Incorrect resonance escape probability in Monte Carlo codes due to the threshold approximation of temperature-dependent scattering
Not Available
Engineering topics
Publications and source records attributed to Clarno, Kevin.
Not Available
A coupled physics problem consisting of radiation transport and heat transfer was modeled using COMSOL Multiphysics to simulate a criticality accident. Reduced order models (ROM) were created to accelerate the radiation transport calculation through Proper Orthogonal Decomposition (POD). Additionally, on-the-fly neutron cross sections were generated from a non-linear function through a feed forward neural network. The Livelink for MATLAB module allowed for data transfer between an otherwise independent solver and in-house modules. A data driven approach to POD was developed to act as a surrogate model to couple with heat transfer, with the POD module written in MATLAB coupled to an isolated heat transfer solve in COMSOL. A coupled transient solution resulted in a good approximation of the flux and temperature, with the maximum error being 3E-2 and 2.5E-3 respectively.
CTF is a thermal hydraulic (T/H) subchannel tool that has been extensively developed over the past ten years as part of the Consortium for Advanced Simulation of Light Water Reactors (CASL) program. The code was selected early in the CASL program for support of high-impact challenge problems that were found to be relevant to the nuclear industry and its currently operating fleet of pressurized water reactors (PWRs), including issues such as departure from nucleate boiling (DNB), crud-induced power shifts (CIPSs), and reactivity-insertion accidents (RIAs). By incorporating CTF into the multiphysics Virtual Environment for Reactor Application (VERA) core simulator software developed by CASL, CTF has become the primary means of providing fluid and fuel thermal feedback, as well as T/H figure-of-merits (FOMs) in large-scale reactor simulations. With the goal of solving industry challenge problems, CASL placed great emphasis on developing high-quality, high-performance, validated software tools that offer higher fidelity than what is currently possible with current industry methods. In support of this effort, CTF was developed from a research tool into an nuclear quality assurance (NQA-1)–compliant, production-level software tool that is capable of addressing the stated challenge problems and goals of CASL. This work presents a review of the major technological achievements that were realized in developing CTF over the past decade of the CASL program and presents an overview of the code solution approach and closure models.
As the core simulator capabilities in the Virtual Environment for Reactor Applications (VERA) have become more mature and stable, increased attention has been focused on coupling Bison to provide fuel performance simulations. This technique has been a very important driver for the pellet-clad interaction challenge problem being addressed by the Consortium for Advanced Simulation of Light Water Reactors (CASL). Here, two coupling approaches are demonstrated on quarter core problems based on Watts Bar Nuclear Plant Unit 1, Cycle 1: (1) an inline approach in which a one-way coupling is used between neutronics/thermal hydraulics (through MPACT/CTF) and fuel performance (through Bison) but no fuel temperature information is passed back to MPACT/CTF, and (2) a two-way approach (coupled) in which the fuel temperature is passed from Bison to MPACT/CTF. In both approaches, power and temperature distributions from MPACT/CTF are used to inform the Bison simulations for each rod in the core.The demonstrations presented here are the first integrated fuel performance simulations in VERA, which opens many possibilities for future work, including applications to accident-tolerant fuel efforts and transient simulations, which are of critical importance to CASL. These demonstrations also highlight the potential to move away from the current Bison-informed fuel temperature lookup table approach, which is the default in MPACT/CTF simulations, if performance improvements are made in the near future.
Explore the source record for details and available documents.
It is important to be able to accurately predict the neutron flux outside the immediate reactor core for a variety of safety and material analyses. Monte Carlo radiation transport calculations are required to produce these high–fidelity ex-core responses. The Virtual Environment for Reactor Applications (VERA) provides the automated capability to launch independent Shift fixed-source and eigenvalue Monte Carlo (MC) calculations for user-specified state points during a standard Virtual Environment for Reactor Applications (VERA) calculation. VERA couples MPACT with COBRA-TF (CTF) to Shift to perform ex-core tallies for multiple state points concurrently, with each component capable of parallel execution on independent processor domains. In these ex-core calculations, MPACT is coupled to CTF and performs the in-core depletion and heat transfer calculation, followed by a fixed-source Shift transport calculation including ex-core regions to produce ex-core responses. The fission source, fuel pin temperatures, moderator temperature and density, boron concentration, and fuel pin depleted isotopic compositions can be transferred to Shift from the MPACT calculation. Specifically, VERA performs fluence calculations in the core barrel outward to the end of the pressure vessel and detector response calculations in ex-core detectors. It also performs the requested tallies in any user-defined ex-core regions. VERA takes advantage of the General Geometry (GG) package in Shift. This gives VERA the flexibility to explicitly model features outside the core barrel, including detailed vessel models, detectors, and power plant details. A very limited set of experimental and numerical benchmarks is available for ex-core simulation comparison. The Consortium for Advanced Simulation of Light Water Reactors has developed a set of ex-core benchmark problems to include as part of the VERA verification and validation set of problems. The ex-core capability in VERA has been tested on small representative assembly problems, multi-assembly problems, as well as quarter-core and full-core problems. VERA View has also been extended to visualize these vessel fluence results from VERA. This manual serves to present a guide to VERA users about the methodology behind ex-core calculations and the details of input, output, and analysis of results from these calculations. Details in this version of the manual are based on features in VERA 4.0.1.
The Virtual Environment for Reactor Applications (VERA) Infrastructure provides the infrastructure to build, configure, test, install, and package for release the VERAS suite of codes that is being developed by the Consortium for the Advanced Simulation of Light-water reactors (CASL). It includes the list of codes that can be built within VERA, the location on the configuration-controlled CASL development computer, the version number used in any particular software installation, the location of the third-party libraries used for testing VERA on a suite of the CASL testing and development computers, and the scripts to configure, build, test, install, and package for release a particular version of VERA. The VERA Infrastructure contains a list of scripts, configuration options, and utilities that are specific to CASL, but contain no physics or numeric, nuclear technology, or encryption technology.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
The Consortium for Advanced Simulation of Light Water Reactors (CASL) aims to provide high-fidelity multiphysics simulations of light water nuclear reactors. To accomplish this, CASL is developing the Virtual Environment for Reactor Applications (VERA), which is a suite of code packages for thermal hydraulics, neutron transport, fuel performance, and coolant chemistry. As VERA continues to grow and expand, there has been an increased focus on incorporating fuel performance analysis methods. One of the primary goals of CASL is to estimate local cladding failure probability through pellet-clad interaction, which consists of both pellet-clad mechanical interaction (PCMI) and stress corrosion cracking. Estimating clad failure is important to preventing release of fission products to the primary system and accurate estimates could prove useful in establishing less conservative power ramp rates or when considering load-follow operations.While this capability is being pursued through several different approaches, the procedure presented in this article focuses on running independent fuel performance calculations with BISON using a file-based one-way coupling based on multicycle output data from high fidelity, pin-resolved coupled neutron transport–thermal hydraulics simulations. This type of approach is consistent with traditional fuel performance analysis methods, which are typically separate from core simulation analyses. A more tightly coupled approach is currently being developed, which is the ultimate target application in CASL.Recent work simulating 12 cycles of Watts Bar Unit 1 with VERA core simulator are capitalized upon, and quarter-core BISON results for parameters of interest to PCMI (maximum centerline fuel temperature, maximum clad hoop stress, and minimum gap size) are presented for Cycles 1–3. In conclusion, based on these results, this capability demonstrates its value and how it could be used as a screening tool for gathering insight into PCMI, singling out limiting rods for further, more detailed analysis.
This milestone report documents work performed in CASL that was broadly focused on the use of validated high-fidelity simulation codes to inform, improve and calibrate low-fidelity codes to facilitate multiphysics coupling, design, performance analysis, and risk assessment. This high-to-low (Hi2Lo) initiative has the following objectives: employ physics encapsulated in high-fidelity codes to improve the functionality of low-fidelity codes, quantify biases in low-fidelity codes, develop and calibrate physical models and closure relations so that low-fidelity codes more accurately incorporate requisite physics, and develop low-fidelity codes that can be effectively coupled to simulate multiphysics behavior. In combination, these efforts are designed to impact both CIPS and DNB. For example, the development and experimental design-based Bayesian calibration of dynamic gas conductance models in CTFFuel will provide the capability to better model crud-induced power shifts. Whereas the present emphasis has focused on the high-fidelity codes STAR-CCM+ and BISON and low-fidelity codes CTF and CTFFuel, future emphasis will be expanded to include MAMBA. During the reporting period, Hi2Lo efforts focused on two broad components: demonstration of the experimental design-based Bayesian calibration framework to calibrate CTF using both STAR-generated synthetic data and experimental data, and the use of STAR to inform and improve the turbulence modeling and grid heat transfer modeling capabilities in CTF. A complementary milestone focused on the implementation and verification of fuel models in CTFFuel, for which we demonstrated initial calibration results. Future Hi2Lo work will focus on the use of the experimental design-based Bayesian calibration framework, demonstrated this year for STAR and CTF, to calibrate parameters in the fuel swelling, fuel irradiation-induced densification, and fuel relocation models in CTFFuel using both experimental and BISON-generated data. A second component will focus on the continued use of STAR to improve grid modeling capabilities in CTF.
Not Available
This report describes the creation a lightweight Docker image with a working installation of the VERA simulation components for CASL.
This milestone report documents an approach that seeks to develop a standalone fuel solver to simulate steady-state and transient thermo-mechanical responses of light-water reactor fuel rods and assess its temperature predictions against analytical solutions, and a well-known and validated fuel performance code. This manuscript focuses on five major topics: (1) development of the CTFFuel, (2) discussion of the newly implemented fuel deformation models in dynamic gap conductance model of CTFFuel, (3) enabling the dynamic gap conductance model in VERA-CS, (4) verification of the solid conduction solution and comparison of the CTFFuel with respect to the workhorse code, CTF, and (5) benchmark of the thermal conductivity degradation using the burnup dependent fuel thermal conductivity models and benchmark of the fuel centerline temperature using the dynamic gap conductance model with Halden measurements and FRAPCON-4.0 simulation results. CTFFuel temperature predictions are compared to predictions from FRAPCON-4.0 for UO 2 , UO 2 +Gd 2 O 3 and MOX fuels through reactor’s life. The main motivation is to understand discrepancies between CTFFuel and FRAPCON-4.0’s temperature predictions.
Explore the source record for details and available documents.
As part of the Consortium for Advanced Simulation of Light Water Reactors (CASL), the Virtual Environment for Reactor Applications (VERA) is being developed to provide high-fidelity multiphysics simulations of nuclear reactor cores. Over the past year, a one-way coupling capability has been developed, taking power and temperature data from MPACT/CTF calculations and running standalone BISON fuel rod cases. This has allowed CASL contributors to gain insight into the fuel performance characteristics while a more tightly coupled methodology between MPACT, CTF, and BISON has been under development. Many of the initial analyses have focused on the Watts Bar Unit 1 core using a fast flux factor—the default approach—which defines the clad fast flux as a linear function of the local linear heat rate. While this approach is more valid when considering single rod cases in isolation, in larger problems such as full-sized reactors, the local linear heat rate does not directly correlate to the clad fast neutron flux. For example, variations in assembly enrichment can lead to larger neutron fluxes in neighboring assemblies that may be at lower enrichment and power. Similarly, considering axial effects, spacer grids suppress power locally, but the fast neutron flux is significantly less affected, and the approach can lead to an underestimation of the fast neutron flux at that time. A poor estimation of the clad fast flux values can affect the clad creep rate, fuel-clad gap, and clad stresses. Additionally, the fast flux factor has been considered constant throughout the life of the rod. As the cycle progresses, the spectrum will harden as burnable absorbers and 235U deplete, so the fast flux would be expected to increase as the spectrum hardens. The effect on quantities of interest are highlighted for the first cycle of the Watts Bar Unit 1 core, comparing the results from an explicit clad fast flux representation from MPACT to the constant fast flux factor approach used in previous analyses. Future work will consider multicycle effects to assess the impact at higher burnups.
This report corresponds to milestone L3:PHI.PCI.P15.03, which was originally intended to investigate the time discretization approaches with the newly developed fully coupled Tiamat capability, targeting single assembly problems. At the time, it was thought that various time discretization approaches would need to be assessed. However, it was decided that this was not necessary as what is currently implemented in the code is adequate to provide consistent and full coupling between MPACT, CTF, ORIGEN, and Bison. As such, the milestone has effectively been repurposed as a stepping stone to the quarter core demonstration milestone slated for completion in August by describing and demonstrating the new fully coupled Tiamat capability on a single assembly case based on VERA Progression Problem 6, but with the addition of depletion throughout a representative cycle. Additionally, several other contributions that have been critical to this demonstration are also described. These include (1) the 1.5D capability developed by the Bison team, (2) improvements to the burnup representation in Bison through Tiamat, and (3) the additions to MOOSE to allow Bison to resolve the same timestep are also discussed. Initial simulations have been performed for the Watts Bar Unit 1 Cycle 1 with fully coupled Tiamat. While there are a few things to be improved for the final simulations, the initial results look very promising. The current status and results from this will be presented here, as well as the path forward to resolve the issues observed.