In-Situ Monitoring of Microstructural Features in PuGa Alloys at Non-Ambient Conditions
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Clausen, Bjorn.
Explore the source record for details and available documents.
Microstructure-aware models are necessary to predict the behavior of material based on process knowledge or to extrapolate mechanical properties of materials to environmental conditions which are not easily reproduced in the laboratory, e.g., nuclear reactor environments. Elemental Ta provides a relatively simple BCC system in which to develop a microstructural understanding of deformation processes which can then be applied to more complicated BCC alloys. In situ neutron diffraction during compressive deformation and subsequent heat treatment have been used to monitor the evolution of microstructural features in Ta throughout simulated processing steps. Crystallographic texture and dislocation density are determined as a function of first plastic strain, then temperature. Lattice strains are determined and attributed to stresses at macroscopic, grain and dislocation length scales. The increase of the dislocation density through deformation and subsequent recovery during heat treatment is monitored through the changing diffraction line profile. Also, randomization of the texture is used as a signature of recrystallization. The recovery of dislocations through annihilation is not observed to depend on the initial dislocation density in the range studied here. In contrast, recrystallization is observed to depend strongly on the initially dislocation density.
X-ray diffraction patterns contain information about the atomistic structure and microstructure (defect population) of materials, extracting detailed information from diffraction patterns is complex, demanding and relies on prior knowledge. Here, we hypothesize that deep-learning techniques can help to perform an effective and accurate analysis with high throughput rates. To demonstrate this concept, we applied a novel deep learning framework to determine the evolution of the β-phase volume fraction in a Ti–6Al–4V alloy during heat-treatment from video sequences of 2D diffraction patterns recorded in transmission and with highly monochromatic radiation in a synchrotron beamline. In particular, we studied the impact of network design on prediction reliability and computational performance. Networks of different architectures were trained using 3008 experimental 2D patterns. A well-tuned model was found to reproduce the phase fractions of another experimental data set, consisting of 1100 diffraction patterns, with a mean-square error as small as 2.6 x 10 -4 . The average prediction error of β-phase volume fraction was within 1.6 x 10 -2 (in each diffraction pattern) of the values obtained by conventional methods. Our work demonstrates that convolutional neural networks can evaluate high energy X-ray diffraction patterns with a remarkable level of reliability. Furthermore, it demonstrates the significance of network design on the reliability of predictions and computational performance. The most complex models do not necessarily result in highest accuracy and may even fail to learn from the data.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
The LANSCE accelerator complex exploits a flexible, high power 800 MeV proton linear accelerator to enable a broad swath of experimental work supporting multiple scientific programs. The beam requirements for these programs are diverse and change over time. The purpose of this document is to record, at a high level, the experimental requirements driving the beam delivery requirements for each experimental facility at LANSCE. Revision 0 serves to baseline the current set of experiments, and we expect to revise the document on an as-needed basis when either the experimental requirements change or are found to require a more complete definition.
Not Available
Abstract not provided.
Abstract Non-destructive evaluation of plastically deformed metals, particularly diffraction line profile analysis (DLPA), is valuable both to estimate dislocation densities and arrangements and to validate microstructure-aware constitutive models. To date, the interpretation of whole line diffraction profiles relies on the use of semi-analytical models such as the extended convolutional multiple whole profile (eCMWP) method. This study introduces and validates two data-driven DLPA models to extract dislocation densities from experimentally gathered whole line diffraction profiles. Using two distinct virtual diffraction models accounting for both strain and instrument induced broadening, a database of virtual diffraction whole line profiles of Ta single crystals is generated using discrete dislocation dynamics. The databases are mined to create Gaussian process regression-based surrogate models, allowing dislocation densities to be extracted from experimental profiles. The method is validated against 11 experimentally gathered whole line diffraction profiles from plastically deformed Ta polycrystals. The newly proposed model predicts dislocation densities consistent with estimates from eCMWP. Advantageously, this data driven LPA model can distinguish broadening originating from the instrument and from the dislocation content even at low dislocation densities. Finally, the data-driven model is used to explore the effect of heterogeneous dislocation densities in microstructures containing grains, which may lead to more accurate data-driven predictions of dislocation density in plastically deformed polycrystals.
In-situ high energy x-ray scattering experiments enable high temporal resolution investigations of precipitation kinetics; Continuous and discontinuous precipitation are competitive near the TTT nose (~525°C); The incubation time for discontinuous precipitation increases significantly at temperatures below the TTT nose; Additional evidence for the divergent interlamellar spacing was observed at 434°C and 466°C
During the laser-powder bed fusion (L-PBF) process, high laser intensities, short interaction times and highly localized heat input drive large thermal gradients that result in a state of high residual stresses. Generally, the residual stresses that develop during the L-PBF process can compromise the performance of the component. Up to now, the literature has indicated that the magnitude of the residual stresses can be affected by various process parameters. In this study, all process parameters such as laser power and speed are held fixed and the focus is solely on the effect of the laser scan strategy on the three-dimensional residual stress state of L-PBF metallic components. Four Ti-6Al-4V bridge shaped components were built using island and continuous scanning patterns parallel and offset 45° from the sample axes. High-energy X-ray diffraction was used to determine the residual stress field in each of the components. Two of them were re-measured after being partially removed from the build plate. The assumptions implicit in diffraction measurements of stress are reviewed and discussed in depth because the unique microstructure associated with L-PBF Ti-6Al-4V renders the validity of those assumptions uncertain. Specifically, additional data was collected and analyzed to evaluate the relationship between grain scale and macroscopic scale stresses. The observed residual stresses were large, ½ to ¾ of the yield strength, particularly the build direction stresses near the lateral edges of the bridges. Here in this work, the higher stresses were observed in the bridges built via the island scan strategies, chiefly near the edges of the parts.
In-situ Synchrotron X-ray Scattering to Determine the TTT Diagram of U-6Nb
Explore the source record for details and available documents.
Several mechanical and thermophysical properties are required as a function of non-stoichiometry for the successful implementation of YH 2-x for nuclear reactor moderator applications. Density functional theory calculations, in combination with neutron diffraction experiments, were used to study the structural and mechanical properties of YH 2-x . Point defect analysis indicated H occupation primarily at the tetrahedral site within an fcc Y sub-lattice, confirming a fluorite YH 2 structure. The small positive formation energy for H vacancies under Y-rich conditions predicted that hypo-stoichiometry is accommodated by Y+YH 2 at ambient conditions and by H vacancies in the YH 2-x single phase that is relevant to high temperatures. Neutron diffraction studies were used to confirm both the occupation of H on tetrahedral sites and the near-stoichiometric composition of the hydride phase in the two-phase Y+YH 2 region of the phase diagram that dominates at room temperature. Energy minimized special-quasirandom-structures of H vacancies were used to calculate lattice parameters, elastic constants, and several other properties as a function of composition for the single phase YH 2-x . The lattice parameter of YH 2-x decreased by only 0.004 Å with increasing H/Y for the range 1.31 ≤ H / Y ≤ 2.0 indicating a negligible effect on lattice parameters due to vacancy formation. In the two-phase region, however, calculations predicted the density of z Y + ( 1 - z ) Y H 2 - x to increase with decreasing H/Y at lower temperatures due to the increased fraction of high-density Y metal. Additionally, for the high temperature single phase, decreasing H/Y reduced the density as a consequence of the lattice expansion associated with vacancy formation. All elastic constants and moduli increased with increasing hydrogen content in single-phase YH 2-x .
HExploring the effects of minor ternary alloying additions, typically impurity elements, on the phase stability of U-10Mo is important for preventing undesirable phase decomposition during processing or during service. This work examines the influence small ternary additions of Cr, Ni, and Co. Both in-situ and ex-situ neutron diffraction measurements made during and after high temperature (450 – 525°C) exposures were used to better define the influence of these elements on the time-temperature-transformation (TTT) behavior of U-10Mo, providing information which is complementary to electron microscopy investigations of the same alloy systems performed in the first part of this work. Minor additions of Ni and Co decrease the ?-phase stability at all temperatures investigated. Signatures of U6X (X = Ni or Co) compounds were shown to be present in amounts of up to 6 wt% in the heat treated alloys, suggesting that the initial precipitation of this phase may catalyze further ?-phase decomposition. On the other hand, the Cr containing alloys were observed to have nearly the same, and in some cases slower, phase transformation kinetics when compared to the binary U-10Mo control samples. The results of the study have enabled preliminary estimates of the TTT curves for the ternary alloys.
Steels are ubiquitous due to their affordability and the landscape of useful properties that can be generated for engineering applications. But to further expand the performance envelope, one must be able to understand and control microstructure development by alloying and processing. In this paper we use multiscale, advanced characterization to better understand the structural and chemical evolution of AISI 4340 steel after quenching and tempering (Q&T), including the role of quench rate and short-time, isothermal tempering below 573 K (300 °C), with an emphasis on carbide formation. We compare the microstructure and/or property changes produced by conventional tempering to those produced by higher temperature, short-time “rapid” tempering. We underscore that no single characterization technique can fully capture the subtle microstructure changes like carbon redistribution, transition carbide and/or cementite formation, and retained austenite decomposition that occur during Q&T. Only the use of multiple techniques begins to unravel these complexities. After controlled fast or slow quenching, η transition carbides clearly exist in the microstructure, likely associated with autotempering of this high martensite start temperature (Ms) steel. Isothermal tempering below 598 K (325 °C) results in the relief of carbon supersaturation in the martensite, primarily by the formation of η transition carbides that exhibit a range of carbon levels, seemingly without substitutional element partitioning between the carbide and matrix phases. Hägg transition carbide is present between 300 °C and 325 °C. After conventional tempering at or above 598 K (325 °C) for 2 h, cementite is predominant, but small amounts of cementite are also present in other conditions, even after quenching. Previous work has indicated that silicon (Si) and substitutional elements partition between the cementite, which initially forms under paraequilibrium conditions, and the matrix. Phosphorous (P) may also be preferentially located at cementite/matrix interfaces after high temperature tempering. Slower quench rates result in greater amounts of retained austenite compared to those after fast quenching, which we attribute to increased austenite stability resulting from “autopartitioning”. Rapid, high temperature tempering is also found to diminish tempered martensite embrittlement (TME) believed to be associated with the extent of austenite decomposition, resulting in mechanical properties not attainable by conventional tempering, which may have important implications with respect to industrial heat treatment processes like induction tempering. Controlling the amount and stability of retained austenite is not only relevant to the properties of Q&T steels, but also next-generation advanced high strength steels (AHSS) with austenite/martensite mixtures.
Residual stress measurements using neutron diffraction and the contour method were performed on a valve housing made from 316 L stainless steel powder with intricate three-dimensional internal features using laser powder-bed fusion additive manufacturing. The measurements captured the evolution of the residual stress fields from a state where the valve housing was attached to the base plate to a state where the housing was cut free from the base plate. Making use of this cut, thus making it a non-destructive measurement in this application, the contour method mapped the residual stress component normal to the cut plane (this stress field is completely relieved by cutting) over the whole cut plane, as well as the change in all stresses in the entire housing due to the cut. The non-destructive nature of the neutron diffraction measurements enabled measurements of residual stress at various points in the build prior to cutting and again after cutting. Good agreement was observed between the two measurement techniques, which showed large, tensile build-direction residual stresses in the outer regions of the housing. The contour results showed large changes in multiple stress components upon removal of the build from the base plate in two distinct regions: near the plane where the build was cut free from the base plate and near the internal features that act as stress concentrators. These observations should be useful in understanding the driving mechanisms for builds cracking near the base plate and to identify regions of concern for structural integrity. Neutron diffraction measurements were also used to show the shear stresses near the base plate were significantly lower than normal stresses, an important assumption for the contour method because of the asymmetric cut.
We discuss a simple statistical analysis which yields the precision, resolution, accuracy and trueness of diffraction-based lattice strain measurements. The procedure consists of measuring the thermal expansion induced in each component of an ideal, non-reacting, two-component, crystalline powder sample in situ. One component, with a high coefficient of thermal expansion (CTE), serves as an internal thermometer. The quantities of interest are obtained by determining the smallest, statistically significant, thermal lattice strain which can be detected through diffraction analysis in the second, low CTE, component in response to controlled temperature changes. This procedure also provides a robust check of the alignment of the diffraction system and is able to reveal the presence of systematic errors. The application of this technique to a time-of-flight engineering diffractometer/strain scanner is presented.