Search NASA⌕ Search

Engineering topics

Colandrea, C.

Publications and source records attributed to Colandrea, C..

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

An upper pressure limit for low- Z benign termination of runaway electron beams in TCV

Abstract We present a model for the particle balance in the post-disruption runaway electron plateau phase of a tokamak discharge. The model is constructed with the help of, and applied to, experimental data from TCV discharges investigating the so-called ‘low- Z benign termination’ runaway electron mitigation scheme. In the benign termination scheme, the free electron density is first reduced in order for a subsequently induced MHD instability to grow rapidly and spread the runaway electrons widely across the wall. We show that the observed non-monotonic dependence of the free electron density with the measured neutral pressure is due to plasma re-ionization induced by runaway electron impact ionization. At higher neutral pressures, more target particles are present in the plasma for runaway electrons to collide with and ionize. Parameter scans are conducted to clarify the role of the runaway electron density and energy on the free electron density, and it is found that only the runaway electron density has a noticeable impact. While the free electron density is shown to be related to the spread of heat fluxes at termination, the exact cause for the upper neutral pressure limit remains undetermined and an object for further study.

Hoppe, M. (ORCID:0000000339948977)↗
DOE OSTI2024

Comparison of detachment in Ohmic plasmas with positive and negative triangularity

Abstract In recent years, negative triangularity (NT) has emerged as a potential high-confinement L-mode reactor solution. In this work, detachment is investigated using core density ramps in lower single null Ohmic L-mode plasmas across a wide range of upper, lower, and average triangularity (the mean of upper and lower triangularity: δ ) in the TCV tokamak. It is universally found that detachment is more difficult to access for NT shaping. The outer divertor leg of discharges with δ ≈ − 0.3 could not be cooled to below 5 eV through core density ramps alone. The behavior of the upstream plasma and geometrical divertor effects (e.g. a reduced connection length with negative lower triangularity) do not fully explain the challenges in detaching NT plasmas. Langmuir probe measurements of the target heat flux widths ( λ q ) were constant to within 30% across an upper triangularity scan, while the spreading factor S was lower by up to 50% for NT, indicating a generally lower integral scrape-off layer width, λ int . The line-averaged core density was typically higher for NT discharges for a given fuelling rate, possibly linked to higher particle confinement in NT. Conversely, the divertor neutral pressure and integrated particle fluxes to the targets were typically lower for the same line-averaged density, indicating that NT configurations may be closer to the sheath-limited regime than their PT counterparts, which may explain why NT is more challenging to detach.

Physics↗
DOE OSTI2024

Benign termination of runaway electron beams on ASDEX Upgrade and TCV

Abstract This paper discusses the development of a benign termination scenario for runaway electron (RE) beams on ASDEX Upgrade and TCV. A systematic study revealed that a low electron density (n e ) companion plasma was required to achieve a large MHD instability, which expelled the confined REs over a large wetted area and allowed for the conversion of magnetic energy to radiation. Control of the companion plasma n e was achieved via neutral pressure regulation and was agnostic to material injection method. The neutral pressure required for recombination was found to be dependent on impurity species, quantity and RE current. On TCV,n e increased at neutral pressures above 1 Pa, indicating that higher collisionality between the REs and neutrals may lead to an upper pressure limit. The conversion of magnetic energy to radiated energy was measured on both machines and a decrease in efficiency was observed at high neutral pressure on TCV. The benign termination technique was able to prevent any significant increase in maximum heat flux on AUG from 200 to 600 kA of RE current, highlighting the ability of this approach to handle fully formed RE beams.

Physics↗
DOE OSTI2024

The effect of plasma shaping on high density H-mode SOL profiles and fluctuations in TCV

Abstract The impact of plasma shaping on the properties of high density H-mode scrape-off layer (SOL) profiles and transport at the outer midplane has been investigated on Tokamakà configuration variable. The experimental dataset has been acquired by evolving the upper triangularity while keeping the other parameters constant. The scan comprises δ u p values between 0.0 and 0.6, excluding negative triangularity scenarios. Within this study, a transition from type-I edge localised modes to the quasi-continuous exhaust regime takes place from low to high δ u p . The modification of the upstream SOL profiles has been assessed, in terms of separatrix quantities, within the α t turbulence control parameter theoretical framework (Eich et al 2020 Nucl. Fusion 60 056016). The target parallel heat load and the upstream near-SOL density profiles have been shown to broaden significantly for increasing α t . Correspondingly, in the far SOL a density shoulder formation is observed when moving from low to high δ u p . These behaviours have been correlated with an enhancement of the SOL fluctuation level, as registered by wall-mounted Langmuir probes as well as the thermal helium beam diagnostic. Specifically, both the background and the filamentary-induced fluctuating parts of the first wall ion saturation current signal are larger at higher δ u p , with filaments being ejected more frequently into the SOL. Comparison of two pulses at the extremes of the δ u p scan range, but with otherwise same input parameters, shows that the midplane neutral pressure does not change much during the H-mode phase of the discharge. This indicates that indirect effects of the change in geometry, linked to first wall recycling sources, should not play a significant role. The total core radiation increases at high δ u p , on account of a stronger plasma–wall interaction and resulting larger carbon impurity intake from the first wall. This is likely associated to the enhanced first wall fluctuations, as well as a smaller outer gap and the close-to-double-null magnetic topology at high shaping.

Stagni, A. (ORCID:0000000180841544)↗
DOE OSTI2023

Estimating cross-field particle transport at the outer midplane of TCV by tracking filaments with machine learning

Abstract Cross-field transport of particles in the boundary region of magnetically confined fusion plasmas is dominated by turbulence. Blobs, intermittent turbulent structures with large amplitude and a filamentary shape appearing in the scrape-off layer (SOL), are known from theoretical and experimental studies to be the main contributor to the cross-field particle transport. The dynamics of blobs differs depending on various plasma conditions, including triangularity ( δ ). In this work, we analyze triangularity dependence of the cross-field particle transport at the outer midplane of plasmas with δ = + 0.38 , +0.15, −0.14, and −0.26 on the Tokamak à Configuration Variable, using our novel machine learning (ML) blob-tracking approach applied to gas puff imaging data. The cross-field particle flux determined in this way is of the same order as the overall transport inferred from KN1D, GBS, and SOLPS-ITER simulations, suggesting that the blobs identified by the ML blob-tracking account for most of the cross-field particle transport in the SOL. Also, the ML blob-tracking and KN1D show a decrease in the cross-field particle transport as δ becomes more negative. The blob-by-blob analysis of the result from the tracking reveals that the decrease of cross-field particle transport with decreasing δ is accompanied by a decrease in the number of blobs in a fixed time, which tend to have larger area and lower radial speed. Also, the blobs in these plasmas are in the connected sheath regime, and show a velocity scaling consistent with the two-region model.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Validation of 2D Te and ne measurements made with Helium imaging spectroscopy in the volume of the TCV divertor

Abstract Multi-spectral imaging of helium atomic emission (HeMSI) has been used to create 2D poloidal maps of T e and n e in TCV’s divertor. To achieve these measurements, TCV’s MANTIS multispectral cameras (Perek et al 2019 Rev. Sci. Instrum. 90 123514) simultaneously imaged four He I lines (two singlet and two triplet) and a He II line (468 nm) from passively present He and He + . The images, which were absolutely calibrated and covered the whole divertor region, were inverted through the assumption of toroidal symmetry to create emissivity profiles and, consequently, line-ratio profiles. A collisional-radiative model (CRM) was applied to the line-ratio profiles to produce 2D poloidal maps of T e and n e . The collisional-radiative modeling was accomplished with the Goto helium CRM code (Zholobenko et al 2018 Nucl. Fusion 58 126006, Zholobenko et al 2018 Technical Report , Goto 2003 J. Quant. Spectrosc. Radiat. Transfer 76 331–44) which accounts for electron-impact excitation (EIE) and deexcitation, and electron–ion recombination (EIR) with He + . The HeMSI T e and n e measurements were compared with co-local Thomson scattering measurements. The two sets of measurements exhibited good agreement for ionizing plasmas: ( 5 eV ⩽ T e ⩽ 60 eV , and 2 × 10 18 m − 3 ⩽ n e ⩽ 3 × 10 19 m − 3 ) in the case of majority helium plasmas, and ( 10 eV ⩽ T e ⩽ 40 eV , 2 × 10 18 m − 3 ⩽ n e ⩽ 3 × 10 19 m − 3 ) in the case of majority deuterium plasmas. However, there were instances where HeMSI measurements diverged from Thomson scattering. When T e ⩽ 10 eV in majority deuterium plasmas, HeMSI deduced inaccurately high values of T e . This disagreement cannot be rectified within the CRM’s EIE and EIR framework. Second, on sporadic occasions within the private flux region, HeMSI produced erroneously high measurements of n e . Multi-spectral imaging of Helium emission has been demonstrated to produce accurate 2D poloidal maps of T e and n e within the divertor of a tokamak for plasma conditions relevant to contemporary divertor studies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Dependence of scrape-off layer profiles and turbulence on gas fuelling in high density H-mode regimes in TCV

A set of high density, highly shaped H-mode discharges has been performed in the TCV tokamak with the aim of assessing the effects of increasing divertor neutral recycling on the properties of upstream inter-ELM scrape-off layer (SOL) profiles and transport. An increase of divertor neutral pressure has been correlated with the evolution of separatrix properties and turbulence level. The latter has been quantified by means of the α t parameter introduced in (Eich 2020 Nucl. Fusion 60 056016), describing the contribution of resistive-interchange turbulence in the SOL relative to drift wave transport. The analysis reveals a general broadening of the upstream SOL profiles as α t increases, with the SOL power width measured by the vertical IR thermography system increasing significantly. In a similar way, the upstream density profile widens in the near SOL, whereas in the far SOL a density shoulder is observed to progressively form and increase in amplitude. This behaviour is associated with an enhancement of far SOL turbulent transport in the form of blob-filaments travelling radially faster across the far SOL and becoming bigger at higher α t . Finally, the detected filaments, evaluated from the fast reciprocating probe at the outer midplane, are determined to mostly belong to the resistive ballooning and resistive X-point regimes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Validation of edge turbulence codes against the TCV-X21 diverted L-mode reference case

Self-consistent full-size turbulent-transport simulations of the divertor and scrape-off-layer (SOL) of existing tokamaks have recently become feasible. This enables the direct comparison of turbulence simulations against experimental measurements. In this work, we perform a series of diverted ohmic L-mode discharges on the tokamak à configuration variable (TCV) tokamak, building a first-of-a-kind dataset for the validation of edge turbulence models. This dataset, referred to as TCV-X21, contains measurements from five diagnostic systems from the outboard midplane (OMP) to the divertor targets—giving a total of 45 one- and two-dimensional comparison observables in two toroidal magnetic field directions. The experimental dataset is used to validate three flux-driven 3D fluid-turbulence models—GBS, GRILLIX and TOKAM3X. With each model, we perform simulations of the TCV-X21 scenario, individually tuning the particle and power source rates to achieve a reasonable match of the upstream separatrix value of density and electron temperature. We find that the simulations match the experimental profiles for most observables at the OMP—both in terms of profile shape and absolute magnitude—while a comparatively poorer agreement is found towards the divertor targets. The match between simulation and experiment is seen to be sensitive to the value of the resistivity, the heat conductivities, the power injection rate and the choice of sheath boundary conditions. Additionally, despite targeting a sheath-limited regime, the discrepancy between simulations and experiment also suggests that the neutral dynamics should be included. The results of this validation show that turbulence models are able to perform simulations of existing devices and achieve reasonable agreement with experimental measurements. Where disagreement is found, the validation helps to identify how the models can be improved. By publicly releasing the experimental dataset and validation analysis, this work should help to guide and accelerate the development of predictive turbulence simulations of the edge and SOL.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Relevance of E × B drifts for particle and heat transport in divertors

Radial electric fields up to ~4 kV m –1 are observed in the boundary between the private flux region (PFR) and the scrape-off layer (SOL) driving E × B drifts between the inner and outer targets at speeds up to 2.8 km s –1 in the Tokamak à configuration variable divertor. The resulting E × B fluxes, located in a narrow region ($\Delta {\rho _\Psi } < 0.012$ in normalized radius or $\Delta $ R – R sep <4 mm mapped to the outer midplane) are equivalent to around 20% of the total heat and particle flux to the divertor targets (inner + outer). At the peak E r , the E × B poloidal transport is equivalent to parallel flows with M ∥ ~ 3. In the snowflake divertor with a second X-point in the outer SOL, the drifts in the PFR-SOL boundary were equivalent to around 30% of the total heat and particle flux to the divertor targets and cover a region ~50% wider than in the single null ($\Delta {\rho _\Psi }$ ~ 0.018, $\Delta $R – R sep ~ 6 mm). Furthermore, the location of the PFR-SOL boundary drift shifts radially in the E ∥ × B direction when reversing the toroidal field direction. Peaks in density and electron pressure have been identified near the primary X-point along with large gradients in density, temperature, and potential, the latter resulting in a local electric field ~2.7 kV m –1 which drives a drift (1.9 km s –1 ) upwards towards the closed flux surfaces. Floating potential (V f ) magnitudes up to 75 V (~2 kT e ) were measured, indicating that V f and parallel currents should not be neglected when estimating plasma potential.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

SOLPS-ITER validation with TCV L-mode discharges

This work presents a quantitative test of SOLPS-ITER simulations against tokamak a configuration variable (TCV) L-mode experiments. These simulations account for drifts, currents, kinetic neutrals, and carbon impurities providing the most complete edge transport simulations for TCV to date. The comparison is performed on nominally identical discharges carried out to assess the effectiveness of TCV’s divertor baffles in the framework of the European Plasma Exhaust program and employs numerous edge diagnostics providing a detailed code-experiment benchmark for TCV. The simulations show a qualitative consistency, but the quantitative differences remain, which are assessed herein. It is found that, for a given separatrix density, the simulations most notably yield a colder, and denser, divertor state with a higher divertor neutral pressure than measured.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Initial TCV operation with a baffled divertor

The Tokamak à Configuration Variable (TCV) tokamak is in the midst of an upgrade to further its capability to investigate conventional and alternative divertor configurations. To that end, modular and removable gas baffles have been installed to decrease the coupling between the divertor and the plasma core. The baffles primarily seek to suppress the transit of recycling neutrals to closed flux surfaces. A first experimental campaign with the gas baffles has shown that the baffled divertor remains compatible with a wide range of configurations including snowflake and super-X divertors. Plasma density ramp experiments reveal an increase of the neutral pressure in the divertor by up to a factor ×5 compared to the unbaffled divertor and thereby qualitatively confirm simulations with the SOLPS-ITER code that were used to guide the baffle design. Finally, together with a range of new and upgraded divertor diagnostics, the baffled TCV divertor is now used to validate divertor models for ITER and next step devices with particular emphasis on geometric variations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗