Search NASA⌕ Search

Engineering topics

Cohen, D.

Publications and source records attributed to Cohen, D..

36 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Analysis of multifastener composite joints

A new numerical procedure for determining load proportioning in multiple-hole mechanical joints in composite plates is presented. The joints are loaded in double lap fashion in tension with pins through the holes. The commercial finite-element program ABAQUS is used to predict the load proportioning among holes using two independent plane stress finite-element models, one representing the composite inner lap and one representing the two steel outer laps, interacting through rigid circular surfaces. The circular surfaces effectively represent rigid pins. Load proportioning is predicted for a number of geometries. Excellent correlation with experimental data is obtained. Experimental and computed surface strains are also found to compare well. The assumption of a radial cosine distribution of contact stress between pin and hole is shown to be substantially in error for some holes.

Griffin, O. H., Jr.↗
NASA NTRS1988

Influence of geometric nonlinearities on skin-stiffener interface stresses

A method for computing skin-stiffener interface stresses in stiffened composite panels is developed. Both geometrically linear and nonlinear analyses are considered. Particular attention is given to the flange termination region where stresses are expected to exhibit unbounded characteristics. The method is based on a finite-element analysis and an elasticity solution. The results indicate that the inclusion of geometric nonlinearities is very important for an accurate determination of the interface stresses. Membrane flattening of the panel tends to reduce the tendency of the stiffener to separate.

Cohen, D.↗
NASA NTRS1986

Stresses and deformations in cross-ply composite tubes subjected to a uniform temperature change

This study investigates the effects of a uniform temperature change on the stresses and deformations of composite tubes and determines the accuracy of an approximate solution based on the principle of complementary virtual work. Interest centers on tube response away from the ends and so a planar elasticity approach is used. For the approximate solution a piecewise linear variation of stresses with the radial coordinate is assumed. The results from the approximate solution are compared with the elasticity solution. The stress predictions agree well, particularly peak interlaminar stresses. Surprisingly, the axial deformations also agree well, despite the fact that the deformations predicted by the approximate solution do not satisfy the interface displacement continuity conditions required by the elasticity solution. The study shows that the axial thermal expansion coefficient of tubes with a specific number of axial and circumferential layers depends on the stacking sequence. This is in contrast to classical lamination theory, which predicts that the expansion will be independent of the stacking arrangement. As expected, the sign and magnitude of the peak interlaminar stresses depend on stacking sequence. For tubes with a specific number of axial and circumferential layers, thermally induced interlaminar stresses can be controlled by altering stacking arrangement.

Hyer, M. W.↗
NASA NTRS1985

Stresses and deformations in cross-ply composite tubes subjected to a uniform temperature change: Elasticity and Approximate Solutions

The effects of a uniform temperature change on the stresses and deformations of composite tubes are investigated. The accuracy of an approximate solution based on the principle of complementary virtual work is determined. Interest centers on tube response away from the ends and so a planar elasticity approach is used. For the approximate solution a piecewise linear variation of stresses with the radial coordinate is assumed. The results from the approximate solution are compared with the elasticity solution. The stress predictions agree well, particularly peak interlaminar stresses. Surprisingly, the axial deformations also agree well. This, despite the fact that the deformations predicted by the approximate solution do not satisfy the interface displacement continuity conditions required by the elasticity solution. The study shows that the axial thermal expansion coefficient of tubes with a specific number of axial and circumferential layers depends on the stacking sequence. This is in contrast to classical lamination theory which predicts the expansion to be independent of the stacking arrangement. As expected, the sign and magnitude of the peak interlaminar stresses depends on stacking sequence.

Hyer, M. W.↗
NASA NTRS1985

Thermally induced stresses and deformations in layered composite tubes

The thermally induced stresses and deformations in layered, orthotropic tubes are studied. The motivation for studying tubes is their likely application for use in space structures. Tubes are a strong candidate for this application because of their high structural efficiency, as measured by stiffness per unit weight, and their relative ease of fabrication. Also, tubes have no free edges to deteriorate or delaminate. An anticipated thermal condition for tubes in space is a circumferential temperature gradient. This type of gradient will introduce dimensional changes into the structure and may cause stresses large enough to cause damage to the material. There are potentially large differences in temperatures at different circumferential locations on the tube. Because of this, the effects of temperature dependent material properties on the stresses and deformations may be important. The study is composed of three parts: experiments to determine the functional form of the circumferential gradient and to measure tube deflections; an elasticity solution to compute the stresses and deformations; and an approximate approach to determine the effects of temperature dependent material properties.

Cooper, D. E.↗
NASA NTRS1984

Residual stresses in cross-ply composite tubes

The residual thermal stresses in 4-layer cross-ply tubes are studied. The tubes considered has a small radius to wall-thickness ratios and so elasticity solutions were used. The residual thermal stress problem was considered to be axisymmetric and three elasticity solutions were derived and the results compared with the results using classical lamination theory. The comparison illustrates the limitations of classical lamination theory. The three elasticity solutions derived were: plane stress, plane strain, and generalized plane strain, the latter being the most realistic. Residual stresses in both the hoop and axial direction is significant. Stacking arrangement effects the residual stress to some extent, as do the material properties of the individual lamina. The benefits of hybrid construction are briefly discussed.

Cohen, D.↗
NASA NTRS1984

The effects of thermal cycling on matrix cracking and stiffness changes in composite tubes

The study investigated the accumulation of transverse matrix cracks and the resultant loss of torsional, extensional, and bending stiffnesses in 8 layer 0.5 in. diameter crossply tubes subjected to thermal cycling. The tubes were graphite-epoxy and the temperature range during cycling was -250 to 200 F. The effect of fiber and matrix properties was investigated through the use of T300 and P75S fibers and 934 and CE339 resins. The study considered 0, 10, 50, 100, 300, and 500 thermal cycles. Photomicrographs, X-rays, and edge replication were used to evaluate cracking. Special loading fixtures were used to measure stiffness changes. An important finding was that for the tubes studied, even with extensive cracking, the bending and extensional stiffnesses were not affected. The torsional stiffness, however, was strongly affected.

Cohen, D.↗
NASA NTRS1984

Residual thermal stresses in cross-ply graphite-epoxy tubes

Elasticity solutions for the residual stress state in cross-ply graphite-epoxy tubes subjected to a spatially uniform temperature below the cure temperature are derived. The solutions are valid away from the ends of the tube. Numerical results are presented for three tubes. It is seen that stacking arrangement can affect the residual stresses and that the radial stresses are smaller than the other stress components. The results show that classical lamination theory is in considerable error when the tube radius to wall thickness ratio is less than 20.

Hyer, M. W.↗
NASA NTRS1979

VLSI system for synthetic aperture radar /SAR/ processing

The paper discusses an SAR problem based on actual requirements set forth by NASA for a spaceborne application. The requirements for high resolution and high quality necessitate a data sampling rate of 7.5 MHz. For each data value 1,025 4-bit complex multiply + add operations are needed, which is equivalent to 7.7 GHz complex multiply + add operation rate. Since this rate is much too high for general purpose systems, a special-purpose device was sought. This paper discusses two architectures based on parallel operation of 1,025 identical cells, each of which is capable of performing arithmetic, storage, and several control operations. The operation rate in each device is only 7.5 MHz, which is quite manageable, especially with the help of a substantial degree of pipelining. A computational-mathematical analysis is used as a primary tool for evaluating the design and some of its tradeoffs. Two different approaches are discussed and compared; both are based on having 1,025 identical cells working in parallel, but differ in their dual approaches to the flow of data.

Cohen, D.↗
NASA NTRS1976

An analysis of the stability of an airplane with free controls

The conditions essential to the stability of an airplane with free control surfaces are studied. Calculations are based on typical airplane characteristics with certain factors varied to cover a range of current designs. The effects of reducing the chord and of eliminating the floating tendency of the surface, of changing the wing loading and of decreasing the radius of gyration of the airplane are indicated. An investigation has also been made of the nature of the motion of the airplane with controls free and of the modes of instability that may occur. Stability with the controls free generally depends more critically on the design of the control system than on the stability characteristics of the airplane.

Jones, R. T.↗
NASA NTRS1976

A graphical method of determining pressure distribution in two-dimensional flow

By a generalization of the Joukowski method, a procedure is developed for effecting localized modifications of airfoil shapes and for determining graphically the resultant changes in the pressure distribution. The application of the procedure to the determination of the pressure distribution over airfoils of original design is demonstrated. Formulas for the lift, the moment, and the aerodynamic center are also given.

Jones, R. T.↗
NASA NTRS1976

Determination of optimum planforms for control surfaces

A theoretical analysis is made to determine the optimum chord distribution, location, and extent of control surfaces, with the ratio of hinge moment to effectiveness as the criterion. Expressions for the effectiveness - for ailerons, the rolling moment, and for tail surfaces, the change of lift on the tail due to deflection of the surface-were derived from lifting line theory. Solutions found for a range of airfoil planforms indicate that, regardless of the characteristics of the tail surface, the chord of the rudder or the elevator should be very nearly constant over its span. The optimum ailerons are also of a characteristics shape, varying little with the planform of the wing.

Jones, R. T.↗
NASA NTRS1974

A miniature high voltage plasma interaction flight experiment - Project MINX

A miniature high-voltage array was fabricated, incorporating the multi-junction edge illuminated (MJC) cell technique. The array consists of 32 2x2.2 cm MJCs, series connected, capable of 1600 V open circuit at 1 AMO and 1.2 mA short circuit. A solid state, high-voltage relay is connected across each 4-cell subgroup of the array. It was built to test plasma current drain on space systems using high voltage as might occur when a high-voltage solar array is operated from low to synchronous orbit.

Riley, T. J.↗
NASA NTRS1969

Fluid sample collection and storage device

Fluid sampling device collects a sample from a low-pressure fluid system and stores it for an indefinite period, with little risk of contamination of either the sample or the surrounding environment. The collector /a plastic bladder/ is separated from the sampler after a sample is collected.

Cohen, D.↗
NASA NTRS1969

Study of actinide chemistry in saturated potassium fluoride solution

Study concerning the chemistry of actinides in saturated KF solution included work with neptunium, uranium, and americium. Solubilities, absorption spectra, oxidation-reduction reactions, and solid compounds which can be produced in KF solution were examined. The information is used for preparation of various materials from salts of the actinides.

Cohen, D.↗