Search NASA⌕ Search

Engineering topics

Cole, J. E., III

Publications and source records attributed to Cole, J. E., III.

Structureborne noise measurements on a small twin-engine aircraft

Structureborne noise measurements performed on a twin-engine aircraft (Beechcraft Baron) are reported. There are two overall objectives of the test program. The first is to obtain data to support the development of analytical models of the wing and fuselage, while the second is to evaluate effects of structural parameters on cabin noise. Measurements performed include structural and acoustic responses to impact excitation, structural and acoustic loss factors, and modal parameters of the wing. Path alterations include added mass to simulate fuel, variations in torque of bolts joining wing and fuselage, and increased acoustic absorption. Conclusions drawn regarding these measurements are presented.

Cole, J. E., III↗

Analytical modeling of the structureborne noise path on a small twin-engine aircraft

The structureborne noise path of a six passenger twin-engine aircraft is analyzed. Models of the wing and fuselage structures as well as the interior acoustic space of the cabin are developed and used to evaluate sensitivity to structural and acoustic parameters. Different modeling approaches are used to examine aspects of the structureborne path. These approaches are guided by a number of considerations including the geometry of the structures, the frequency range of interest, and the tractability of the computations. Results of these approaches are compared with experimental data.

Cole, J. E., III↗

All-theoretical prediction of cabin noise due to impingement of propeller vortices on a wing structure

Reported calculations of structure-borne cabin noise for a small twin engine aircraft powered by tractor propellers rely on the following three-stage methodological breakup of the problem: (1) the unsteady-aerodynamic prediction of wing lift harmonics caused by the whipping action of the vortex system trailed from each propeller; (2) the associated wing/fuselage structural response; (3) the cabin noise field for the computed wall vibration. The first part--the estimate of airloads--skirts a full-fledged aeroelastic situation by assuming the wing to be fixed in space while cancelling the downwash field of the cutting vortices. The model is based on an approximate high-frequency lifting-surface theory justified by the blade rate and flight Mach number of application. Its results drive a finite-element representation of the wing accounting for upper and lower skin surfaces, spars, ribs, and the presence of fuel. The fuselage, modeled as a frame-stiffened cylindrical shell, is bolted to the wing.

Martinez, R.↗

Structureborne noise investigations of a twin engine aircraft

The interior noise of aircraft powered by advanced turbo-prop concepts is likely to have nonnegligible contributions from structureborne paths, these paths being those involving propeller loads transmitted to the structures of the lifting surfaces. As a means of examining these paths, structural measurements have been performed on a small twin-engine aircraft, and in addition analytical models of the structure have been developed. In this paper results from both portions of this study are presented.

Garrelick, J. M.↗

Analytical model of the structureborne interior noise induced by a propeller wake

The structure-borne contribution to the interior noise that is induced by the propeller wake acting on the wing was studied. Analytical models were developed to describe each aspect of this path including the excitation loads, the wing and fuselage structures, and the interior acoustic space. The emphasis is on examining a variety of parameters, and as a result different models were developed to examine specific parameters. The excitation loading on the wing by the propeller wake is modeled by a distribution of rotating potential vortices whose strength is related to the thrust per blade. The response of the wing to this loading is examined using beam models. A model of a beam structurally connected to a cylindrical shell with an internal acoustic fluid was developed to examine the coupling of energy from the wing to the interior space. The model of the acoustic space allows for arbitrary end conditions (e.g., rigid or vibrating end caps). Calculations are presented using these models to compare with a laboratory test configuration as well as for parameters of a prop-fan aircraft.

Junger, M. C.↗

Investigation of the effects of a moving acoustic medium on jet noise measurements

Noise from an unheated sonic jet in the presence of an external flow is measured in a free-jet wind tunnel using microphones located both inside and outside the flow. Comparison of the data is made with results of similar studies. The results are also compared with theoretical predictions of the source strength for jet noise in the presence of flow and of the effects of sound propagation through a shear layer.

Cole, J. E., III↗

Acoustic pulse propagation in a duct with flow

The effect of a mean flow on acoustic pulse propagation in a wind tunnel of rectangular cross-section is considered both experimentally and theoretically. Pulse shapes in the wind tunnel are recorded by microphones located upstream and downstream of a source. A theoretical model of pulse propagation from a point source located in an infinitely-long rectangular duct carrying a uniform flow is considered. The convective wave equation with boundary conditions appropriate to hard walls is solved by using the Laplace transform. For the input pulse shape used in the experiments, the solution is obtained by numerically evaluating the inverse Laplace transform. The results of experiment and theory are seen to be in good agreement.

Cole, J. E., III↗

Acoustic power of a moving point source in a moving medium

The acoustic power output of a moving point-mass source in an acoustic medium which is in uniform motion and infinite in extent is examined. The acoustic medium is considered to be a homogeneous fluid having both zero viscosity and zero thermal conductivity. Two expressions for the acoustic power output are obtained based on a different definition cited in the literature for the average energy-flux vector in an acoustic medium in uniform motion. The acoustic power output of the source is found by integrating the component of acoustic intensity vector in the radial direction over the surface of an infinitely long cylinder which is within the medium and encloses the line of motion of the source. One of the power expressions is found to give unreasonable results even though the flow is uniform.

Cole, J. E., III↗

Sound propagation from a simple source in a wind tunnel

The nature of the acoustic field of a simple source in a wind tunnel under flow conditions was examined theoretically and experimentally. The motivation of the study was to establish aspects of the theoretical framework for interpreting acoustic data taken (in wind) tunnels using in wind microphones. Three distinct investigations were performed and are described in detail.

Cole, J. E., III↗

The influence of a crossflow on jet noise

The acoustic field generated by a circular jet in the presence of a low speed crossflow is calculated. The solution is obtained for a quadrupole source located in a uniformly moving acoustic medium. Ribner's work on straight jets is used to model the flow in the turbulent crossflow jet. The movement of the acoustic medium results in the acoustic intensity being greater upstream of the jet flow than at an equal distance downstream. A summary is also presented of the analysis for the acoustic intensity of a crossflow jet which is in motion through a stationary acoustic medium. The analysis is applicable to the noise generated by the lift jet of a V/STOL aircraft under take-off or landing conditions. The results of these two configurations provide a comparision of the directional distribution of acoustic intensity measured in a wind tunnel test of a crossflow jet and in a corresponding flight test.

Cole, J. E., III↗