, now have high viability, the research supporting the neutron source programs is essential. The knowledge obtained through the Joint Projects is valuable and should be advanced for this purpose. To this end, it is of urgent necessity to launch an international scientific program accumulating knowledge of fusion neutron radiation effects, including their fundamental aspects.

36 MATERIALS SCIENCE↗

Achieving record hot spot energies with large HDC implosions on NIF in HYBRID-E

HYBRID-E is an inertial confinement fusion implosion design that increases energy coupled to the hot spot by increasing the capsule scale in cylindrical hohlraums while operating within the current experimental limits of the National Ignition Facility. HYBRID-E reduces the hohlraum scale at a fixed capsule size compared to previous HYBRID designs, thereby increasing the hohlraum efficiency and energy coupled to the capsule, and uses the cross-beam energy transfer (CBET) to control the implosion symmetry by operating the inner (23° and 30°) and outer (44° and 50°) laser beams at different wavelengths (Δλ> 0). Small case to capsule ratio designs can suffer from insufficient drive at the waist of the hohlraum. We show that only a small amount of wavelength separation between the inner and outer beams (Δλ1-2 Å) is required to control the symmetry in low-gas-filled hohlraums (0.3 mg/cm3 He) with enough drive at the waist of the hohlraum to symmetrically drive capsules 1180 μm in outer radius. This campaign is the first to use the CBET to control the symmetry in 0.3 mg/cm3 He-filled hohlraums, the lowest gas fill density yet fielded with Δλ> 0. We find a stronger sensitivity of hot spot P2 in μm per Angstrom (40–50 μm/Å wavelength separation) than observed in high-gas-filled hohlraums and previous longer pulse designs that used a hohlraum gas fill density of 0.6 mg/cm3. There is currently no indication of transfer roll-off with increasing Δλ, indicating that even longer pulses or larger capsules could be driven using the CBET in cylindrical hohlraums. We show that the radiation flux symmetry is well controlled during the foot of the pulse, and that the entire implosion can be tuned symmetrically in the presence of the CBET in this system, with low levels of laser backscatter out of the hohlraum and low levels of hot electron production from intense laser–plasma interactions. Radiation hydrodynamic simulations can accurately represent the early shock symmetry and be used as a design tool, but cannot predict the late-time radiation flux symmetry during the peak of the pulse, and semi-empirical models are used to design the experiments. Deuterium–tritium (DT)-layered tests of 1100 μm inner radius implosions showed performance close to expectations from simulations at velocities up to ~360 km/s, and record yields at this velocity, when increasing the DT fuel layer thickness to mitigate hydrodynamic mixing of the ablator into the hot spot as a result of defects in the ablator. However, when the implosion velocity was increased, mixing due to these defects impacted performance. The ratio of measured to simulated yield for these experiments was directly correlated with the level of observed mixing. These simulations suggest that reducing the mixing, e.g., by improving the capsule defects, could result in higher performance. In addition, future experiments are planned to reduce the coast time at this scale, delay between the peak compression and the end of the laser, to increase the hot spot convergence and pressure. To reduce the coast time by several hundred ps compared to the 1100 μm inner radius implosions, HYBRID-E has also fielded 1050 μm inner radius capsules, which resulted in higher hot spot pressure and a fusion energy yield of ~170 kJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Principal factors in performance of indirect-drive laser fusion experiments

Progress in inertial confinement fusion depends on the accurate interpretation of experiments that are complex and difficult to explain with simulations. Results could depend on small changes in the laser pulse or target or physics that are not fully understood or characterized. In this paper we discuss an x-ray-driven platform [K. Baker et al., Phys. Rev. Lett. 121, 135001 (2018)] with fewer sources of degradation, and find the fusion yield can be described as a physically motivated function of laser energy, target scale, and implosion symmetry. This platform and analysis could enable a more experimental approach to the study and optimization of implosion physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experiments to explore the influence of pulse shaping at the National Ignition Facility

The shaping of the drive pulse in time is a key tool in the design of fusion experiments that use inertia to confine burning plasmas. It is directly related to the adiabat and compressibility of the DT fuel, and the characteristics of the laser and target that are needed to ignite. With this in mind, we have performed experiments at the National Ignition Facility that test small changes in the shape of the pulse. In contrast to theory, we find implosions at lower adiabats can have reduced yield and areal density. We discuss implications to performance and the mechanism(s) that could be responsible.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurements of effective actinides neutron capture cross sections in a cadmium-filtered epithermal neutron spectrum

In this work, a total of 20 actinide samples were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL): 233 U (1), 235 U (1), 236 U (1), 238 U (1), 237 Np (2), 239 Pu (1), 240 Pu (1), 242 Pu (2), 244 Pu (2), 241 Am (2), 243 Am (2), 244 Cm (2), and 248 Cm (2). The samples were loaded in a basket containing a 1.1-mm thick cadmium filter. The presence of the filter drastically changes the neutron spectrum in the samples and accentuates the reaction rates in the resonance region. Isotopic ratios were determined using Multi-Collector Inductively Coupled Plasma Mass Spectrometry (MC-ICP-MS) that allowed inferring effective capture cross sections. Detailed best-estimate MCNP models of the experiment using ENDF/B-VII.0 nuclear data were developed to calculate the effective neutron cross sections and, subsequently, compare them with the cross sections inferred from experimental results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Record Energetics for an Inertial Fusion Implosion at NIF

Inertial confinement fusion seeks to create burning plasma conditions in a spherical capsule implosion, which requires efficiently absorbing the driver energy in the capsule, transferring that energy into kinetic energy of the imploding DT fuel and then into internal energy of the fuel at stagnation. In this work, we report new implosions conducted on the National Ignition Facility (NIF) with several improvements on recent work [Phys. Rev. Lett. 120, 245003 (2018); Phys. Rev. E 102, 023210 (2020)]: larger capsules, thicker fuel layers to mitigate fuel-ablator mix, and new symmetry control via cross-beam energy transfer; at modest velocities, these experiments achieve record values for the implosion energetics figures of merit as well as fusion yield for a NIF experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Understanding asymmetries using integrated simulations of capsule implosions in low gas-fill hohlraums at the National Ignition Facility

Current capsule implosions at the National Ignition Facility (NIF) using high-density-carbon ablators and laser energies close to 2 MJ have shown neutron yields in excess of 50 kJ. Improving on this performance requires understanding of the different degradation mechanisms. For many NIF implosions, nuclear diagnostic signatures have inferred residual hot-spot velocities that correlate with fuel areal density variations consistent with a low-order mode-1 asymmetry. A current working hypothesis attributes these asymmetries to a combination of beam to beam variations in the laser delivery and possibly coupling to target features, such as the diagnostic holes needed for x-ray imaging. Recently, a new source has been identified, thickness variation in the ablator shell. To gain better understanding and eventually mitigate the causes of <ρR> asymmetries, 3D integrated simulations using the actual delivered laser powers are needed. To capture the effect of the diagnostic holes (DHs) using direct numerical simulation would require significantly large computational resources. Instead, our 3D simulations make use of a subgrid model developed using highly-resolved 2D simulations that include several details of the DH engineering complexity. Simulations of NIF shots using hohlraums without DHs, to isolate the effect of beam-to-beam variations, reproduce fairly well the observed nuclear diagnostic signatures. Similarly, reasonable agreement between data and simulations is also obtained in the presence of diagnostic holes. To account for the remaining discrepancies a sensitivity study of ablator thickness variation showed that 1% thickness asymmetries are comparable in effect to 1% peak drive mode-1 asymmetries. Furthermore, this study identified sensitivity to variations in the imbedded doped layer (needed to shield the DT ice from the high energy x-rays generated in the hohlraum) thickness even when the inner and outer surface of the ablator are perfectly spherical.

radiation hydrodynamics↗

Principal factors in performance of indirect-drive laser fusion experiments

Progress in inertial confinement fusion depends on the accurate interpretation of experiments that are complex and difficult to explain with simulations. Results could depend on small changes in the laser pulse or target or physics that are not fully understood or characterized. In this paper we discuss an x-ray-driven platform with fewer sources of degradation, and find the fusion yield can be described as a physically motivated function of laser energy, target scale, and implosion symmetry. Furthermore, this platform and analysis could enable a more experimental approach to the study and optimization of implosion physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experiments to explore the influence of pulse shaping at the National Ignition Facility

The shaping of the drive pulse in time is a key tool in the design of fusion experiments that use inertia to confine burning plasmas. Here, it is directly related to the adiabat and compressibility of the DT fuel, and the characteristics of the laser and target that are needed to ignite. With this in mind, we have performed experiments at the National Ignition Facility that test small changes in the shape of the pulse. In contrast to theory, we find implosions at lower adiabats can have reduced yield and areal density. We discuss implications to performance and the mechanism(s) that could be responsible.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Deficiencies in compression and yield in x-ray-driven implosions

This paper analyzes x-ray–driven implosions that are designed to be less sensitive to 2-D and 3-D effects in hohlraum and capsule physics. Key performance metrics including the burn-averaged ion temperature, hot-spot areal density, and fusion yield are found to agree with simulations where the design adiabat (internal pressure) is multiplied by a factor of 1.4. Furthermore, these results motivate the development of a simple model for interpreting experimental data, which is then used to quantify how improvements in compression could help achieve ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurements of enhanced performance in an indirect drive inertial confinement fusion experiment when reducing the contact area of the capsule support

Experimental results from indirectly driven inertial confinement fusion experiments testing the performance gained from using an alternate capsule tent support are reported. The polar tent describes an alternate geometry for the thin membrane used to support the Deuterium–Tritium (DT) filled capsule. In this work, the contact area is reduced by 23 times by locating the tent support close to the poles of the capsule. The polar tent experiments are repeats of previous 3 shock 1.63 MJ, 400 TW high foot experiments and use a 165 μm thick silicon doped carbon hydrogen plastic (CH) shell. Using the polar tent support, we report a DT neutron yield of 1.07 ×1016, 76% higher than the expected Y DT ∝V 7.7 scaling. This is, at the time of writing, the highest neutron yield to date from a CH shell implosion. Furthermore, we find that the inferred pressure when using the polar tent is significantly above the model based on analytic scaling even when accounting for tent effects. Analysis of x-ray and neutron images shows the reduction of lobes produced by nominal tent features. The reduction of these features in the polar tent experiments leads to decreased low mode (P2 and P4) asymmetry compared to the nominal tent results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hot-spot mix in large-scale HDC implosions at NIF

Mix of high-Z material from the capsule into the fuel can severely degrade the performance of inertial fusion implosions. On the Hybrid B campaign, testing the largest high-density-carbon capsules yet fielded at the National Ignition Facility, several shots show signatures of high levels of hot-spot mix. We attribute a ~40% yield degradation on these shots to the hot-spot mix, comparable to the level of degradation from large $P_2$ asymmetries observed on some shots. Additionally, a range of instability growth factors and diamond crystallinity were tested and they do not determine the level of mix for these implosions, which is instead set by the capsule quality.

Fusion experiments↗