Engineering topics

Clelland, Dustin T.

Publications and source records attributed to Clelland, Dustin T..

5 records

DOE OSTI2024

An in-situ view cell system for investigating swelling behavior of elastomers upon high-pressure hydrogen exposure

The transition to hydrogen as a clean and efficient energy carrier is impeded by challenges in the compatibility of hydrogen with materials used within hydrogen infrastructure. Elastomers, crucial in sealing components, often exhibit premature failures in high-pressure hydrogen environments due to excessive swelling. This study employs an innovative in-situ view cell system to assess the swelling behavior of hydrogenated nitrile butadiene rubber (HNBR) under various hydrogen conditions. The system, designed to withstand pressures up to 96.5 MPa, incorporates Digital Image Correlation (DIC) for strain measurements and volume estimation. Results reveal non-linear volume increases during depressurization, challenging conventional assumptions. Furthermore, investigations into peak hydrogen pressures and pressure-holding scenarios during decompression highlight complex swelling trends. The introduction of a novel computer vision (CV) method enhances precision in volume estimation, overcoming DIC limitations. The study provides insights into mitigating elastomer swelling, crucial for developing robust materials to support future hydrogen-driven energy systems.

Elastomer↗

DOE OSTI2023

Direct measurement and calculation of rubber bulk modulus by piston-cylinder method using conventional mechanical testing equipment

This article describes a method to directly measure the bulk modulus of rubber using a piston-cylinder type apparatus. The function of the testing apparatus is to reliably transfer load to the water inside the vessel and allow for the accurate and continuous measurement of volumetric displacement as the contents are compressed. During the test, load is applied to a piston-cylinder containing the rubber test sample and water using a conventional mechanical testing load frame. Load and the travel of the piston are recorded by a load cell and extensometer, respectfully. A brass or stainless steel plug of the same dimensions as the test sample is tested as a control sample to isolate the compliance of the system, including the compressibility of water and compliance of the piston-cylinder. The results from this control test are used to disincorporate the compliance of the system from the sample test results. Load-linear displacement data are mathematically converted to pressure-volumetric displacement data, from which bulk modulus is calculated. The test apparatus and method are validated using the known bulk modulus of water. Finally, the bulk modulus for two similar rubbers is evaluated. The validity of the results and limitations of the device are discussed.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Forming Complex Nuclear Fuel Shapes in High-Loaded Silicide Surrogates

This work provides proof of the concept that high silicide loading nuclear fuel meat surrogates with complicated geometries can be produced with uniform density through an application of cold isostatic pressing (CIP). Dispersion fuels with high volumetric loading of U_3 Si_2 have challenges in fabrication. Fabrication involves a series of processes including powder compaction, rolling pack assembly, and roll forming. PNNL has undertaken extensive experimental work using MoSi2 and WSi2 as surrogates for U3Si2 to explore the feasibility of reducing or eliminating the issues through the application of CIP in the powder pressing step prior to rolling pack assembly. The composites were prepared at >40 vol% silicide loading, which was representative of 4.8 gU/cm^3 and formed via CIP at 50 KSI (Kilopound per Square Inch) pressure. The CIP mold design was taken through a design process which aimed to reduce defects and increase precision. The application of CIP here provides a broad strategy for producing highly loaded dispersion fuels with complex geometries and uniform density.

Clelland, Dustin T.↗

DOE OSTI2021

Joining Light Metals with Polymer Composites Through Metal Overcasting

This work investigates a unique technique to join aluminum (Al) and magnesium (Mg) alloys to carbon fiber reinforced polymer (CFRP) composites without the use of adhesives or mechanical fasteners. The joints were made using an overcasting technique where the molten alloys were cast around the polymer composites using high pressure die casting method. Rapid cooling during casting allowed the composite to be embedded inside the cast metal without causing any gross damage to the former even though the molten metal temperature exceeded the melting point of the composite matrix by several 100’s of deg. C. The metal/composite interface was examined using optical microscopy and x-ray imaging and the joint strength was examined through tensile testing. Although evidence of polymer melting was evident in the x-ray images, the embedded section of the composite coupons retained their overall shape and integrity. Preliminary tension tests on Al/CFRP composites showed strength degradation of the CFRP and it failed near the metal/CFRP interface (outside the joint). Strength degradation in the CFRP suggests that the overcasting process needs further optimization to minimize thermal excursion in the CFRP. Nevertheless, the overcasting process shows great promise as a unique joining technique with application in fabricating light-weight structures for automotive and transportation industries.

overcasting, Casting, Mg Castings, Al Casting, Joi↗

DOE OSTI2020

A Mechanical Test Frame for Property Evaluations at Cryogenic Temperature

On-board storage of hydrogen fuel has been designated as a limiting factor in the advancement of fuel cell technologies in the automotive industry. The use of cryo-compressed Type III pressure vessels presents one option to overcome this barrier. These multi-material vessels will be expected to perform at high pressure and extreme low temperatures, which creates a complex engineering design challenge. Many materials exhibit highly temperature-dependent properties, which must be considered for the efficient design of cryo-compressed pressure vessels. Complicating this issue, mechanical property data at cryogenic temperatures is sparse. This technical paper provides a description of a test apparatus commissioned specifically to help address this shortcoming. A mechanical test frame was retrofitted with a continuous flow cryostat capable to evaluate various mechanical properties throughout a broad temperature range of 25 °C to -269 °C with a load limit of 10 kN. An investigation of the thermomechanical properties of an epoxy resin was carried out as a demonstration.

Mechanical characterization, cryogenic pressure ve↗